i40e/i40evf: Split container ITR into current_itr and target_itr

This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.

The first value current_itr represents the current value of the register.

The second value target_itr represents the desired value of the register.

The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 39 insertions, 29 deletions

diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index c5f8e941f53e..1f130e931077 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -409,17 +409,16 @@ void i40evf_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector)
 static bool i40e_set_new_dynamic_itr(struct i40e_ring_container *rc)
 {
 	enum i40e_latency_range new_latency_range = rc->latency_range;
-	u32 new_itr = rc->itr;
 	int bytes_per_usec;
 	unsigned int usecs, estimated_usecs;
 
 	if (!rc->ring || !ITR_IS_DYNAMIC(rc->ring->itr_setting))
 		return false;
 
-	if (rc->total_packets == 0 || !rc->itr)
+	if (!rc->total_packets || !rc->current_itr)
 		return false;
 
-	usecs = (rc->itr << 1) * ITR_COUNTDOWN_START;
+	usecs = (rc->current_itr << 1) * ITR_COUNTDOWN_START;
 	bytes_per_usec = rc->total_bytes / usecs;
 
 	/* The calculations in this algorithm depend on interrupts actually
@@ -467,13 +466,13 @@ reset_latency:
 
 	switch (new_latency_range) {
 	case I40E_LOWEST_LATENCY:
-		new_itr = I40E_ITR_50K;
+		rc->target_itr = I40E_ITR_50K;
 		break;
 	case I40E_LOW_LATENCY:
-		new_itr = I40E_ITR_20K;
+		rc->target_itr = I40E_ITR_20K;
 		break;
 	case I40E_BULK_LATENCY:
-		new_itr = I40E_ITR_18K;
+		rc->target_itr = I40E_ITR_18K;
 		break;
 	default:
 		break;
@@ -483,11 +482,7 @@ reset_latency:
 	rc->total_packets = 0;
 	rc->last_itr_update = jiffies;
 
-	if (new_itr != rc->itr) {
-		rc->itr = new_itr;
-		return true;
-	}
-	return false;
+	return rc->target_itr != rc->current_itr;
 }
 
 /**
@@ -1502,9 +1497,7 @@ static inline void i40e_update_enable_itr(struct i40e_vsi *vsi,
 {
 	struct i40e_hw *hw = &vsi->back->hw;
 	bool rx = false, tx = false;
-	u32 txval;
-
-	txval = i40e_buildreg_itr(I40E_ITR_NONE, 0);
+	u32 intval;
 
 	/* avoid dynamic calculation if in countdown mode */
 	if (q_vector->itr_countdown > 0)
@@ -1519,26 +1512,43 @@ static inline void i40e_update_enable_itr(struct i40e_vsi *vsi,
 		 * use the same value for both ITR registers
 		 * when in adaptive mode (Rx and/or Tx)
 		 */
-		u16 itr = max(q_vector->tx.itr, q_vector->rx.itr);
-		u32 rxval;
-
-		q_vector->tx.itr = q_vector->rx.itr = itr;
-
-		/* set the INTENA_MSK_MASK so that this first write
-		 * won't actually enable the interrupt, instead just
-		 * updating the ITR (it's bit 31 PF and VF)
-		 */
-		rxval = i40e_buildreg_itr(I40E_RX_ITR, itr) | BIT(31);
+		u16 itr = max(q_vector->tx.target_itr,
+			      q_vector->rx.target_itr);
 
-		/* don't check _DOWN because interrupt isn't being enabled */
-		wr32(hw, INTREG(q_vector->reg_idx), rxval);
-
-		txval = i40e_buildreg_itr(I40E_TX_ITR, itr);
+		q_vector->tx.target_itr = itr;
+		q_vector->rx.target_itr = itr;
 	}
 
 enable_int:
+	if (q_vector->rx.target_itr != q_vector->rx.current_itr) {
+		intval = i40e_buildreg_itr(I40E_RX_ITR,
+					   q_vector->rx.target_itr);
+		q_vector->rx.current_itr = q_vector->rx.target_itr;
+
+		if (q_vector->tx.target_itr != q_vector->tx.current_itr) {
+			/* set the INTENA_MSK_MASK so that this first write
+			 * won't actually enable the interrupt, instead just
+			 * updating the ITR (it's bit 31 PF and VF)
+			 *
+			 * don't check _DOWN because interrupt isn't being
+			 * enabled
+			 */
+			wr32(hw, INTREG(q_vector->reg_idx),
+			     intval | BIT(31));
+			/* now that Rx is done process Tx update */
+			goto update_tx;
+		}
+	} else if (q_vector->tx.target_itr != q_vector->tx.current_itr) {
+update_tx:
+		intval = i40e_buildreg_itr(I40E_TX_ITR,
+					   q_vector->tx.target_itr);
+		q_vector->tx.current_itr = q_vector->tx.target_itr;
+	} else {
+		intval = i40e_buildreg_itr(I40E_ITR_NONE, 0);
+	}
+
 	if (!test_bit(__I40E_VSI_DOWN, vsi->state))
-		wr32(hw, INTREG(q_vector->reg_idx), txval);
+		wr32(hw, INTREG(q_vector->reg_idx), intval);
 
 	if (q_vector->itr_countdown)
 		q_vector->itr_countdown--;