Merge libata branch 'chs-support' to latest upstream kernel.

10 files changed, 491 insertions, 87 deletions

diff --git a/include/linux/8250_pci.h b/include/linux/8250_pci.h
index 5f3ab21b339b..3209dd46ea7d 100644
--- a/include/linux/8250_pci.h
+++ b/include/linux/8250_pci.h
@@ -1,2 +1,37 @@
-int pci_siig10x_fn(struct pci_dev *dev, int enable);
-int pci_siig20x_fn(struct pci_dev *dev, int enable);
+/*
+ * Definitions for PCI support.
+ */
+#define FL_BASE_MASK		0x0007
+#define FL_BASE0		0x0000
+#define FL_BASE1		0x0001
+#define FL_BASE2		0x0002
+#define FL_BASE3		0x0003
+#define FL_BASE4		0x0004
+#define FL_GET_BASE(x)		(x & FL_BASE_MASK)
+
+/* Use successive BARs (PCI base address registers),
+   else use offset into some specified BAR */
+#define FL_BASE_BARS		0x0008
+
+/* do not assign an irq */
+#define FL_NOIRQ		0x0080
+
+/* Use the Base address register size to cap number of ports */
+#define FL_REGION_SZ_CAP	0x0100
+
+struct pciserial_board {
+	unsigned int flags;
+	unsigned int num_ports;
+	unsigned int base_baud;
+	unsigned int uart_offset;
+	unsigned int reg_shift;
+	unsigned int first_offset;
+};
+
+struct serial_private;
+
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
+void pciserial_remove_ports(struct serial_private *priv);
+void pciserial_suspend_ports(struct serial_private *priv);
+void pciserial_resume_ports(struct serial_private *priv);
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 6962e26fc6df..85169ea9eb01 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -1,24 +1,29 @@
 
 /*
-   Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
-   Copyright 2003-2004 Jeff Garzik
-
-   The contents of this file are subject to the Open
-   Software License version 1.1 that can be found at
-   http://www.opensource.org/licenses/osl-1.1.txt and is included herein
-   by reference.
-
-   Alternatively, the contents of this file may be used under the terms
-   of the GNU General Public License version 2 (the "GPL") as distributed
-   in the kernel source COPYING file, in which case the provisions of
-   the GPL are applicable instead of the above.  If you wish to allow
-   the use of your version of this file only under the terms of the
-   GPL and not to allow others to use your version of this file under
-   the OSL, indicate your decision by deleting the provisions above and
-   replace them with the notice and other provisions required by the GPL.
-   If you do not delete the provisions above, a recipient may use your
-   version of this file under either the OSL or the GPL.
-
+ *  Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
+ *  Copyright 2003-2004 Jeff Garzik
+ *
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ *  libata documentation is available via 'make {ps|pdf}docs',
+ *  as Documentation/DocBook/libata.*
+ *
+ *  Hardware documentation available from http://www.t13.org/
+ *
  */
 
 #ifndef __LINUX_ATA_H__
@@ -108,6 +113,8 @@ enum {
 
 	/* ATA device commands */
 	ATA_CMD_CHK_POWER	= 0xE5, /* check power mode */
+	ATA_CMD_STANDBY		= 0xE2, /* place in standby power mode */
+	ATA_CMD_IDLE		= 0xE3, /* place in idle power mode */
 	ATA_CMD_EDD		= 0x90,	/* execute device diagnostic */
 	ATA_CMD_FLUSH		= 0xE7,
 	ATA_CMD_FLUSH_EXT	= 0xEA,
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index a0ab26aab450..d7021c391b2b 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -408,6 +408,8 @@ struct ethtool_ops {
 #define SUPPORTED_FIBRE			(1 << 10)
 #define SUPPORTED_BNC			(1 << 11)
 #define SUPPORTED_10000baseT_Full	(1 << 12)
+#define SUPPORTED_Pause			(1 << 13)
+#define SUPPORTED_Asym_Pause		(1 << 14)
 
