Merge drm/drm-next into drm-intel-next

Sync up with drm-next to get v5.16-rc2.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

5 files changed, 216 insertions, 98 deletions

diff --git a/drivers/net/dsa/sja1105/sja1105.h b/drivers/net/dsa/sja1105/sja1105.h
index 5e5d24e7c02b..21dba16af097 100644
--- a/drivers/net/dsa/sja1105/sja1105.h
+++ b/drivers/net/dsa/sja1105/sja1105.h
@@ -20,6 +20,27 @@
 #define SJA1105_AGEING_TIME_MS(ms)	((ms) / 10)
 #define SJA1105_NUM_L2_POLICERS		SJA1110_MAX_L2_POLICING_COUNT
 
+/* Calculated assuming 1Gbps, where the clock has 125 MHz (8 ns period)
+ * To avoid floating point operations, we'll multiply the degrees by 10
+ * to get a "phase" and get 1 decimal point precision.
+ */
+#define SJA1105_RGMII_DELAY_PS_TO_PHASE(ps) \
+	(((ps) * 360) / 800)
+#define SJA1105_RGMII_DELAY_PHASE_TO_PS(phase) \
+	((800 * (phase)) / 360)
+#define SJA1105_RGMII_DELAY_PHASE_TO_HW(phase) \
+	(((phase) - 738) / 9)
+#define SJA1105_RGMII_DELAY_PS_TO_HW(ps) \
+	SJA1105_RGMII_DELAY_PHASE_TO_HW(SJA1105_RGMII_DELAY_PS_TO_PHASE(ps))
+
+/* Valid range in degrees is a value between 73.8 and 101.7
+ * in 0.9 degree increments
+ */
+#define SJA1105_RGMII_DELAY_MIN_PS \
+	SJA1105_RGMII_DELAY_PHASE_TO_PS(738)
+#define SJA1105_RGMII_DELAY_MAX_PS \
+	SJA1105_RGMII_DELAY_PHASE_TO_PS(1017)
+
 typedef enum {
 	SPI_READ = 0,
 	SPI_WRITE = 1,
@@ -222,16 +243,14 @@ struct sja1105_flow_block {
 
 struct sja1105_private {
 	struct sja1105_static_config static_config;
-	bool rgmii_rx_delay[SJA1105_MAX_NUM_PORTS];
-	bool rgmii_tx_delay[SJA1105_MAX_NUM_PORTS];
+	int rgmii_rx_delay_ps[SJA1105_MAX_NUM_PORTS];
+	int rgmii_tx_delay_ps[SJA1105_MAX_NUM_PORTS];
 	phy_interface_t phy_mode[SJA1105_MAX_NUM_PORTS];
 	bool fixed_link[SJA1105_MAX_NUM_PORTS];
-	bool vlan_aware;
 	unsigned long ucast_egress_floods;
 	unsigned long bcast_egress_floods;
 	const struct sja1105_info *info;
 	size_t max_xfer_len;
-	struct gpio_desc *reset_gpio;
 	struct spi_device *spidev;
 	struct dsa_switch *ds;
 	u16 bridge_pvid[SJA1105_MAX_NUM_PORTS];
@@ -242,6 +261,8 @@ struct sja1105_private {
 	 * the switch doesn't confuse them with one another.
 	 */
 	struct mutex mgmt_lock;
+	/* Serializes access to the dynamic config interface */
+	struct mutex dynamic_config_lock;
 	struct devlink_region **regions;
 	struct sja1105_cbs_entry *cbs;
 	struct mii_bus *mdio_base_t1;
diff --git a/drivers/net/dsa/sja1105/sja1105_clocking.c b/drivers/net/dsa/sja1105/sja1105_clocking.c
index 5bbf1707f2af..e3699f76f6d7 100644
--- a/drivers/net/dsa/sja1105/sja1105_clocking.c
+++ b/drivers/net/dsa/sja1105/sja1105_clocking.c
@@ -498,17 +498,6 @@ sja1110_cfg_pad_mii_id_packing(void *buf, struct sja1105_cfg_pad_mii_id *cmd,
 	sja1105_packing(buf, &cmd->txc_pd,          0,  0, size, op);
 }
 
