Merge branch 'power-supply-scope' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen

1 files changed, 777 insertions, 0 deletions

diff --git a/drivers/net/ethernet/sfc/falcon_boards.c b/drivers/net/ethernet/sfc/falcon_boards.c
new file mode 100644
index 000000000000..6cc16b8cc6f4
--- /dev/null
+++ b/drivers/net/ethernet/sfc/falcon_boards.c
@@ -0,0 +1,777 @@
+/****************************************************************************
+ * Driver for Solarflare Solarstorm network controllers and boards
+ * Copyright 2007-2010 Solarflare Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation, incorporated herein by reference.
+ */
+
+#include <linux/rtnetlink.h>
+
+#include "net_driver.h"
+#include "phy.h"
+#include "efx.h"
+#include "nic.h"
+#include "workarounds.h"
+
+/* Macros for unpacking the board revision */
+/* The revision info is in host byte order. */
+#define FALCON_BOARD_TYPE(_rev) (_rev >> 8)
+#define FALCON_BOARD_MAJOR(_rev) ((_rev >> 4) & 0xf)
+#define FALCON_BOARD_MINOR(_rev) (_rev & 0xf)
+
+/* Board types */
+#define FALCON_BOARD_SFE4001 0x01
+#define FALCON_BOARD_SFE4002 0x02
+#define FALCON_BOARD_SFE4003 0x03
+#define FALCON_BOARD_SFN4112F 0x52
+
+/* Board temperature is about 15°C above ambient when air flow is
+ * limited.  The maximum acceptable ambient temperature varies
+ * depending on the PHY specifications but the critical temperature
+ * above which we should shut down to avoid damage is 80°C. */
+#define FALCON_BOARD_TEMP_BIAS	15
+#define FALCON_BOARD_TEMP_CRIT	(80 + FALCON_BOARD_TEMP_BIAS)
+
+/* SFC4000 datasheet says: 'The maximum permitted junction temperature
+ * is 125°C; the thermal design of the environment for the SFC4000
+ * should aim to keep this well below 100°C.' */
+#define FALCON_JUNC_TEMP_MIN	0
+#define FALCON_JUNC_TEMP_MAX	90
+#define FALCON_JUNC_TEMP_CRIT	125
+
+/*****************************************************************************
+ * Support for LM87 sensor chip used on several boards
+ */
+#define LM87_REG_TEMP_HW_INT_LOCK	0x13
+#define LM87_REG_TEMP_HW_EXT_LOCK	0x14
+#define LM87_REG_TEMP_HW_INT		0x17
+#define LM87_REG_TEMP_HW_EXT		0x18
+#define LM87_REG_TEMP_EXT1		0x26
+#define LM87_REG_TEMP_INT		0x27
+#define LM87_REG_ALARMS1		0x41
+#define LM87_REG_ALARMS2		0x42
+#define LM87_IN_LIMITS(nr, _min, _max)			\
+	0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min
+#define LM87_AIN_LIMITS(nr, _min, _max)			\
+	0x3B + (nr), _max, 0x1A + (nr), _min
+#define LM87_TEMP_INT_LIMITS(_min, _max)		\
+	0x39, _max, 0x3A, _min
+#define LM87_TEMP_EXT1_LIMITS(_min, _max)		\
+	0x37, _max, 0x38, _min
+
+#define LM87_ALARM_TEMP_INT		0x10
+#define LM87_ALARM_TEMP_EXT1		0x20
+
+#if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE)
+
+static int efx_poke_lm87(struct i2c_client *client, const u8 *reg_values)
+{
+	while (*reg_values) {
+		u8 reg = *reg_values++;
+		u8 value = *reg_values++;
+		int rc = i2c_smbus_write_byte_data(client, reg, value);
+		if (rc)
+			return rc;
+	}
+	return 0;
+}
+
+static const u8 falcon_lm87_common_regs[] = {
+	LM87_REG_TEMP_HW_INT_LOCK, FALCON_BOARD_TEMP_CRIT,
+	LM87_REG_TEMP_HW_INT, FALCON_BOARD_TEMP_CRIT,
+	LM87_TEMP_EXT1_LIMITS(FALCON_JUNC_TEMP_MIN, FALCON_JUNC_TEMP_MAX),
+	LM87_REG_TEMP_HW_EXT_LOCK, FALCON_JUNC_TEMP_CRIT,
+	LM87_REG_TEMP_HW_EXT, FALCON_JUNC_TEMP_CRIT,
+	0
+};
+
+static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