 /* Indicates what features are advertised by the interface. */
 #define ADVERTISED_10baseT_Half		(1 << 0)
@@ -423,6 +425,8 @@ struct ethtool_ops {
 #define ADVERTISED_FIBRE		(1 << 10)
 #define ADVERTISED_BNC			(1 << 11)
 #define ADVERTISED_10000baseT_Full	(1 << 12)
+#define ADVERTISED_Pause		(1 << 13)
+#define ADVERTISED_Asym_Pause		(1 << 14)
 
 /* The following are all involved in forcing a particular link
  * mode for the device for setting things.  When getting the
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 973090be7fc4..7b2116ddd26a 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1,23 +1,26 @@
 /*
-   Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
-   Copyright 2003-2004 Jeff Garzik
-
-   The contents of this file are subject to the Open
-   Software License version 1.1 that can be found at
-   http://www.opensource.org/licenses/osl-1.1.txt and is included herein
-   by reference.
-
-   Alternatively, the contents of this file may be used under the terms
-   of the GNU General Public License version 2 (the "GPL") as distributed
-   in the kernel source COPYING file, in which case the provisions of
-   the GPL are applicable instead of the above.  If you wish to allow
-   the use of your version of this file only under the terms of the
-   GPL and not to allow others to use your version of this file under
-   the OSL, indicate your decision by deleting the provisions above and
-   replace them with the notice and other provisions required by the GPL.
-   If you do not delete the provisions above, a recipient may use your
-   version of this file under either the OSL or the GPL.
-
+ *  Copyright 2003-2005 Red Hat, Inc.  All rights reserved.
+ *  Copyright 2003-2005 Jeff Garzik
+ *
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2, or (at your option)
+ *  any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; see the file COPYING.  If not, write to
+ *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ *  libata documentation is available via 'make {ps|pdf}docs',
+ *  as Documentation/DocBook/libata.*
+ *
  */
 
 #ifndef __LINUX_LIBATA_H__
@@ -114,6 +117,8 @@ enum {
 	ATA_FLAG_MMIO		= (1 << 6), /* use MMIO, not PIO */
 	ATA_FLAG_SATA_RESET	= (1 << 7), /* use COMRESET */
 	ATA_FLAG_PIO_DMA	= (1 << 8), /* PIO cmds via DMA */
+	ATA_FLAG_NOINTR		= (1 << 9), /* FIXME: Remove this once
+					     * proper HSM is in place. */
 
 	ATA_QCFLAG_ACTIVE	= (1 << 1), /* cmd not yet ack'd to scsi lyer */
 	ATA_QCFLAG_SG		= (1 << 3), /* have s/g table? */
@@ -369,7 +374,7 @@ struct ata_port_operations {
 
 	void (*host_stop) (struct ata_host_set *host_set);
 
-	void (*bmdma_stop) (struct ata_port *ap);
+	void (*bmdma_stop) (struct ata_queued_cmd *qc);
 	u8   (*bmdma_status) (struct ata_port *ap);
 };
 
@@ -430,7 +435,7 @@ extern void ata_dev_id_string(u16 *id, unsigned char *s,
 extern void ata_dev_config(struct ata_port *ap, unsigned int i);
 extern void ata_bmdma_setup (struct ata_queued_cmd *qc);
 extern void ata_bmdma_start (struct ata_queued_cmd *qc);
-extern void ata_bmdma_stop(struct ata_port *ap);
+extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
 extern u8   ata_bmdma_status(struct ata_port *ap);
 extern void ata_bmdma_irq_clear(struct ata_port *ap);
 extern void ata_qc_complete(struct ata_queued_cmd *qc, u8 drv_stat);
@@ -650,7 +655,7 @@ static inline void scr_write(struct ata_port *ap, unsigned int reg, u32 val)
 	ap->ops->scr_write(ap, reg, val);
 }
 