-/* Valid range in degrees is an integer between 73.8 and 101.7 */
-static u64 sja1105_rgmii_delay(u64 phase)
-{
-	/* UM11040.pdf: The delay in degree phase is 73.8 + delay_tune * 0.9.
-	 * To avoid floating point operations we'll multiply by 10
-	 * and get 1 decimal point precision.
-	 */
-	phase *= 10;
-	return (phase - 738) / 9;
-}
-
 /* The RGMII delay setup procedure is 2-step and gets called upon each
  * .phylink_mac_config. Both are strategic.
  * The reason is that the RX Tunable Delay Line of the SJA1105 MAC has issues
@@ -521,13 +510,15 @@ int sja1105pqrs_setup_rgmii_delay(const void *ctx, int port)
 	const struct sja1105_private *priv = ctx;
 	const struct sja1105_regs *regs = priv->info->regs;
 	struct sja1105_cfg_pad_mii_id pad_mii_id = {0};
+	int rx_delay = priv->rgmii_rx_delay_ps[port];
+	int tx_delay = priv->rgmii_tx_delay_ps[port];
 	u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
 	int rc;
 
-	if (priv->rgmii_rx_delay[port])
-		pad_mii_id.rxc_delay = sja1105_rgmii_delay(90);
-	if (priv->rgmii_tx_delay[port])
-		pad_mii_id.txc_delay = sja1105_rgmii_delay(90);
+	if (rx_delay)
+		pad_mii_id.rxc_delay = SJA1105_RGMII_DELAY_PS_TO_HW(rx_delay);
+	if (tx_delay)
+		pad_mii_id.txc_delay = SJA1105_RGMII_DELAY_PS_TO_HW(tx_delay);
 
 	/* Stage 1: Turn the RGMII delay lines off. */
 	pad_mii_id.rxc_bypass = 1;
@@ -542,11 +533,11 @@ int sja1105pqrs_setup_rgmii_delay(const void *ctx, int port)
 		return rc;
 
 	/* Stage 2: Turn the RGMII delay lines on. */
-	if (priv->rgmii_rx_delay[port]) {
+	if (rx_delay) {
 		pad_mii_id.rxc_bypass = 0;
 		pad_mii_id.rxc_pd = 0;
 	}
-	if (priv->rgmii_tx_delay[port]) {
+	if (tx_delay) {
 		pad_mii_id.txc_bypass = 0;
 		pad_mii_id.txc_pd = 0;
 	}
@@ -561,20 +552,22 @@ int sja1110_setup_rgmii_delay(const void *ctx, int port)
 	const struct sja1105_private *priv = ctx;
 	const struct sja1105_regs *regs = priv->info->regs;
 	struct sja1105_cfg_pad_mii_id pad_mii_id = {0};
+	int rx_delay = priv->rgmii_rx_delay_ps[port];
+	int tx_delay = priv->rgmii_tx_delay_ps[port];
 	u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
 
 	pad_mii_id.rxc_pd = 1;
 	pad_mii_id.txc_pd = 1;
 
-	if (priv->rgmii_rx_delay[port]) {
-		pad_mii_id.rxc_delay = sja1105_rgmii_delay(90);
+	if (rx_delay) {
+		pad_mii_id.rxc_delay = SJA1105_RGMII_DELAY_PS_TO_HW(rx_delay);
 		/* The "BYPASS" bit in SJA1110 is actually a "don't bypass" */
 		pad_mii_id.rxc_bypass = 1;
 		pad_mii_id.rxc_pd = 0;
 	}
 