+			 const u8 *reg_values)
+{
+	struct falcon_board *board = falcon_board(efx);
+	struct i2c_client *client = i2c_new_device(&board->i2c_adap, info);
+	int rc;
+
+	if (!client)
+		return -EIO;
+
+	/* Read-to-clear alarm/interrupt status */
+	i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
+	i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
+
+	rc = efx_poke_lm87(client, reg_values);
+	if (rc)
+		goto err;
+	rc = efx_poke_lm87(client, falcon_lm87_common_regs);
+	if (rc)
+		goto err;
+
+	board->hwmon_client = client;
+	return 0;
+
+err:
+	i2c_unregister_device(client);
+	return rc;
+}
+
+static void efx_fini_lm87(struct efx_nic *efx)
+{
+	i2c_unregister_device(falcon_board(efx)->hwmon_client);
+}
+
+static int efx_check_lm87(struct efx_nic *efx, unsigned mask)
+{
+	struct i2c_client *client = falcon_board(efx)->hwmon_client;
+	bool temp_crit, elec_fault, is_failure;
+	u16 alarms;
+	s32 reg;
+
+	/* If link is up then do not monitor temperature */
+	if (EFX_WORKAROUND_7884(efx) && efx->link_state.up)
+		return 0;
+
+	reg = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
+	if (reg < 0)
+		return reg;
+	alarms = reg;
+	reg = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
+	if (reg < 0)
+		return reg;
+	alarms |= reg << 8;
+	alarms &= mask;
+
+	temp_crit = false;
+	if (alarms & LM87_ALARM_TEMP_INT) {
+		reg = i2c_smbus_read_byte_data(client, LM87_REG_TEMP_INT);
+		if (reg < 0)
+			return reg;
+		if (reg > FALCON_BOARD_TEMP_CRIT)
+			temp_crit = true;
+	}
+	if (alarms & LM87_ALARM_TEMP_EXT1) {
+		reg = i2c_smbus_read_byte_data(client, LM87_REG_TEMP_EXT1);
+		if (reg < 0)
+			return reg;
+		if (reg > FALCON_JUNC_TEMP_CRIT)
+			temp_crit = true;
+	}
+	elec_fault = alarms & ~(LM87_ALARM_TEMP_INT | LM87_ALARM_TEMP_EXT1);
+	is_failure = temp_crit || elec_fault;
+
+	if (alarms)
+		netif_err(efx, hw, efx->net_dev,
+			  "LM87 detected a hardware %s (status %02x:%02x)"
+			  "%s%s%s%s\n",
+			  is_failure ? "failure" : "problem",
+			  alarms & 0xff, alarms >> 8,
+			  (alarms & LM87_ALARM_TEMP_INT) ?
+			  "; board is overheating" : "",
+			  (alarms & LM87_ALARM_TEMP_EXT1) ?
+			  "; controller is overheating" : "",
+			  temp_crit ? "; reached critical temperature" : "",
+			  elec_fault ? "; electrical fault" : "");
+
+	return is_failure ? -ERANGE : 0;
+}
+
+#else /* !CONFIG_SENSORS_LM87 */
+
+static inline int
+efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
+	      const u8 *reg_values)
+{
+	return 0;
+}
+static inline void efx_fini_lm87(struct efx_nic *efx)
+{
+}
+static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask)
+{
+	return 0;
+}
+
+#endif /* CONFIG_SENSORS_LM87 */
+
+/*****************************************************************************
+ * Support for the SFE4001 NIC.
+ *
+ * The SFE4001 does not power-up fully at reset due to its high power
+ * consumption.  We control its power via a PCA9539 I/O expander.
+ * It also has a MAX6647 temperature monitor which we expose to
+ * the lm90 driver.
+ *
+ * This also provides minimal support for reflashing the PHY, which is
+ * initiated by resetting it with the FLASH_CFG_1 pin pulled down.
+ * On SFE4001 rev A2 and later this is connected to the 3V3X output of
+ * the IO-expander.
+ * We represent reflash mode as PHY_MODE_SPECIAL and make it mutually
+ * exclusive with the network device being open.