-static inline void scr_write_flush(struct ata_port *ap, unsigned int reg, 
+static inline void scr_write_flush(struct ata_port *ap, unsigned int reg,
 				   u32 val)
 {
 	ap->ops->scr_write(ap, reg, val);
diff --git a/include/linux/mii.h b/include/linux/mii.h
index 374b615ea9ea..9b8d0476988a 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -22,6 +22,7 @@
 #define MII_EXPANSION       0x06        /* Expansion register          */
 #define MII_CTRL1000        0x09        /* 1000BASE-T control          */
 #define MII_STAT1000        0x0a        /* 1000BASE-T status           */
+#define MII_ESTATUS	    0x0f	/* Extended Status */
 #define MII_DCOUNTER        0x12        /* Disconnect counter          */
 #define MII_FCSCOUNTER      0x13        /* False carrier counter       */
 #define MII_NWAYTEST        0x14        /* N-way auto-neg test reg     */
@@ -54,7 +55,10 @@
 #define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
 #define BMSR_RFAULT             0x0010  /* Remote fault detected       */
 #define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
-#define BMSR_RESV               0x07c0  /* Unused...                   */
+#define BMSR_RESV               0x00c0  /* Unused...                   */
+#define BMSR_ESTATEN		0x0100	/* Extended Status in R15 */
+#define BMSR_100FULL2		0x0200	/* Can do 100BASE-T2 HDX */
+#define BMSR_100HALF2		0x0400	/* Can do 100BASE-T2 FDX */
 #define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
 #define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
 #define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
@@ -114,6 +118,9 @@
 #define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
 #define EXPANSION_RESV          0xffe0  /* Unused...                   */
 
+#define ESTATUS_1000_TFULL	0x2000	/* Can do 1000BT Full */
+#define ESTATUS_1000_THALF	0x1000	/* Can do 1000BT Half */
+
 /* N-way test register. */
 #define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
 #define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index f90f674eb3b0..9a0893f3249e 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -63,11 +63,12 @@ struct device;
 
 struct mmc_host {
 	struct device		*dev;
+	struct class_device	class_dev;
+	int			index;
 	struct mmc_host_ops	*ops;
 	unsigned int		f_min;
 	unsigned int		f_max;
 	u32			ocr_avail;
-	char			host_name[8];
 
 	/* host specific block data */
 	unsigned int		max_seg_size;	/* see blk_queue_max_segment_size */
@@ -97,6 +98,7 @@ extern void mmc_free_host(struct mmc_host *);
 
 #define mmc_priv(x)	((void *)((x) + 1))
 #define mmc_dev(x)	((x)->dev)
+#define mmc_hostname(x)	((x)->class_dev.class_id)
 
 extern int mmc_suspend_host(struct mmc_host *, pm_message_t);
 extern int mmc_resume_host(struct mmc_host *);
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index dce53ac1625d..97bbccdbcca3 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -33,7 +33,8 @@ struct ieee1394_device_id {
 	__u32 model_id;
 	__u32 specifier_id;
 	__u32 version;
-	kernel_ulong_t driver_data;
+	kernel_ulong_t driver_data
+		__attribute__((aligned(sizeof(kernel_ulong_t))));
 };
 
 
@@ -182,7 +183,11 @@ struct of_device_id
 	char	name[32];
 	char	type[32];
 	char	compatible[128];
+#if __KERNEL__
 	void	*data;
+#else
+	kernel_ulong_t data;
+#endif
 };
 
 
@@ -208,7 +213,8 @@ struct pcmcia_device_id {
 #ifdef __KERNEL__
 	const char *	prod_id[4];
 #else
-	kernel_ulong_t	prod_id[4];
+	kernel_ulong_t	prod_id[4]
+		__attribute__((aligned(sizeof(kernel_ulong_t))));
 #endif
 
