diff options
| author | Codrin.Ciubotariu@microchip.com <Codrin.Ciubotariu@microchip.com> | 2020-01-07 14:17:47 +0300 |
|---|---|---|
| committer | Greg Kroah-Hartman <gregkh@linuxfoundation.org> | 2020-01-10 19:48:02 +0300 |
| commit | 477b8383100023ea0769979cff67e9be3a720397 (patch) | |
| tree | 002dff65ee4294d11765dbe136221181fda2534f /drivers/tty/serial/atmel_serial.c | |
| parent | 8e20fc3917117b42de316e87f073a1ca43d94c9f (diff) | |
| download | linux-477b8383100023ea0769979cff67e9be3a720397.tar.xz | |
tty/serial: atmel: RS485 & ISO7816: wait for TXRDY before sending data
At this moment, TXEMPTY is checked before sending data on RS485 and ISO7816
modes. However, TXEMPTY is risen when FIFO (if used) or the Transmit Shift
Register are empty, even though TXRDY might be up and controller is able to
receive data. Since the controller sends data only when TXEMPTY is ready,
on RS485, when DMA is not used, the RTS pin is driven low after each byte.
With this patch, the characters will be transmitted when TXRDY is up and
so, RTS pin will remain high between bytes.
The performance improvement on RS485 is about 8% with a baudrate of 300.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200107111656.26308-1-codrin.ciubotariu@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diffstat (limited to 'drivers/tty/serial/atmel_serial.c')
| -rw-r--r-- | drivers/tty/serial/atmel_serial.c | 26 |
1 files changed, 19 insertions, 7 deletions
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index fa19eb360ed8..0df666cffd4a 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -305,7 +305,11 @@ static int atmel_config_rs485(struct uart_port *port, if (rs485conf->flags & SER_RS485_ENABLED) { dev_dbg(port->dev, "Setting UART to RS485\n"); - atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; + if (port->rs485.flags & SER_RS485_RX_DURING_TX) + atmel_port->tx_done_mask = ATMEL_US_TXRDY; + else + atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; + atmel_uart_writel(port, ATMEL_US_TTGR, rs485conf->delay_rts_after_send); mode |= ATMEL_US_USMODE_RS485; @@ -823,7 +827,7 @@ static void atmel_tx_chars(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); if (port->x_char && - (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) { + (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) { atmel_uart_write_char(port, port->x_char); port->icount.tx++; port->x_char = 0; @@ -831,8 +835,7 @@ static void atmel_tx_chars(struct uart_port *port) if (uart_circ_empty(xmit) || uart_tx_stopped(port)) return; - while (atmel_uart_readl(port, ATMEL_US_CSR) & - atmel_port->tx_done_mask) { + while (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY) { atmel_uart_write_char(port, xmit->buf[xmit->tail]); xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); port->icount.tx++; @@ -843,10 +846,20 @@ static void atmel_tx_chars(struct uart_port *port) if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) uart_write_wakeup(port); - if (!uart_circ_empty(xmit)) + if (!uart_circ_empty(xmit)) { + /* we still have characters to transmit, so we should continue + * transmitting them when TX is ready, regardless of + * mode or duplexity + */ + atmel_port->tx_done_mask |= ATMEL_US_TXRDY; + /* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); + } else { + if (atmel_uart_is_half_duplex(port)) + atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY; + } } static void atmel_complete_tx_dma(void *arg) @@ -2518,8 +2531,7 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port, * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or * ENDTX|TXBUFE */ - if (port->rs485.flags & SER_RS485_ENABLED || - port->iso7816.flags & SER_ISO7816_ENABLED) + if (atmel_uart_is_half_duplex(port)) atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; else if (atmel_use_pdc_tx(port)) { port->fifosize = PDC_BUFFER_SIZE; |