wlcore: spi: add wl18xx support

Add support for using with both wl12xx and wl18xx.

- all wilink family needs special init command for entering wspi mode.
  extra clock cycles should be sent after the spi init command while the
  cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
  completes the init stage.

Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

1 files changed, 105 insertions, 18 deletions

diff --git a/drivers/net/wireless/ti/wlcore/spi.c b/drivers/net/wireless/ti/wlcore/spi.c
index cea9443c22a6..73fbcf15545c 100644
--- a/drivers/net/wireless/ti/wlcore/spi.c
+++ b/drivers/net/wireless/ti/wlcore/spi.c
@@ -70,16 +70,30 @@
 #define WSPI_MAX_CHUNK_SIZE    4092
 
 /*
- * only support SPI for 12xx - this code should be reworked when 18xx
- * support is introduced
+ * wl18xx driver aggregation buffer size is (13 * PAGE_SIZE) compared to
+ * (4 * PAGE_SIZE) for wl12xx, so use the larger buffer needed for wl18xx
  */
-#define SPI_AGGR_BUFFER_SIZE (4 * PAGE_SIZE)
+#define SPI_AGGR_BUFFER_SIZE (13 * PAGE_SIZE)
 
 /* Maximum number of SPI write chunks */
 #define WSPI_MAX_NUM_OF_CHUNKS \
 	((SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) + 1)
 
 
+struct wilink_familiy_data {
+	char name[8];
+};
+
+const struct wilink_familiy_data *wilink_data;
+
+static const struct wilink_familiy_data wl18xx_data = {
+	.name = "wl18xx",
+};
+
+static const struct wilink_familiy_data wl12xx_data = {
+	.name = "wl12xx",
+};
+
 struct wl12xx_spi_glue {
 	struct device *dev;
 	struct platform_device *core;
@@ -119,6 +133,7 @@ static void wl12xx_spi_init(struct device *child)
 	struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent);
 	struct spi_transfer t;
 	struct spi_message m;
+	struct spi_device *spi = to_spi_device(glue->dev);
 	u8 *cmd = kzalloc(WSPI_INIT_CMD_LEN, GFP_KERNEL);
 
 	if (!cmd) {
@@ -151,6 +166,7 @@ static void wl12xx_spi_init(struct device *child)
 		cmd[6] |= WSPI_INIT_CMD_EN_FIXEDBUSY;
 
 	cmd[7] = crc7_be(0, cmd+2, WSPI_INIT_CMD_CRC_LEN) | WSPI_INIT_CMD_END;
+
 	/*
 	 * The above is the logical order; it must actually be stored
 	 * in the buffer byte-swapped.
@@ -163,6 +179,28 @@ static void wl12xx_spi_init(struct device *child)
 	spi_message_add_tail(&t, &m);
 
 	spi_sync(to_spi_device(glue->dev), &m);
+
+	/* Send extra clocks with inverted CS (high). this is required
+	 * by the wilink family in order to successfully enter WSPI mode.
+	 */
+	spi->mode ^= SPI_CS_HIGH;
+	memset(&m, 0, sizeof(m));
+	spi_message_init(&m);
+
+	cmd[0] = 0xff;
+	cmd[1] = 0xff;
+	cmd[2] = 0xff;
+	cmd[3] = 0xff;
+	__swab32s((u32 *)cmd);
+
+	t.tx_buf = cmd;
+	t.len = 4;
+	spi_message_add_tail(&t, &m);
+
+	spi_sync(to_spi_device(glue->dev), &m);
+
+	/* Restore chip select configration to normal */
+	spi->mode ^= SPI_CS_HIGH;
 	kfree(cmd);
 }
 
@@ -270,22 +308,25 @@ static int __must_check wl12xx_spi_raw_read(struct device *child, int addr,
 	return 0;
 }
 
-static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
-					     void *buf, size_t len, bool fixed)
+static int __wl12xx_spi_raw_write(struct device *child, int addr,
+				  void *buf, size_t len, bool fixed)
 {
 	struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent);
-	/* SPI write buffers - 2 for each chunk */
-	struct spi_transfer t[2 * WSPI_MAX_NUM_OF_CHUNKS];
+	struct spi_transfer *t;
 	struct spi_message m;
 	u32 commands[WSPI_MAX_NUM_OF_CHUNKS]; /* 1 command per chunk */
 	u32 *cmd;
 	u32 chunk_len;
 	int i;
 