-	if (priv->rgmii_tx_delay[port]) {
-		pad_mii_id.txc_delay = sja1105_rgmii_delay(90);
+	if (tx_delay) {
+		pad_mii_id.txc_delay = SJA1105_RGMII_DELAY_PS_TO_HW(tx_delay);
 		pad_mii_id.txc_bypass = 1;
 		pad_mii_id.txc_pd = 0;
 	}
diff --git a/drivers/net/dsa/sja1105/sja1105_dynamic_config.c b/drivers/net/dsa/sja1105/sja1105_dynamic_config.c
index f2049f52833c..7729d3f8b7f5 100644
--- a/drivers/net/dsa/sja1105/sja1105_dynamic_config.c
+++ b/drivers/net/dsa/sja1105/sja1105_dynamic_config.c
@@ -1170,6 +1170,56 @@ const struct sja1105_dynamic_table_ops sja1110_dyn_ops[BLK_IDX_MAX_DYN] = {
 	},
 };
 
+#define SJA1105_DYNAMIC_CONFIG_SLEEP_US		10
+#define SJA1105_DYNAMIC_CONFIG_TIMEOUT_US	100000
+
+static int
+sja1105_dynamic_config_poll_valid(struct sja1105_private *priv,
+				  struct sja1105_dyn_cmd *cmd,
+				  const struct sja1105_dynamic_table_ops *ops)
+{
+	u8 packed_buf[SJA1105_MAX_DYN_CMD_SIZE] = {};
+	int rc;
+
+	/* We don't _need_ to read the full entry, just the command area which
+	 * is a fixed SJA1105_SIZE_DYN_CMD. But our cmd_packing() API expects a
+	 * buffer that contains the full entry too. Additionally, our API
+	 * doesn't really know how many bytes into the buffer does the command
+	 * area really begin. So just read back the whole entry.
+	 */
+	rc = sja1105_xfer_buf(priv, SPI_READ, ops->addr, packed_buf,
+			      ops->packed_size);
+	if (rc)
+		return rc;
+
+	/* Unpack the command structure, and return it to the caller in case it
+	 * needs to perform further checks on it (VALIDENT).
+	 */
+	memset(cmd, 0, sizeof(*cmd));
+	ops->cmd_packing(packed_buf, cmd, UNPACK);
+
+	/* Hardware hasn't cleared VALID => still working on it */
+	return cmd->valid ? -EAGAIN : 0;
+}
+
+/* Poll the dynamic config entry's control area until the hardware has
+ * cleared the VALID bit, which means we have confirmation that it has
+ * finished processing the command.
+ */
+static int
+sja1105_dynamic_config_wait_complete(struct sja1105_private *priv,
+				     struct sja1105_dyn_cmd *cmd,
+				     const struct sja1105_dynamic_table_ops *ops)
+{
+	int rc;
+
+	return read_poll_timeout(sja1105_dynamic_config_poll_valid,
+				 rc, rc != -EAGAIN,
+				 SJA1105_DYNAMIC_CONFIG_SLEEP_US,
+				 SJA1105_DYNAMIC_CONFIG_TIMEOUT_US,
+				 false, priv, cmd, ops);
+}
+
 /* Provides read access to the settings through the dynamic interface
  * of the switch.
  * @blk_idx	is used as key to select from the sja1105_dynamic_table_ops.
@@ -1196,7 +1246,6 @@ int sja1105_dynamic_config_read(struct sja1105_private *priv,
 	struct sja1105_dyn_cmd cmd = {0};
 	/* SPI payload buffer */
 	u8 packed_buf[SJA1105_MAX_DYN_CMD_SIZE] = {0};
-	int retries = 3;
 	int rc;
 
 	if (blk_idx >= BLK_IDX_MAX_DYN)
@@ -1234,33 +1283,21 @@ int sja1105_dynamic_config_read(struct sja1105_private *priv,
 		ops->entry_packing(packed_buf, entry, PACK);
 
 	/* Send SPI write operation: read config table entry */
+	mutex_lock(&priv->dynamic_config_lock);
 	rc = sja1105_xfer_buf(priv, SPI_WRITE, ops->addr, packed_buf,
 			      ops->packed_size);
-	if (rc < 0)
+	if (rc < 0) {
+		mutex_unlock(&priv->dynamic_config_lock);
 		return rc;
+	}
 