 	/* not matched against */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 927ed487630d..499a5325f67f 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1249,6 +1249,7 @@
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA	0x0266
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2	0x0267
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE	0x036E
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA	0x036F
 #define PCI_DEVICE_ID_NVIDIA_NVENET_12		0x0268
 #define PCI_DEVICE_ID_NVIDIA_NVENET_13		0x0269
 #define PCI_DEVICE_ID_NVIDIA_MCP51_AUDIO	0x026B
diff --git a/include/linux/phy.h b/include/linux/phy.h
new file mode 100644
index 000000000000..72cb67b66e0c
--- /dev/null
+++ b/include/linux/phy.h
@@ -0,0 +1,377 @@
+/*
+ * include/linux/phy.h
+ *
+ * Framework and drivers for configuring and reading different PHYs
+ * Based on code in sungem_phy.c and gianfar_phy.c
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __PHY_H
+#define __PHY_H
+
+#include <linux/spinlock.h>
+#include <linux/device.h>
+
+#define PHY_BASIC_FEATURES	(SUPPORTED_10baseT_Half | \
+				 SUPPORTED_10baseT_Full | \
+				 SUPPORTED_100baseT_Half | \
+				 SUPPORTED_100baseT_Full | \
+				 SUPPORTED_Autoneg | \
+				 SUPPORTED_TP | \
+				 SUPPORTED_MII)
+
+#define PHY_GBIT_FEATURES	(PHY_BASIC_FEATURES | \
+				 SUPPORTED_1000baseT_Half | \
+				 SUPPORTED_1000baseT_Full)
+
+/* Set phydev->irq to PHY_POLL if interrupts are not supported,
+ * or not desired for this PHY.  Set to PHY_IGNORE_INTERRUPT if
+ * the attached driver handles the interrupt
+ */
+#define PHY_POLL		-1
+#define PHY_IGNORE_INTERRUPT	-2
+
+#define PHY_HAS_INTERRUPT	0x00000001
+#define PHY_HAS_MAGICANEG	0x00000002
+
+#define MII_BUS_MAX 4
+
+
+#define PHY_INIT_TIMEOUT 100000
+#define PHY_STATE_TIME		1
+#define PHY_FORCE_TIMEOUT	10
+#define PHY_AN_TIMEOUT		10
+
+#define PHY_MAX_ADDR 32
+
+/* The Bus class for PHYs.  Devices which provide access to
+ * PHYs should register using this structure */
+struct mii_bus {
+	const char *name;
+	int id;
+	void *priv;
+	int (*read)(struct mii_bus *bus, int phy_id, int regnum);
+	int (*write)(struct mii_bus *bus, int phy_id, int regnum, u16 val);
+	int (*reset)(struct mii_bus *bus);
+
+	/* A lock to ensure that only one thing can read/write
+	 * the MDIO bus at a time */
+	spinlock_t mdio_lock;
+
+	struct device *dev;
+
+	/* list of all PHYs on bus */
+	struct phy_device *phy_map[PHY_MAX_ADDR];
+
+	/* Pointer to an array of interrupts, each PHY's
+	 * interrupt at the index matching its address */
+	int *irq;
+};
+
+#define PHY_INTERRUPT_DISABLED 0x0
+#define PHY_INTERRUPT_ENABLED 0x80000000
+
+/* PHY state machine states:
+ *
+ * DOWN: PHY device and driver are not ready for anything.  probe
+ * should be called if and only if the PHY is in this state,
+ * given that the PHY device exists.
+ * - PHY driver probe function will, depending on the PHY, set
+ * the state to STARTING or READY
+ *
+ * STARTING:  PHY device is coming up, and the ethernet driver is
+ * not ready.  PHY drivers may set this in the probe function.
+ * If they do, they are responsible for making sure the state is
+ * eventually set to indicate whether the PHY is UP or READY,
+ * depending on the state when the PHY is done starting up.
+ * - PHY driver will set the state to READY
+ * - start will set the state to PENDING
+ *
+ * READY: PHY is ready to send and receive packets, but the
+ * controller is not.  By default, PHYs which do not implement
+ * probe will be set to this state by phy_probe().  If the PHY
+ * driver knows the PHY is ready, and the PHY state is STARTING,