+	/* SPI write buffers - 2 for each chunk */
+	t = kzalloc(sizeof(*t) * 2 * WSPI_MAX_NUM_OF_CHUNKS, GFP_KERNEL);
+	if (!t)
+		return -ENOMEM;
+
 	WARN_ON(len > SPI_AGGR_BUFFER_SIZE);
 
 	spi_message_init(&m);
-	memset(t, 0, sizeof(t));
 
 	cmd = &commands[0];
 	i = 0;
@@ -318,9 +359,26 @@ static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
 
 	spi_sync(to_spi_device(glue->dev), &m);
 
+	kfree(t);
 	return 0;
 }
 
+static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
+					     void *buf, size_t len, bool fixed)
+{
+	int ret;
+
+	/* The ELP wakeup write may fail the first time due to internal
+	 * hardware latency. It is safer to send the wakeup command twice to
+	 * avoid unexpected failures.
+	 */
+	if (addr == HW_ACCESS_ELP_CTRL_REG)
+		ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed);
+	ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed);
+
+	return ret;
+}
+
 /**
  * wl12xx_spi_set_power - power on/off the wl12xx unit
  * @child: wl12xx device handle.
@@ -349,17 +407,38 @@ static int wl12xx_spi_set_power(struct device *child, bool enable)
 	return ret;
 }
 
+/**
+ * wl12xx_spi_set_block_size
+ *
+ * This function is not needed for spi mode, but need to be present.
+ * Without it defined the wlcore fallback to use the wrong packet
+ * allignment on tx.
+ */
+static void wl12xx_spi_set_block_size(struct device *child,
+				      unsigned int blksz)
+{
+}
+
 static struct wl1271_if_operations spi_ops = {
 	.read		= wl12xx_spi_raw_read,
 	.write		= wl12xx_spi_raw_write,
 	.reset		= wl12xx_spi_reset,
 	.init		= wl12xx_spi_init,
 	.power		= wl12xx_spi_set_power,
-	.set_block_size = NULL,
+	.set_block_size = wl12xx_spi_set_block_size,
 };
 
 static const struct of_device_id wlcore_spi_of_match_table[] = {
-	{ .compatible = "ti,wl1271" },
+	{ .compatible = "ti,wl1271", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1273", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1281", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1283", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1801", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1805", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1807", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1831", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1835", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1837", .data = &wl18xx_data},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table);
@@ -376,17 +455,24 @@ static int wlcore_probe_of(struct spi_device *spi, struct wl12xx_spi_glue *glue,
 {
 	struct device_node *dt_node = spi->dev.of_node;
 	int ret;
+	const struct of_device_id *of_id;
+
+	of_id = of_match_node(wlcore_spi_of_match_table, dt_node);
+	if (!of_id)
+		return -ENODEV;
+
+	wilink_data = of_id->data;
+	dev_info(&spi->dev, "selected chip familiy is %s\n",
+		 wilink_data->name);
 
 	if (of_find_property(dt_node, "clock-xtal", NULL))
 		pdev_data->ref_clock_xtal = true;
 
-	ret = of_property_read_u32(dt_node, "ref-clock-frequency",
-				   &pdev_data->ref_clock_freq);
-	if (ret) {
-		dev_err(glue->dev,
-			"can't get reference clock frequency (%d)\n", ret);
-		return ret;
-	}
+	/* optional clock frequency params */
+	of_property_read_u32(dt_node, "ref-clock-frequency",
+			     &pdev_data->ref_clock_freq);
+	of_property_read_u32(dt_node, "tcxo-clock-frequency",
+			     &pdev_data->tcxo_clock_freq);
 
 	return 0;
 }
@@ -437,7 +523,8 @@ static int wl1271_probe(struct spi_device *spi)
 		return ret;
 	}
 
-	glue->core = platform_device_alloc("wl12xx", PLATFORM_DEVID_AUTO);
+	glue->core = platform_device_alloc(wilink_data->name,
+					   PLATFORM_DEVID_AUTO);
 	if (!glue->core) {
 		dev_err(glue->dev, "can't allocate platform_device\n");
 		return -ENOMEM;