-	/* Loop until we have confirmation that hardware has finished
-	 * processing the command and has cleared the VALID field
-	 */
-	do {
-		memset(packed_buf, 0, ops->packed_size);
-
-		/* Retrieve the read operation's result */
-		rc = sja1105_xfer_buf(priv, SPI_READ, ops->addr, packed_buf,
-				      ops->packed_size);
-		if (rc < 0)
-			return rc;
-
-		cmd = (struct sja1105_dyn_cmd) {0};
-		ops->cmd_packing(packed_buf, &cmd, UNPACK);
-
-		if (!cmd.valident && !(ops->access & OP_VALID_ANYWAY))
-			return -ENOENT;
-		cpu_relax();
-	} while (cmd.valid && --retries);
+	rc = sja1105_dynamic_config_wait_complete(priv, &cmd, ops);
+	mutex_unlock(&priv->dynamic_config_lock);
+	if (rc < 0)
+		return rc;
 
-	if (cmd.valid)
-		return -ETIMEDOUT;
+	if (!cmd.valident && !(ops->access & OP_VALID_ANYWAY))
+		return -ENOENT;
 
 	/* Don't dereference possibly NULL pointer - maybe caller
 	 * only wanted to see whether the entry existed or not.
@@ -1316,8 +1353,16 @@ int sja1105_dynamic_config_write(struct sja1105_private *priv,
 		ops->entry_packing(packed_buf, entry, PACK);
 
 	/* Send SPI write operation: read config table entry */
+	mutex_lock(&priv->dynamic_config_lock);
 	rc = sja1105_xfer_buf(priv, SPI_WRITE, ops->addr, packed_buf,
 			      ops->packed_size);
+	if (rc < 0) {
+		mutex_unlock(&priv->dynamic_config_lock);
+		return rc;
+	}
+
+	rc = sja1105_dynamic_config_wait_complete(priv, &cmd, ops);
+	mutex_unlock(&priv->dynamic_config_lock);
 	if (rc < 0)
 		return rc;
 
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 924c3f129992..c343effe2e96 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -27,15 +27,29 @@
 
 #define SJA1105_UNKNOWN_MULTICAST	0x010000000000ull
 
-static void sja1105_hw_reset(struct gpio_desc *gpio, unsigned int pulse_len,
-			     unsigned int startup_delay)
+/* Configure the optional reset pin and bring up switch */
+static int sja1105_hw_reset(struct device *dev, unsigned int pulse_len,
+			    unsigned int startup_delay)
 {
+	struct gpio_desc *gpio;
+
+	gpio = gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(gpio))
+		return PTR_ERR(gpio);
+
+	if (!gpio)
+		return 0;
+
 	gpiod_set_value_cansleep(gpio, 1);
 	/* Wait for minimum reset pulse length */
 	msleep(pulse_len);
 	gpiod_set_value_cansleep(gpio, 0);
 	/* Wait until chip is ready after reset */
 	msleep(startup_delay);
+
+	gpiod_put(gpio);
+
+	return 0;
 }
 
 static void
@@ -1095,27 +1109,78 @@ static int sja1105_static_config_load(struct sja1105_private *priv)
 	return sja1105_static_config_upload(priv);
 }
 
-static int sja1105_parse_rgmii_delays(struct sja1105_private *priv)
+/* This is the "new way" for a MAC driver to configure its RGMII delay lines,
+ * based on the explicit "rx-internal-delay-ps" and "tx-internal-delay-ps"
+ * properties. It has the advantage of working with fixed links and with PHYs
+ * that apply RGMII delays too, and the MAC driver needs not perform any
+ * special checks.
+ *
+ * Previously we were acting upon the "phy-mode" property when we were
+ * operating in fixed-link, basically acting as a PHY, but with a reversed
+ * interpretation: PHY_INTERFACE_MODE_RGMII_TXID means that the MAC should
+ * behave as if it is connected to a PHY which has applied RGMII delays in the
+ * TX direction. So if anything, RX delays should have been added by the MAC,
+ * but we were adding TX delays.
+ *
+ * If the "{rx,tx}-internal-delay-ps" properties are not specified, we fall
+ * back to the legacy behavior and apply delays on fixed-link ports based on
+ * the reverse interpretation of the phy-mode. This is a deviation from the
+ * expected default behavior which is to simply apply no delays. To achieve
+ * that behavior with the new bindings, it is mandatory to specify
+ * "{rx,tx}-internal-delay-ps" with a value of 0.
+ */
+static int sja1105_parse_rgmii_delays(struct sja1105_private *priv, int port,
+				      struct device_node *port_dn)
 {
-	struct dsa_switch *ds = priv->ds;
-	int port;
+	phy_interface_t phy_mode = priv->phy_mode[port];
+	struct device *dev = &priv->spidev->dev;
+	int rx_delay = -1, tx_delay = -1;
 
