Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Highlights:

   1) Support SPI based w5100 devices, from Akinobu Mita.

   2) Partial Segmentation Offload, from Alexander Duyck.

   3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.

   4) Allow cls_flower stats offload, from Amir Vadai.

   5) Implement bpf blinding, from Daniel Borkmann.

   6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
      actually using FASYNC these atomics are superfluous.  From Eric
      Dumazet.

   7) Run TCP more preemptibly, also from Eric Dumazet.

   8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
      driver, from Gal Pressman.

   9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.

  10) Improve BPF usage documentation, from Jesper Dangaard Brouer.

  11) Support tunneling offloads in qed, from Manish Chopra.

  12) aRFS offloading in mlx5e, from Maor Gottlieb.

  13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
      Leitner.

  14) Add MSG_EOR support to TCP, this allows controlling packet
      coalescing on application record boundaries for more accurate
      socket timestamp sampling.  From Martin KaFai Lau.

  15) Fix alignment of 64-bit netlink attributes across the board, from
      Nicolas Dichtel.

  16) Per-vlan stats in bridging, from Nikolay Aleksandrov.

  17) Several conversions of drivers to ethtool ksettings, from Philippe
      Reynes.

  18) Checksum neutral ILA in ipv6, from Tom Herbert.

  19) Factorize all of the various marvell dsa drivers into one, from
      Vivien Didelot

  20) Add VF support to qed driver, from Yuval Mintz"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
  Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
  Revert "phy dp83867: Make rgmii parameters optional"
  r8169: default to 64-bit DMA on recent PCIe chips
  phy dp83867: Make rgmii parameters optional
  phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
  bpf: arm64: remove callee-save registers use for tmp registers
  asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
  switchdev: pass pointer to fib_info instead of copy
  net_sched: close another race condition in tcf_mirred_release()
  tipc: fix nametable publication field in nl compat
  drivers: net: Don't print unpopulated net_device name
  qed: add support for dcbx.
  ravb: Add missing free_irq() calls to ravb_close()
  qed: Remove a stray tab
  net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
  net: ethernet: fec-mpc52xx: use phydev from struct net_device
  bpf, doc: fix typo on bpf_asm descriptions
  stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
  net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
  net: ethernet: fs-enet: use phydev from struct net_device
  ...

1 files changed, 16 insertions, 16 deletions

diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index 0fce1c76638e..641b13a279e1 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -75,13 +75,13 @@
 /**
  * ath5k_hw_radio_revision() - Get the PHY Chip revision
  * @ah: The &struct ath5k_hw
- * @band: One of enum ieee80211_band
+ * @band: One of enum nl80211_band
  *
  * Returns the revision number of a 2GHz, 5GHz or single chip
  * radio.
  */
 u16
-ath5k_hw_radio_revision(struct ath5k_hw *ah, enum ieee80211_band band)
+ath5k_hw_radio_revision(struct ath5k_hw *ah, enum nl80211_band band)
 {
 	unsigned int i;
 	u32 srev;
@@ -91,10 +91,10 @@ ath5k_hw_radio_revision(struct ath5k_hw *ah, enum ieee80211_band band)
 	 * Set the radio chip access register
 	 */
 	switch (band) {
-	case IEEE80211_BAND_2GHZ:
+	case NL80211_BAND_2GHZ:
 		ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_2GHZ, AR5K_PHY(0));
 		break;
-	case IEEE80211_BAND_5GHZ:
+	case NL80211_BAND_5GHZ:
 		ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0));
 		break;
 	default:
@@ -138,11 +138,11 @@ ath5k_channel_ok(struct ath5k_hw *ah, struct ieee80211_channel *channel)
 	u16 freq = channel->center_freq;
 