+ */
+
+/**************************************************************************
+ * Support for I2C IO Expander device on SFE4001
+ */
+#define	PCA9539 0x74
+
+#define	P0_IN 0x00
+#define	P0_OUT 0x02
+#define	P0_INVERT 0x04
+#define	P0_CONFIG 0x06
+
+#define	P0_EN_1V0X_LBN 0
+#define	P0_EN_1V0X_WIDTH 1
+#define	P0_EN_1V2_LBN 1
+#define	P0_EN_1V2_WIDTH 1
+#define	P0_EN_2V5_LBN 2
+#define	P0_EN_2V5_WIDTH 1
+#define	P0_EN_3V3X_LBN 3
+#define	P0_EN_3V3X_WIDTH 1
+#define	P0_EN_5V_LBN 4
+#define	P0_EN_5V_WIDTH 1
+#define	P0_SHORTEN_JTAG_LBN 5
+#define	P0_SHORTEN_JTAG_WIDTH 1
+#define	P0_X_TRST_LBN 6
+#define	P0_X_TRST_WIDTH 1
+#define	P0_DSP_RESET_LBN 7
+#define	P0_DSP_RESET_WIDTH 1
+
+#define	P1_IN 0x01
+#define	P1_OUT 0x03
+#define	P1_INVERT 0x05
+#define	P1_CONFIG 0x07
+
+#define	P1_AFE_PWD_LBN 0
+#define	P1_AFE_PWD_WIDTH 1
+#define	P1_DSP_PWD25_LBN 1
+#define	P1_DSP_PWD25_WIDTH 1
+#define	P1_RESERVED_LBN 2
+#define	P1_RESERVED_WIDTH 2
+#define	P1_SPARE_LBN 4
+#define	P1_SPARE_WIDTH 4
+
+/* Temperature Sensor */
+#define MAX664X_REG_RSL		0x02
+#define MAX664X_REG_WLHO	0x0B
+
+static void sfe4001_poweroff(struct efx_nic *efx)
+{
+	struct i2c_client *ioexp_client = falcon_board(efx)->ioexp_client;
+	struct i2c_client *hwmon_client = falcon_board(efx)->hwmon_client;
+
+	/* Turn off all power rails and disable outputs */
+	i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
+	i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
+	i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);
+
+	/* Clear any over-temperature alert */
+	i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
+}
+
+static int sfe4001_poweron(struct efx_nic *efx)
+{
+	struct i2c_client *ioexp_client = falcon_board(efx)->ioexp_client;
+	struct i2c_client *hwmon_client = falcon_board(efx)->hwmon_client;
+	unsigned int i, j;
+	int rc;
+	u8 out;
+
+	/* Clear any previous over-temperature alert */
+	rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
+	if (rc < 0)
+		return rc;
+
+	/* Enable port 0 and port 1 outputs on IO expander */
+	rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
+	if (rc)
+		return rc;
+	rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
+				       0xff & ~(1 << P1_SPARE_LBN));
+	if (rc)
+		goto fail_on;
+
+	/* If PHY power is on, turn it all off and wait 1 second to
+	 * ensure a full reset.
+	 */
+	rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT);
+	if (rc < 0)
+		goto fail_on;
+	out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
+		       (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
+		       (0 << P0_EN_1V0X_LBN));
+	if (rc != out) {
+		netif_info(efx, hw, efx->net_dev, "power-cycling PHY\n");
+		rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+		if (rc)
+			goto fail_on;
+		schedule_timeout_uninterruptible(HZ);
+	}
+
+	for (i = 0; i < 20; ++i) {
+		/* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
+		out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
+			       (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
+			       (1 << P0_X_TRST_LBN));
+		if (efx->phy_mode & PHY_MODE_SPECIAL)
+			out |= 1 << P0_EN_3V3X_LBN;
+
+		rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+		if (rc)
+			goto fail_on;
+		msleep(10);
+
+		/* Turn on 1V power rail */
+		out &= ~(1 << P0_EN_1V0X_LBN);
+		rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+		if (rc)
+			goto fail_on;
+
+		netif_info(efx, hw, efx->net_dev,
+			   "waiting for DSP boot (attempt %d)...\n", i);
+
+		/* In flash config mode, DSP does not turn on AFE, so
+		 * just wait 1 second.