-	for (port = 0; port < ds->num_ports; port++) {
-		if (!priv->fixed_link[port])
-			continue;
+	if (!phy_interface_mode_is_rgmii(phy_mode))
+		return 0;
 
-		if (priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_RXID ||
-		    priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_ID)
-			priv->rgmii_rx_delay[port] = true;
+	of_property_read_u32(port_dn, "rx-internal-delay-ps", &rx_delay);
+	of_property_read_u32(port_dn, "tx-internal-delay-ps", &tx_delay);
 
-		if (priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_TXID ||
-		    priv->phy_mode[port] == PHY_INTERFACE_MODE_RGMII_ID)
-			priv->rgmii_tx_delay[port] = true;
+	if (rx_delay == -1 && tx_delay == -1 && priv->fixed_link[port]) {
+		dev_warn(dev,
+			 "Port %d interpreting RGMII delay settings based on \"phy-mode\" property, "
+			 "please update device tree to specify \"rx-internal-delay-ps\" and "
+			 "\"tx-internal-delay-ps\"",
+			 port);
 
-		if ((priv->rgmii_rx_delay[port] || priv->rgmii_tx_delay[port]) &&
-		    !priv->info->setup_rgmii_delay)
-			return -EINVAL;
+		if (phy_mode == PHY_INTERFACE_MODE_RGMII_RXID ||
+		    phy_mode == PHY_INTERFACE_MODE_RGMII_ID)
+			rx_delay = 2000;
+
+		if (phy_mode == PHY_INTERFACE_MODE_RGMII_TXID ||
+		    phy_mode == PHY_INTERFACE_MODE_RGMII_ID)
+			tx_delay = 2000;
+	}
+
+	if (rx_delay < 0)
+		rx_delay = 0;
+	if (tx_delay < 0)
+		tx_delay = 0;
+
+	if ((rx_delay || tx_delay) && !priv->info->setup_rgmii_delay) {
+		dev_err(dev, "Chip cannot apply RGMII delays\n");
+		return -EINVAL;
 	}
+
+	if ((rx_delay && rx_delay < SJA1105_RGMII_DELAY_MIN_PS) ||
+	    (tx_delay && tx_delay < SJA1105_RGMII_DELAY_MIN_PS) ||
+	    (rx_delay > SJA1105_RGMII_DELAY_MAX_PS) ||
+	    (tx_delay > SJA1105_RGMII_DELAY_MAX_PS)) {
+		dev_err(dev,
+			"port %d RGMII delay values out of range, must be between %d and %d ps\n",
+			port, SJA1105_RGMII_DELAY_MIN_PS, SJA1105_RGMII_DELAY_MAX_PS);
+		return -ERANGE;
+	}
+
+	priv->rgmii_rx_delay_ps[port] = rx_delay;
+	priv->rgmii_tx_delay_ps[port] = tx_delay;
+
 	return 0;
 }
 
@@ -1166,6 +1231,12 @@ static int sja1105_parse_ports_node(struct sja1105_private *priv,
 		}
 
 		priv->phy_mode[index] = phy_mode;
+
+		err = sja1105_parse_rgmii_delays(priv, index, child);
+		if (err) {
+			of_node_put(child);
+			return err;
+		}
 	}
 
 	return 0;
@@ -1360,7 +1431,7 @@ static void sja1105_phylink_validate(struct dsa_switch *ds, int port,
 	 */
 	if (state->interface != PHY_INTERFACE_MODE_NA &&
 	    sja1105_phy_mode_mismatch(priv, port, state->interface)) {
-		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+		linkmode_zero(supported);
 		return;
 	}
 