+ * then it sets this STATE.
+ * - start will set the state to UP
+ *
+ * PENDING: PHY device is coming up, but the ethernet driver is
+ * ready.  phy_start will set this state if the PHY state is
+ * STARTING.
+ * - PHY driver will set the state to UP when the PHY is ready
+ *
+ * UP: The PHY and attached device are ready to do work.
+ * Interrupts should be started here.
+ * - timer moves to AN
+ *
+ * AN: The PHY is currently negotiating the link state.  Link is
+ * therefore down for now.  phy_timer will set this state when it
+ * detects the state is UP.  config_aneg will set this state
+ * whenever called with phydev->autoneg set to AUTONEG_ENABLE.
+ * - If autonegotiation finishes, but there's no link, it sets
+ *   the state to NOLINK.
+ * - If aneg finishes with link, it sets the state to RUNNING,
+ *   and calls adjust_link
+ * - If autonegotiation did not finish after an arbitrary amount
+ *   of time, autonegotiation should be tried again if the PHY
+ *   supports "magic" autonegotiation (back to AN)
+ * - If it didn't finish, and no magic_aneg, move to FORCING.
+ *
+ * NOLINK: PHY is up, but not currently plugged in.
+ * - If the timer notes that the link comes back, we move to RUNNING
+ * - config_aneg moves to AN
+ * - phy_stop moves to HALTED
+ *
+ * FORCING: PHY is being configured with forced settings
+ * - if link is up, move to RUNNING
+ * - If link is down, we drop to the next highest setting, and
+ *   retry (FORCING) after a timeout
+ * - phy_stop moves to HALTED
+ *
+ * RUNNING: PHY is currently up, running, and possibly sending
+ * and/or receiving packets
+ * - timer will set CHANGELINK if we're polling (this ensures the
+ *   link state is polled every other cycle of this state machine,
+ *   which makes it every other second)
+ * - irq will set CHANGELINK
+ * - config_aneg will set AN
+ * - phy_stop moves to HALTED
+ *
+ * CHANGELINK: PHY experienced a change in link state
+ * - timer moves to RUNNING if link
+ * - timer moves to NOLINK if the link is down
+ * - phy_stop moves to HALTED
+ *
+ * HALTED: PHY is up, but no polling or interrupts are done. Or
+ * PHY is in an error state.
+ *
+ * - phy_start moves to RESUMING
+ *
+ * RESUMING: PHY was halted, but now wants to run again.
+ * - If we are forcing, or aneg is done, timer moves to RUNNING
+ * - If aneg is not done, timer moves to AN
+ * - phy_stop moves to HALTED
+ */
+enum phy_state {
+	PHY_DOWN=0,
+	PHY_STARTING,
+	PHY_READY,
+	PHY_PENDING,
+	PHY_UP,
+	PHY_AN,
+	PHY_RUNNING,
+	PHY_NOLINK,
+	PHY_FORCING,
+	PHY_CHANGELINK,
+	PHY_HALTED,
+	PHY_RESUMING
+};
+
+/* phy_device: An instance of a PHY
+ *
+ * drv: Pointer to the driver for this PHY instance
+ * bus: Pointer to the bus this PHY is on
+ * dev: driver model device structure for this PHY
+ * phy_id: UID for this device found during discovery
+ * state: state of the PHY for management purposes
+ * dev_flags: Device-specific flags used by the PHY driver.
+ * addr: Bus address of PHY
+ * link_timeout: The number of timer firings to wait before the
+ * giving up on the current attempt at acquiring a link
+ * irq: IRQ number of the PHY's interrupt (-1 if none)
+ * phy_timer: The timer for handling the state machine
+ * phy_queue: A work_queue for the interrupt
+ * attached_dev: The attached enet driver's device instance ptr
+ * adjust_link: Callback for the enet controller to respond to
+ * changes in the link state.
+ * adjust_state: Callback for the enet driver to respond to
+ * changes in the state machine.
+ *
+ * speed, duplex, pause, supported, advertising, and