 	/* Check if the channel is in our supported range */
-	if (channel->band == IEEE80211_BAND_2GHZ) {
+	if (channel->band == NL80211_BAND_2GHZ) {
 		if ((freq >= ah->ah_capabilities.cap_range.range_2ghz_min) &&
 		    (freq <= ah->ah_capabilities.cap_range.range_2ghz_max))
 			return true;
-	} else if (channel->band == IEEE80211_BAND_5GHZ)
+	} else if (channel->band == NL80211_BAND_5GHZ)
 		if ((freq >= ah->ah_capabilities.cap_range.range_5ghz_min) &&
 		    (freq <= ah->ah_capabilities.cap_range.range_5ghz_max))
 			return true;
@@ -743,7 +743,7 @@ done:
 /**
  * ath5k_hw_rfgain_init() - Write initial RF gain settings to hw
  * @ah: The &struct ath5k_hw
- * @band: One of enum ieee80211_band
+ * @band: One of enum nl80211_band
  *
  * Write initial RF gain table to set the RF sensitivity.
  *
@@ -751,7 +751,7 @@ done:
  * with Gain_F calibration
  */
 static int
-ath5k_hw_rfgain_init(struct ath5k_hw *ah, enum ieee80211_band band)
+ath5k_hw_rfgain_init(struct ath5k_hw *ah, enum nl80211_band band)
 {
 	const struct ath5k_ini_rfgain *ath5k_rfg;
 	unsigned int i, size, index;
@@ -786,7 +786,7 @@ ath5k_hw_rfgain_init(struct ath5k_hw *ah, enum ieee80211_band band)
 		return -EINVAL;
 	}
 
-	index = (band == IEEE80211_BAND_2GHZ) ? 1 : 0;
+	index = (band == NL80211_BAND_2GHZ) ? 1 : 0;
 
 	for (i = 0; i < size; i++) {
 		AR5K_REG_WAIT(i);
@@ -917,7 +917,7 @@ ath5k_hw_rfregs_init(struct ath5k_hw *ah,
 	}
 
 	/* Set Output and Driver bias current (OB/DB) */
-	if (channel->band == IEEE80211_BAND_2GHZ) {
+	if (channel->band == NL80211_BAND_2GHZ) {
 
 		if (channel->hw_value == AR5K_MODE_11B)
 			ee_mode = AR5K_EEPROM_MODE_11B;
@@ -944,7 +944,7 @@ ath5k_hw_rfregs_init(struct ath5k_hw *ah,
 						AR5K_RF_DB_2GHZ, true);
 
 	/* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */
-	} else if ((channel->band == IEEE80211_BAND_5GHZ) ||
+	} else if ((channel->band == NL80211_BAND_5GHZ) ||
 			(ah->ah_radio == AR5K_RF5111)) {
 
 		/* For 11a, Turbo and XR we need to choose
@@ -1145,7 +1145,7 @@ ath5k_hw_rfregs_init(struct ath5k_hw *ah,
 	}
 
 	if (ah->ah_radio == AR5K_RF5413 &&
-	channel->band == IEEE80211_BAND_2GHZ) {
+	channel->band == NL80211_BAND_2GHZ) {
 
 		ath5k_hw_rfb_op(ah, rf_regs, 1, AR5K_RF_DERBY_CHAN_SEL_MODE,
 									true);
@@ -1270,7 +1270,7 @@ ath5k_hw_rf5111_channel(struct ath5k_hw *ah,
 	 */
 	data0 = data1 = 0;
 
-	if (channel->band == IEEE80211_BAND_2GHZ) {
+	if (channel->band == NL80211_BAND_2GHZ) {
 		/* Map 2GHz channel to 5GHz Atheros channel ID */
 		ret = ath5k_hw_rf5111_chan2athchan(
 			ieee80211_frequency_to_channel(channel->center_freq),
@@ -1446,7 +1446,7 @@ ath5k_hw_channel(struct ath5k_hw *ah,
 			"channel frequency (%u MHz) out of supported "
 			"band range\n",
 			channel->center_freq);
-			return -EINVAL;
+		return -EINVAL;
 	}
 
 	/*
@@ -1919,7 +1919,7 @@ ath5k_hw_set_spur_mitigation_filter(struct ath5k_hw *ah,
 	/* Convert current frequency to fbin value (the same way channels
 	 * are stored on EEPROM, check out ath5k_eeprom_bin2freq) and scale
 	 * up by 2 so we can compare it later */
-	if (channel->band == IEEE80211_BAND_2GHZ) {
+	if (channel->band == NL80211_BAND_2GHZ) {
 		chan_fbin = (channel->center_freq - 2300) * 10;
 		freq_band = AR5K_EEPROM_BAND_2GHZ;
 	} else {
@@ -1983,7 +1983,7 @@ ath5k_hw_set_spur_mitigation_filter(struct ath5k_hw *ah,
 			symbol_width = AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz / 4;
 			break;
 		default:
-			if (channel->band == IEEE80211_BAND_5GHZ) {
+			if (channel->band == NL80211_BAND_5GHZ) {
 				/* Both sample_freq and chip_freq are 40MHz */
 				spur_delta_phase = (spur_offset << 17) / 25;
 				spur_freq_sigma_delta =