+		 */
+		if (efx->phy_mode & PHY_MODE_SPECIAL) {
+			schedule_timeout_uninterruptible(HZ);
+			return 0;
+		}
+
+		for (j = 0; j < 10; ++j) {
+			msleep(100);
+
+			/* Check DSP has asserted AFE power line */
+			rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
+			if (rc < 0)
+				goto fail_on;
+			if (rc & (1 << P1_AFE_PWD_LBN))
+				return 0;
+		}
+	}
+
+	netif_info(efx, hw, efx->net_dev, "timed out waiting for DSP boot\n");
+	rc = -ETIMEDOUT;
+fail_on:
+	sfe4001_poweroff(efx);
+	return rc;
+}
+
+static ssize_t show_phy_flash_cfg(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
+	return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL));
+}
+
+static ssize_t set_phy_flash_cfg(struct device *dev,
+				 struct device_attribute *attr,
+				 const char *buf, size_t count)
+{
+	struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
+	enum efx_phy_mode old_mode, new_mode;
+	int err;
+
+	rtnl_lock();
+	old_mode = efx->phy_mode;
+	if (count == 0 || *buf == '0')
+		new_mode = old_mode & ~PHY_MODE_SPECIAL;
+	else
+		new_mode = PHY_MODE_SPECIAL;
+	if (!((old_mode ^ new_mode) & PHY_MODE_SPECIAL)) {
+		err = 0;
+	} else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) {
+		err = -EBUSY;
+	} else {
+		/* Reset the PHY, reconfigure the MAC and enable/disable
+		 * MAC stats accordingly. */
+		efx->phy_mode = new_mode;
+		if (new_mode & PHY_MODE_SPECIAL)
+			falcon_stop_nic_stats(efx);
+		err = sfe4001_poweron(efx);
+		if (!err)
+			err = efx_reconfigure_port(efx);
+		if (!(new_mode & PHY_MODE_SPECIAL))
+			falcon_start_nic_stats(efx);
+	}
+	rtnl_unlock();
+
+	return err ? err : count;
+}
+
+static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg);
+
+static void sfe4001_fini(struct efx_nic *efx)
+{
+	struct falcon_board *board = falcon_board(efx);
+
+	netif_info(efx, drv, efx->net_dev, "%s\n", __func__);
+
+	device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+	sfe4001_poweroff(efx);
+	i2c_unregister_device(board->ioexp_client);
+	i2c_unregister_device(board->hwmon_client);
+}
+
+static int sfe4001_check_hw(struct efx_nic *efx)
+{
+	struct falcon_nic_data *nic_data = efx->nic_data;
+	s32 status;
+
+	/* If XAUI link is up then do not monitor */
+	if (EFX_WORKAROUND_7884(efx) && !nic_data->xmac_poll_required)
+		return 0;
+
+	/* Check the powered status of the PHY. Lack of power implies that
+	 * the MAX6647 has shut down power to it, probably due to a temp.
+	 * alarm. Reading the power status rather than the MAX6647 status
+	 * directly because the later is read-to-clear and would thus
+	 * start to power up the PHY again when polled, causing us to blip
+	 * the power undesirably.
+	 * We know we can read from the IO expander because we did
+	 * it during power-on. Assume failure now is bad news. */
+	status = i2c_smbus_read_byte_data(falcon_board(efx)->ioexp_client, P1_IN);
+	if (status >= 0 &&
+	    (status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
+		return 0;
+
+	/* Use board power control, not PHY power control */
+	sfe4001_poweroff(efx);
+	efx->phy_mode = PHY_MODE_OFF;
+
+	return (status < 0) ? -EIO : -ERANGE;
+}
+
+static struct i2c_board_info sfe4001_hwmon_info = {
+	I2C_BOARD_INFO("max6647", 0x4e),
+};
+
+/* This board uses an I2C expander to provider power to the PHY, which needs to
+ * be turned on before the PHY can be used.