+ * autoneg are used like in mii_if_info
+ *
+ * interrupts currently only supports enabled or disabled,
+ * but could be changed in the future to support enabling
+ * and disabling specific interrupts
+ *
+ * Contains some infrastructure for polling and interrupt
+ * handling, as well as handling shifts in PHY hardware state
+ */
+struct phy_device {
+	/* Information about the PHY type */
+	/* And management functions */
+	struct phy_driver *drv;
+
+	struct mii_bus *bus;
+
+	struct device dev;
+
+	u32 phy_id;
+
+	enum phy_state state;
+
+	u32 dev_flags;
+
+	/* Bus address of the PHY (0-32) */
+	int addr;
+
+	/* forced speed & duplex (no autoneg)
+	 * partner speed & duplex & pause (autoneg)
+	 */
+	int speed;
+	int duplex;
+	int pause;
+	int asym_pause;
+
+	/* The most recently read link state */
+	int link;
+
+	/* Enabled Interrupts */
+	u32 interrupts;
+
+	/* Union of PHY and Attached devices' supported modes */
+	/* See mii.h for more info */
+	u32 supported;
+	u32 advertising;
+
+	int autoneg;
+
+	int link_timeout;
+
+	/* Interrupt number for this PHY
+	 * -1 means no interrupt */
+	int irq;
+
+	/* private data pointer */
+	/* For use by PHYs to maintain extra state */
+	void *priv;
+
+	/* Interrupt and Polling infrastructure */
+	struct work_struct phy_queue;
+	struct timer_list phy_timer;
+
+	spinlock_t lock;
+
+	struct net_device *attached_dev;
+
+	void (*adjust_link)(struct net_device *dev);
+
+	void (*adjust_state)(struct net_device *dev);
+};
+#define to_phy_device(d) container_of(d, struct phy_device, dev)
+
+/* struct phy_driver: Driver structure for a particular PHY type
+ *
+ * phy_id: The result of reading the UID registers of this PHY
+ *   type, and ANDing them with the phy_id_mask.  This driver
+ *   only works for PHYs with IDs which match this field
+ * name: The friendly name of this PHY type
+ * phy_id_mask: Defines the important bits of the phy_id
+ * features: A list of features (speed, duplex, etc) supported
+ *   by this PHY
+ * flags: A bitfield defining certain other features this PHY
+ *   supports (like interrupts)
+ *
+ * The drivers must implement config_aneg and read_status.  All
+ * other functions are optional. Note that none of these
+ * functions should be called from interrupt time.  The goal is
+ * for the bus read/write functions to be able to block when the
+ * bus transaction is happening, and be freed up by an interrupt
+ * (The MPC85xx has this ability, though it is not currently
+ * supported in the driver).
+ */
+struct phy_driver {
+	u32 phy_id;
+	char *name;
+	unsigned int phy_id_mask;
+	u32 features;
+	u32 flags;
+
+	/* Called to initialize the PHY,
+	 * including after a reset */
+	int (*config_init)(struct phy_device *phydev);
+
+	/* Called during discovery.  Used to set
+	 * up device-specific structures, if any */
+	int (*probe)(struct phy_device *phydev);
+
+	/* PHY Power Management */
+	int (*suspend)(struct phy_device *phydev);
+	int (*resume)(struct phy_device *phydev);
+
+	/* Configures the advertisement and resets
+	 * autonegotiation if phydev->autoneg is on,
+	 * forces the speed to the current settings in phydev
+	 * if phydev->autoneg is off */
+	int (*config_aneg)(struct phy_device *phydev);
+
+	/* Determines the negotiated speed and duplex */
+	int (*read_status)(struct phy_device *phydev);
+
+	/* Clears any pending interrupts */
+	int (*ack_interrupt)(struct phy_device *phydev);
+
+	/* Enables or disables interrupts */
+	int (*config_intr)(struct phy_device *phydev);
+
+	/* Clears up any memory if needed */