@@ -1380,9 +1451,8 @@ static void sja1105_phylink_validate(struct dsa_switch *ds, int port,
 		phylink_set(mask, 2500baseX_Full);
 	}
 
-	bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS);
-	bitmap_and(state->advertising, state->advertising, mask,
-		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	linkmode_and(supported, supported, mask);
+	linkmode_and(state->advertising, state->advertising, mask);
 }
 
 static int
@@ -1766,6 +1836,7 @@ static int sja1105_fdb_del(struct dsa_switch *ds, int port,
 static int sja1105_fdb_dump(struct dsa_switch *ds, int port,
 			    dsa_fdb_dump_cb_t *cb, void *data)
 {
+	struct dsa_port *dp = dsa_to_port(ds, port);
 	struct sja1105_private *priv = ds->priv;
 	struct device *dev = ds->dev;
 	int i;
@@ -1802,7 +1873,7 @@ static int sja1105_fdb_dump(struct dsa_switch *ds, int port,
 		u64_to_ether_addr(l2_lookup.macaddr, macaddr);
 
 		/* We need to hide the dsa_8021q VLANs from the user. */
-		if (!priv->vlan_aware)
+		if (!dsa_port_is_vlan_filtering(dp))
 			l2_lookup.vlanid = 0;
 		rc = cb(macaddr, l2_lookup.vlanid, l2_lookup.lockeds, data);
 		if (rc)
@@ -2295,11 +2366,6 @@ int sja1105_vlan_filtering(struct dsa_switch *ds, int port, bool enabled,
 		tpid2 = ETH_P_SJA1105;
 	}
 
-	if (priv->vlan_aware == enabled)
-		return 0;
-
-	priv->vlan_aware = enabled;
-
 	table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS];
 	general_params = table->entries;
 	/* EtherType used to identify inner tagged (C-tag) VLAN traffic */
@@ -2332,7 +2398,7 @@ int sja1105_vlan_filtering(struct dsa_switch *ds, int port, bool enabled,
 	 */
 	table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS];
 	l2_lookup_params = table->entries;
-	l2_lookup_params->shared_learn = !priv->vlan_aware;
+	l2_lookup_params->shared_learn = !enabled;
 
 	for (port = 0; port < ds->num_ports; port++) {
 		if (dsa_is_unused_port(ds, port))
@@ -2965,7 +3031,6 @@ static int sja1105_setup_ports(struct sja1105_private *priv)
 			continue;
 
 		dp->priv = sp;
-		sp->dp = dp;
 		sp->data = tagger_data;
 		slave = dp->slave;
 		kthread_init_work(&sp->xmit_work, sja1105_port_deferred_xmit);
@@ -3229,17 +3294,14 @@ static int sja1105_probe(struct spi_device *spi)
 		return -EINVAL;
 	}
 
+	rc = sja1105_hw_reset(dev, 1, 1);
+	if (rc)
+		return rc;
+
 	priv = devm_kzalloc(dev, sizeof(struct sja1105_private), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
 
-	/* Configure the optional reset pin and bring up switch */
-	priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
-	if (IS_ERR(priv->reset_gpio))
-		dev_dbg(dev, "reset-gpios not defined, ignoring\n");
-	else
-		sja1105_hw_reset(priv->reset_gpio, 1, 1);
-
 	/* Populate our driver private structure (priv) based on
 	 * the device tree node that was probed (spi)
 	 */
@@ -3303,6 +3365,7 @@ static int sja1105_probe(struct spi_device *spi)
 	priv->ds = ds;
 
 	mutex_init(&priv->ptp_data.lock);
+	mutex_init(&priv->dynamic_config_lock);
 	mutex_init(&priv->mgmt_lock);
 
 	rc = sja1105_parse_dt(priv);
@@ -3311,15 +3374,6 @@ static int sja1105_probe(struct spi_device *spi)
 		return rc;
 	}
 