+ * Context: Process context, rtnl lock held
+ */
+static int sfe4001_init(struct efx_nic *efx)
+{
+	struct falcon_board *board = falcon_board(efx);
+	int rc;
+
+#if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE)
+	board->hwmon_client =
+		i2c_new_device(&board->i2c_adap, &sfe4001_hwmon_info);
+#else
+	board->hwmon_client =
+		i2c_new_dummy(&board->i2c_adap, sfe4001_hwmon_info.addr);
+#endif
+	if (!board->hwmon_client)
+		return -EIO;
+
+	/* Raise board/PHY high limit from 85 to 90 degrees Celsius */
+	rc = i2c_smbus_write_byte_data(board->hwmon_client,
+				       MAX664X_REG_WLHO, 90);
+	if (rc)
+		goto fail_hwmon;
+
+	board->ioexp_client = i2c_new_dummy(&board->i2c_adap, PCA9539);
+	if (!board->ioexp_client) {
+		rc = -EIO;
+		goto fail_hwmon;
+	}
+
+	if (efx->phy_mode & PHY_MODE_SPECIAL) {
+		/* PHY won't generate a 156.25 MHz clock and MAC stats fetch
+		 * will fail. */
+		falcon_stop_nic_stats(efx);
+	}
+	rc = sfe4001_poweron(efx);
+	if (rc)
+		goto fail_ioexp;
+
+	rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+	if (rc)
+		goto fail_on;
+
+	netif_info(efx, hw, efx->net_dev, "PHY is powered on\n");
+	return 0;
+
+fail_on:
+	sfe4001_poweroff(efx);
+fail_ioexp:
+	i2c_unregister_device(board->ioexp_client);
+fail_hwmon:
+	i2c_unregister_device(board->hwmon_client);
+	return rc;
+}
+
+/*****************************************************************************
+ * Support for the SFE4002
+ *
+ */
+static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfe4002_lm87_regs[] = {
+	LM87_IN_LIMITS(0, 0x7c, 0x99),		/* 2.5V:  1.8V +/- 10% */
+	LM87_IN_LIMITS(1, 0x4c, 0x5e),		/* Vccp1: 1.2V +/- 10% */
+	LM87_IN_LIMITS(2, 0xac, 0xd4),		/* 3.3V:  3.3V +/- 10% */
+	LM87_IN_LIMITS(3, 0xac, 0xd4),		/* 5V:    5.0V +/- 10% */
+	LM87_IN_LIMITS(4, 0xac, 0xe0),		/* 12V:   10.8-14V */
+	LM87_IN_LIMITS(5, 0x3f, 0x4f),		/* Vccp2: 1.0V +/- 10% */
+	LM87_AIN_LIMITS(0, 0x98, 0xbb),		/* AIN1:  1.66V +/- 10% */
+	LM87_AIN_LIMITS(1, 0x8a, 0xa9),		/* AIN2:  1.5V +/- 10% */
+	LM87_TEMP_INT_LIMITS(0, 80 + FALCON_BOARD_TEMP_BIAS),
+	LM87_TEMP_EXT1_LIMITS(0, FALCON_JUNC_TEMP_MAX),
+	0
+};
+
+static struct i2c_board_info sfe4002_hwmon_info = {
+	I2C_BOARD_INFO("lm87", 0x2e),
+	.platform_data	= &sfe4002_lm87_channel,
+};
+
+/****************************************************************************/
+/* LED allocations. Note that on rev A0 boards the schematic and the reality
+ * differ: red and green are swapped. Below is the fixed (A1) layout (there
+ * are only 3 A0 boards in existence, so no real reason to make this
+ * conditional).
+ */
+#define SFE4002_FAULT_LED (2)	/* Red */
+#define SFE4002_RX_LED    (0)	/* Green */
+#define SFE4002_TX_LED    (1)	/* Amber */
+
+static void sfe4002_init_phy(struct efx_nic *efx)
+{
+	/* Set the TX and RX LEDs to reflect status and activity, and the
+	 * fault LED off */
+	falcon_qt202x_set_led(efx, SFE4002_TX_LED,
+			      QUAKE_LED_TXLINK | QUAKE_LED_LINK_ACTSTAT);
+	falcon_qt202x_set_led(efx, SFE4002_RX_LED,
+			      QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
+	falcon_qt202x_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
+}
+
+static void sfe4002_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
+{
+	falcon_qt202x_set_led(
+		efx, SFE4002_FAULT_LED,
+		(mode == EFX_LED_ON) ? QUAKE_LED_ON : QUAKE_LED_OFF);
+}
+
+static int sfe4002_check_hw(struct efx_nic *efx)
+{
+	struct falcon_board *board = falcon_board(efx);
+
+	/* A0 board rev. 4002s report a temperature fault the whole time
+	 * (bad sensor) so we mask it out. */
+	unsigned alarm_mask =
+		(board->major == 0 && board->minor == 0) ?
