ewrk3/tulip: Move the DEC - Tulip drivers

Move the DEC - Tulip driver into drivers/net/ethernet/dec/tulip/
and make the necessary Kconfig and Makefile changes.

The Digital Equioment (DEC) driver ewrk3 was moved into
drivers/net/ethernet/dec/ and the remaining drivers (Tulip)
were moved into drivers/net/ethernet/dec/tulip/

CC: Tobias Ringstrom <tori@unhappy.mine.nu>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: David Davies <davies@maniac.ultranet.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>

1 files changed, 0 insertions, 171 deletions

diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig
deleted file mode 100644
index 1f8d4a8d8ea4..000000000000
--- a/drivers/net/tulip/Kconfig
+++ /dev/null
@@ -1,171 +0,0 @@
-#
-# Tulip family network device configuration
-#
-
-menuconfig NET_TULIP
-	bool "\"Tulip\" family network device support"
-	depends on PCI || EISA || CARDBUS
-	help
-	  This selects the "Tulip" family of EISA/PCI network cards.
-
-if NET_TULIP
-
-config DE2104X
-	tristate "Early DECchip Tulip (dc2104x) PCI support"
-	depends on PCI
-	select CRC32
-	---help---
-	  This driver is developed for the SMC EtherPower series Ethernet
-	  cards and also works with cards based on the DECchip
-	  21040 (Tulip series) chips.  Some LinkSys PCI cards are
-	  of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
-	  (smc9332dst), you can also try the driver for "Generic DECchip"
-	  cards, below.  However, most people with a network card of this type
-	  will say Y here.) Do read the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
-	  To compile this driver as a module, choose M here. The module will
-	  be called de2104x.
-
-config DE2104X_DSL
-	int "Descriptor Skip Length in 32 bit longwords"
-	depends on DE2104X
-	range 0 31
-	default 0
-	help
-	  Setting this value allows to align ring buffer descriptors into their
-	  own cache lines. Value of 4 corresponds to the typical 32 byte line
-	  (the descriptor is 16 bytes). This is necessary on systems that lack
-	  cache coherence, an example is PowerMac 5500. Otherwise 0 is safe.
-	  Default is 0, and range is 0 to 31.
-
-config TULIP
-	tristate "DECchip Tulip (dc2114x) PCI support"
-	depends on PCI
-	select CRC32
-	---help---
-	  This driver is developed for the SMC EtherPower series Ethernet
-	  cards and also works with cards based on the DECchip 
-	  21140 (Tulip series) chips.  Some LinkSys PCI cards are
-	  of this type.  (If your card is NOT SMC EtherPower 10/100 PCI
-	  (smc9332dst), you can also try the driver for "Generic DECchip"
-	  cards, above.  However, most people with a network card of this type
-	  will say Y here.) Do read the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
-	  To compile this driver as a module, choose M here. The module will
-	  be called tulip.
-
-config TULIP_MWI
-	bool "New bus configuration (EXPERIMENTAL)"
-	depends on TULIP && EXPERIMENTAL
-	help
-	  This configures your Tulip card specifically for the card and
-	  system cache line size type you are using.
-
-	  This is experimental code, not yet tested on many boards.
-
-	  If unsure, say N.
-
-config TULIP_MMIO
-	bool "Use PCI shared mem for NIC registers"
-	depends on TULIP
-	help
-	  Use PCI shared memory for the NIC registers, rather than going through
-	  the Tulip's PIO (programmed I/O ports).  Faster, but could produce
-	  obscure bugs if your mainboard has memory controller timing issues.
-	  If in doubt, say N.
-
-config TULIP_NAPI
-	bool "Use RX polling (NAPI)"
-	depends on TULIP
-	help
-	  NAPI is a new driver API designed to reduce CPU and interrupt load
-	  when the driver is receiving lots of packets from the card. It is
-	  still somewhat experimental and thus not yet enabled by default.
-
-	  If your estimated Rx load is 10kpps or more, or if the card will be
-	  deployed on potentially unfriendly networks (e.g. in a firewall),
-	  then say Y here.
-
-	  If in doubt, say N.
-
-config TULIP_NAPI_HW_MITIGATION
-	bool "Use Interrupt Mitigation"
-	depends on TULIP_NAPI
-	---help---
-	  Use HW to reduce RX interrupts. Not strictly necessary since NAPI
-	  reduces RX interrupts by itself. Interrupt mitigation reduces RX
-	  interrupts even at low levels of traffic at the cost of a small
-	  latency.
-
-	  If in doubt, say Y.
-
-config TULIP_DM910X
-	def_bool y
-	depends on TULIP && SPARC
-
-config DE4X5
-	tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
-	depends on PCI || EISA
-	select CRC32
-	---help---
-	  This is support for the DIGITAL series of PCI/EISA Ethernet cards.
-	  These include the DE425, DE434, DE435, DE450 and DE500 models.  If
-	  you have a network card of this type, say Y and read the
-	  Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>. More specific
-	  information is contained in
-	  <file:Documentation/networking/de4x5.txt>.
-
-	  To compile this driver as a module, choose M here. The module will
-	  be called de4x5.
-
-config WINBOND_840
-	tristate "Winbond W89c840 Ethernet support"
-	depends on PCI
-	select CRC32
-	select MII
-	help
-	  This driver is for the Winbond W89c840 chip.  It also works with 
-	  the TX9882 chip on the Compex RL100-ATX board.
-	  More specific information and updates are available from
-	  <http://www.scyld.com/network/drivers.html>.
-
-config DM9102
-	tristate "Davicom DM910x/DM980x support"
-	depends on PCI
-	select CRC32
-	---help---
-	  This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
-	  Davicom (<http://www.davicom.com.tw/>).  If you have such a network
-	  (Ethernet) card, say Y.  Some information is contained in the file
-	  <file:Documentation/networking/dmfe.txt>.
-
-	  To compile this driver as a module, choose M here. The module will
-	  be called dmfe.
-
-config ULI526X
-	tristate "ULi M526x controller support"
-	depends on PCI
-	select CRC32
-	---help---
-	  This driver is for ULi M5261/M5263 10/100M Ethernet Controller
-	  (<http://www.nvidia.com/page/uli_drivers.html>).
-
-	  To compile this driver as a module, choose M here. The module will
-	  be called uli526x.
-	  
-config PCMCIA_XIRCOM
-	tristate "Xircom CardBus support"
-	depends on CARDBUS
-	---help---
-	  This driver is for the Digital "Tulip" Ethernet CardBus adapters.
-	  It should work with most DEC 21*4*-based chips/ethercards, as well
-	  as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
-	  ASIX.
-
-	  To compile this driver as a module, choose M here. The module will
-	  be called xircom_cb.  If unsure, say N.
-
-endif # NET_TULIP