-	/* Error out early if internal delays are required through DT
-	 * and we can't apply them.
-	 */
-	rc = sja1105_parse_rgmii_delays(priv);
-	if (rc < 0) {
-		dev_err(ds->dev, "RGMII delay not supported\n");
-		return rc;
-	}
-
 	if (IS_ENABLED(CONFIG_NET_SCH_CBS)) {
 		priv->cbs = devm_kcalloc(dev, priv->info->num_cbs_shapers,
 					 sizeof(struct sja1105_cbs_entry),
diff --git a/drivers/net/dsa/sja1105/sja1105_vl.c b/drivers/net/dsa/sja1105/sja1105_vl.c
index 6802f4057cc0..f5dca6a9b0f9 100644
--- a/drivers/net/dsa/sja1105/sja1105_vl.c
+++ b/drivers/net/dsa/sja1105/sja1105_vl.c
@@ -394,7 +394,8 @@ static int sja1105_init_virtual_links(struct sja1105_private *priv,
 				vl_lookup[k].vlanid = rule->key.vl.vid;
 				vl_lookup[k].vlanprior = rule->key.vl.pcp;
 			} else {
-				u16 vid = dsa_8021q_rx_vid(priv->ds, port);
+				struct dsa_port *dp = dsa_to_port(priv->ds, port);
+				u16 vid = dsa_tag_8021q_rx_vid(dp);
 
 				vl_lookup[k].vlanid = vid;
 				vl_lookup[k].vlanprior = 0;
@@ -494,13 +495,15 @@ int sja1105_vl_redirect(struct sja1105_private *priv, int port,
 			bool append)
 {
 	struct sja1105_rule *rule = sja1105_rule_find(priv, cookie);
+	struct dsa_port *dp = dsa_to_port(priv->ds, port);
+	bool vlan_aware = dsa_port_is_vlan_filtering(dp);
 	int rc;
 
-	if (!priv->vlan_aware && key->type != SJA1105_KEY_VLAN_UNAWARE_VL) {
+	if (!vlan_aware && key->type != SJA1105_KEY_VLAN_UNAWARE_VL) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "Can only redirect based on DMAC");
 		return -EOPNOTSUPP;
-	} else if (priv->vlan_aware && key->type != SJA1105_KEY_VLAN_AWARE_VL) {
+	} else if (vlan_aware && key->type != SJA1105_KEY_VLAN_AWARE_VL) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "Can only redirect based on {DMAC, VID, PCP}");
 		return -EOPNOTSUPP;
@@ -568,6 +571,8 @@ int sja1105_vl_gate(struct sja1105_private *priv, int port,
 		    u32 num_entries, struct action_gate_entry *entries)
 {
 	struct sja1105_rule *rule = sja1105_rule_find(priv, cookie);
+	struct dsa_port *dp = dsa_to_port(priv->ds, port);
+	bool vlan_aware = dsa_port_is_vlan_filtering(dp);
 	int ipv = -1;
 	int i, rc;
 	s32 rem;
@@ -592,11 +597,11 @@ int sja1105_vl_gate(struct sja1105_private *priv, int port,
 		return -ERANGE;
 	}
 
-	if (!priv->vlan_aware && key->type != SJA1105_KEY_VLAN_UNAWARE_VL) {
+	if (!vlan_aware && key->type != SJA1105_KEY_VLAN_UNAWARE_VL) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "Can only gate based on DMAC");
 		return -EOPNOTSUPP;
-	} else if (priv->vlan_aware && key->type != SJA1105_KEY_VLAN_AWARE_VL) {
+	} else if (vlan_aware && key->type != SJA1105_KEY_VLAN_AWARE_VL) {
 		NL_SET_ERR_MSG_MOD(extack,
 				   "Can only gate based on {DMAC, VID, PCP}");
 		return -EOPNOTSUPP;