+		~LM87_ALARM_TEMP_EXT1 : ~0;
+
+	return efx_check_lm87(efx, alarm_mask);
+}
+
+static int sfe4002_init(struct efx_nic *efx)
+{
+	return efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs);
+}
+
+/*****************************************************************************
+ * Support for the SFN4112F
+ *
+ */
+static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfn4112f_lm87_regs[] = {
+	LM87_IN_LIMITS(0, 0x7c, 0x99),		/* 2.5V:  1.8V +/- 10% */
+	LM87_IN_LIMITS(1, 0x4c, 0x5e),		/* Vccp1: 1.2V +/- 10% */
+	LM87_IN_LIMITS(2, 0xac, 0xd4),		/* 3.3V:  3.3V +/- 10% */
+	LM87_IN_LIMITS(4, 0xac, 0xe0),		/* 12V:   10.8-14V */
+	LM87_IN_LIMITS(5, 0x3f, 0x4f),		/* Vccp2: 1.0V +/- 10% */
+	LM87_AIN_LIMITS(1, 0x8a, 0xa9),		/* AIN2:  1.5V +/- 10% */
+	LM87_TEMP_INT_LIMITS(0, 60 + FALCON_BOARD_TEMP_BIAS),
+	LM87_TEMP_EXT1_LIMITS(0, FALCON_JUNC_TEMP_MAX),
+	0
+};
+
+static struct i2c_board_info sfn4112f_hwmon_info = {
+	I2C_BOARD_INFO("lm87", 0x2e),
+	.platform_data	= &sfn4112f_lm87_channel,
+};
+
+#define SFN4112F_ACT_LED	0
+#define SFN4112F_LINK_LED	1
+
+static void sfn4112f_init_phy(struct efx_nic *efx)
+{
+	falcon_qt202x_set_led(efx, SFN4112F_ACT_LED,
+			      QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
+	falcon_qt202x_set_led(efx, SFN4112F_LINK_LED,
+			      QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
+}
+
+static void sfn4112f_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
+{
+	int reg;
+
+	switch (mode) {
+	case EFX_LED_OFF:
+		reg = QUAKE_LED_OFF;
+		break;
+	case EFX_LED_ON:
+		reg = QUAKE_LED_ON;
+		break;
+	default:
+		reg = QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT;
+		break;
+	}
+
+	falcon_qt202x_set_led(efx, SFN4112F_LINK_LED, reg);
+}
+
+static int sfn4112f_check_hw(struct efx_nic *efx)
+{
+	/* Mask out unused sensors */
+	return efx_check_lm87(efx, ~0x48);
+}
+
+static int sfn4112f_init(struct efx_nic *efx)
+{
+	return efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
+}
+
+/*****************************************************************************
+ * Support for the SFE4003
+ *
+ */
+static u8 sfe4003_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfe4003_lm87_regs[] = {
+	LM87_IN_LIMITS(0, 0x67, 0x7f),		/* 2.5V:  1.5V +/- 10% */
+	LM87_IN_LIMITS(1, 0x4c, 0x5e),		/* Vccp1: 1.2V +/- 10% */
+	LM87_IN_LIMITS(2, 0xac, 0xd4),		/* 3.3V:  3.3V +/- 10% */
+	LM87_IN_LIMITS(4, 0xac, 0xe0),		/* 12V:   10.8-14V */
+	LM87_IN_LIMITS(5, 0x3f, 0x4f),		/* Vccp2: 1.0V +/- 10% */
+	LM87_TEMP_INT_LIMITS(0, 70 + FALCON_BOARD_TEMP_BIAS),
+	0
+};
+
+static struct i2c_board_info sfe4003_hwmon_info = {
+	I2C_BOARD_INFO("lm87", 0x2e),
+	.platform_data	= &sfe4003_lm87_channel,
+};
+
+/* Board-specific LED info. */
+#define SFE4003_RED_LED_GPIO	11
+#define SFE4003_LED_ON		1
+#define SFE4003_LED_OFF		0
+
+static void sfe4003_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
+{
+	struct falcon_board *board = falcon_board(efx);
+
+	/* The LEDs were not wired to GPIOs before A3 */
+	if (board->minor < 3 && board->major == 0)
+		return;
+
+	falcon_txc_set_gpio_val(
+		efx, SFE4003_RED_LED_GPIO,
+		(mode == EFX_LED_ON) ? SFE4003_LED_ON : SFE4003_LED_OFF);
+}
+
+static void sfe4003_init_phy(struct efx_nic *efx)
+{
+	struct falcon_board *board = falcon_board(efx);
+
+	/* The LEDs were not wired to GPIOs before A3 */
+	if (board->minor < 3 && board->major == 0)
+		return;
+
+	falcon_txc_set_gpio_dir(efx, SFE4003_RED_LED_GPIO, TXC_GPIO_DIR_OUTPUT);
+	falcon_txc_set_gpio_val(efx, SFE4003_RED_LED_GPIO, SFE4003_LED_OFF);
+}
+
+static int sfe4003_check_hw(struct efx_nic *efx)
+{
+	struct falcon_board *board = falcon_board(efx);
+
+	/* A0/A1/A2 board rev. 4003s  report a temperature fault the whole time
+	 * (bad sensor) so we mask it out. */
+	unsigned alarm_mask =
+		(board->major == 0 && board->minor <= 2) ?