+	void (*remove)(struct phy_device *phydev);
+
+	struct device_driver driver;
+};
+#define to_phy_driver(d) container_of(d, struct phy_driver, driver)
+
+int phy_read(struct phy_device *phydev, u16 regnum);
+int phy_write(struct phy_device *phydev, u16 regnum, u16 val);
+struct phy_device* get_phy_device(struct mii_bus *bus, int addr);
+int phy_clear_interrupt(struct phy_device *phydev);
+int phy_config_interrupt(struct phy_device *phydev, u32 interrupts);
+struct phy_device * phy_attach(struct net_device *dev,
+		const char *phy_id, u32 flags);
+struct phy_device * phy_connect(struct net_device *dev, const char *phy_id,
+		void (*handler)(struct net_device *), u32 flags);
+void phy_disconnect(struct phy_device *phydev);
+void phy_detach(struct phy_device *phydev);
+void phy_start(struct phy_device *phydev);
+void phy_stop(struct phy_device *phydev);
+int phy_start_aneg(struct phy_device *phydev);
+
+int mdiobus_register(struct mii_bus *bus);
+void mdiobus_unregister(struct mii_bus *bus);
+void phy_sanitize_settings(struct phy_device *phydev);
+int phy_stop_interrupts(struct phy_device *phydev);
+
+static inline int phy_read_status(struct phy_device *phydev) {
+	return phydev->drv->read_status(phydev);
+}
+
+int genphy_config_advert(struct phy_device *phydev);
+int genphy_setup_forced(struct phy_device *phydev);
+int genphy_restart_aneg(struct phy_device *phydev);
+int genphy_config_aneg(struct phy_device *phydev);
+int genphy_update_link(struct phy_device *phydev);
+int genphy_read_status(struct phy_device *phydev);
+void phy_driver_unregister(struct phy_driver *drv);
+int phy_driver_register(struct phy_driver *new_driver);
+void phy_prepare_link(struct phy_device *phydev,
+		void (*adjust_link)(struct net_device *));
+void phy_start_machine(struct phy_device *phydev,
+		void (*handler)(struct net_device *));
+void phy_stop_machine(struct phy_device *phydev);
+int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+int phy_mii_ioctl(struct phy_device *phydev,
+		struct mii_ioctl_data *mii_data, int cmd);
+int phy_start_interrupts(struct phy_device *phydev);
+void phy_print_status(struct phy_device *phydev);
+
+extern struct bus_type mdio_bus_type;
+#endif /* __PHY_H */
diff --git a/include/linux/serialP.h b/include/linux/serialP.h
index 2b2f35a64d75..2b9e6b9554d5 100644
--- a/include/linux/serialP.h
+++ b/include/linux/serialP.h
@@ -140,44 +140,4 @@ struct rs_multiport_struct {
 #define ALPHA_KLUDGE_MCR 0
 #endif
 
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK	0x0007
-#define SPCI_FL_BASE0	0x0000
-#define SPCI_FL_BASE1	0x0001
-#define SPCI_FL_BASE2	0x0002
-#define SPCI_FL_BASE3	0x0003
-#define SPCI_FL_BASE4	0x0004
-#define SPCI_FL_GET_BASE(x)	(x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK       (0x0007 << 4)
-#define SPCI_FL_IRQBASE0       (0x0000 << 4)
-#define SPCI_FL_IRQBASE1       (0x0001 << 4)
-#define SPCI_FL_IRQBASE2       (0x0002 << 4)
-#define SPCI_FL_IRQBASE3       (0x0003 << 4)
-#define SPCI_FL_IRQBASE4       (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x)        ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers), 
-   else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE	0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE	0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE	0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP	0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ	0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP		0x2000
-
-#define SPCI_FL_PNPDEFAULT	(SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
 #endif /* _LINUX_SERIAL_H */