+		~LM87_ALARM_TEMP_EXT1 : ~0;
+
+	return efx_check_lm87(efx, alarm_mask);
+}
+
+static int sfe4003_init(struct efx_nic *efx)
+{
+	return efx_init_lm87(efx, &sfe4003_hwmon_info, sfe4003_lm87_regs);
+}
+
+static const struct falcon_board_type board_types[] = {
+	{
+		.id		= FALCON_BOARD_SFE4001,
+		.ref_model	= "SFE4001",
+		.gen_type	= "10GBASE-T adapter",
+		.init		= sfe4001_init,
+		.init_phy	= efx_port_dummy_op_void,
+		.fini		= sfe4001_fini,
+		.set_id_led	= tenxpress_set_id_led,
+		.monitor	= sfe4001_check_hw,
+	},
+	{
+		.id		= FALCON_BOARD_SFE4002,
+		.ref_model	= "SFE4002",
+		.gen_type	= "XFP adapter",
+		.init		= sfe4002_init,
+		.init_phy	= sfe4002_init_phy,
+		.fini		= efx_fini_lm87,
+		.set_id_led	= sfe4002_set_id_led,
+		.monitor	= sfe4002_check_hw,
+	},
+	{
+		.id		= FALCON_BOARD_SFE4003,
+		.ref_model	= "SFE4003",
+		.gen_type	= "10GBASE-CX4 adapter",
+		.init		= sfe4003_init,
+		.init_phy	= sfe4003_init_phy,
+		.fini		= efx_fini_lm87,
+		.set_id_led	= sfe4003_set_id_led,
+		.monitor	= sfe4003_check_hw,
+	},
+	{
+		.id		= FALCON_BOARD_SFN4112F,
+		.ref_model	= "SFN4112F",
+		.gen_type	= "SFP+ adapter",
+		.init		= sfn4112f_init,
+		.init_phy	= sfn4112f_init_phy,
+		.fini		= efx_fini_lm87,
+		.set_id_led	= sfn4112f_set_id_led,
+		.monitor	= sfn4112f_check_hw,
+	},
+};
+
+int falcon_probe_board(struct efx_nic *efx, u16 revision_info)
+{
+	struct falcon_board *board = falcon_board(efx);
+	u8 type_id = FALCON_BOARD_TYPE(revision_info);
+	int i;
+
+	board->major = FALCON_BOARD_MAJOR(revision_info);
+	board->minor = FALCON_BOARD_MINOR(revision_info);
+
+	for (i = 0; i < ARRAY_SIZE(board_types); i++)
+		if (board_types[i].id == type_id)
+			board->type = &board_types[i];
+
+	if (board->type) {
+		netif_info(efx, probe, efx->net_dev, "board is %s rev %c%d\n",
+			 (efx->pci_dev->subsystem_vendor ==
+			  PCI_VENDOR_ID_SOLARFLARE)
+			 ? board->type->ref_model : board->type->gen_type,
+			 'A' + board->major, board->minor);
+		return 0;
+	} else {
+		netif_err(efx, probe, efx->net_dev, "unknown board type %d\n",
+			  type_id);
+		return -ENODEV;
+	}
+}