bnx2x: Split PHY functions

Move the code into PHY oriented functions, and for that a new structure
is defines for each PHY which contain PHY properties and its own
functions. This also enables to encapsulate all PHY specific operations
into the PHY functions. During initialization, the PHYs will be probed
by the "bnx2x_phy_probe" function to detect which PHYs exist on-board,
and configure them accordingly. Note that the ext_phy_reset
implementation was incorporated in the ext_phy_init since it is actually
part of the PHY initialization procedure.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 91 insertions, 18 deletions

diff --git a/drivers/net/bnx2x/bnx2x_link.h b/drivers/net/bnx2x/bnx2x_link.h
index 9bfe7fa452bc..9717cb1fbad0 100644
--- a/drivers/net/bnx2x/bnx2x_link.h
+++ b/drivers/net/bnx2x/bnx2x_link.h
@@ -46,6 +46,15 @@
 #define SFP_EEPROM_PART_NO_ADDR 		0x28
 #define SFP_EEPROM_PART_NO_SIZE		16
 #define PWR_FLT_ERR_MSG_LEN			250
+
+#define XGXS_EXT_PHY_TYPE(ext_phy_config) \
+		((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
+#define XGXS_EXT_PHY_ADDR(ext_phy_config) \
+		(((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> \
+		 PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT)
+#define SERDES_EXT_PHY_TYPE(ext_phy_config) \
+		((ext_phy_config) & PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)
+
 /* Single Media Direct board is the plain 577xx board with CX4/RJ45 jacks */
 #define SINGLE_MEDIA_DIRECT(params)	(params->num_phys == 1)
 /* Single Media board contains single external phy */
@@ -58,6 +67,10 @@
 
 #define MAX_PHYS	2
 
+/* Same configuration is shared between the XGXS and the first external phy */
+#define LINK_CONFIG_SIZE (MAX_PHYS - 1)
+#define LINK_CONFIG_IDX(_phy_idx) ((_phy_idx == INT_PHY) ? \
+					 0 : (_phy_idx - 1))
 /***********************************************************/
 /*                      bnx2x_phy struct                     */
 /*  Defines the required arguments and function per phy    */
@@ -66,13 +79,88 @@ struct link_vars;
 struct link_params;
 struct bnx2x_phy;
 
+typedef u8 (*config_init_t)(struct bnx2x_phy *phy, struct link_params *params,
+			    struct link_vars *vars);
+typedef u8 (*read_status_t)(struct bnx2x_phy *phy, struct link_params *params,
+			    struct link_vars *vars);
+typedef void (*link_reset_t)(struct bnx2x_phy *phy,
+			     struct link_params *params);
+typedef void (*config_loopback_t)(struct bnx2x_phy *phy,
+				  struct link_params *params);
+typedef u8 (*format_fw_ver_t)(u32 raw, u8 *str, u16 *len);
+typedef void (*hw_reset_t)(struct bnx2x_phy *phy, struct link_params *params);
+typedef void (*set_link_led_t)(struct bnx2x_phy *phy,
+			       struct link_params *params, u8 mode);
+
 struct bnx2x_phy {
 	u32 type;
 
 	/* Loaded during init */
 	u8 addr;
 
+	u8 flags;
+	/* Require HW lock */
+#define FLAGS_HW_LOCK_REQUIRED		(1<<0)
+	/* No Over-Current detection */
+#define FLAGS_NOC			(1<<1)
+	/* Fan failure detection required */
+#define FLAGS_FAN_FAILURE_DET_REQ	(1<<2)
+	/* Initialize first the XGXS and only then the phy itself */
+#define FLAGS_INIT_XGXS_FIRST	(1<<3)
+
+	u8 def_md_devad;
+	u8 reserved;
+	/* preemphasis values for the rx side */
+	u16 rx_preemphasis[4];
+
+	/* preemphasis values for the tx side */
+	u16 tx_preemphasis[4];
+
+	/* EMAC address for access MDIO */
 	u32 mdio_ctrl;
+
+	u32 supported;
+
+	u32 media_type;
+#define	ETH_PHY_UNSPECIFIED 0x0
+#define	ETH_PHY_SFP_FIBER   0x1
+#define	ETH_PHY_XFP_FIBER   0x2
+#define	ETH_PHY_DA_TWINAX   0x3
+#define	ETH_PHY_BASE_T      0x4
+#define	ETH_PHY_NOT_PRESENT 0xff
+
+	/* The address in which version is located*/
+	u32 ver_addr;
+
+	u16 req_flow_ctrl;
+
+	u16 req_line_speed;
+
+	u32 speed_cap_mask;
+
+	u16 req_duplex;
+	u16 rsrv;
+	/* Called per phy/port init, and it configures LASI, speed, autoneg,
+	 duplex, flow control negotiation, etc. */
+	config_init_t config_init;
+
+	/* Called due to interrupt. It determines the link, speed */
+	read_status_t read_status;
+
+	/* Called when driver is unloading. Should reset the phy */
+	link_reset_t link_reset;
+
+	/* Set the loopback configuration for the phy */
+	config_loopback_t config_loopback;
+
+	/* Format the given raw number into str up to len */
+	format_fw_ver_t format_fw_ver;
+
+	/* Reset the phy (both ports) */
+	hw_reset_t hw_reset;
+
+	/* Set link led mode (on/off/oper)*/
+	set_link_led_t set_link_led;
 };
 
 /* Inputs parameters to the CLC */
@@ -106,38 +194,23 @@ struct link_params {
 #define SWITCH_CFG_10G		PORT_FEATURE_CON_SWITCH_10G_SWITCH
 #define SWITCH_CFG_AUTO_DETECT	PORT_FEATURE_CON_SWITCH_AUTO_DETECT
 
-	u16 hw_led_mode; /* part of the hw_config read from the shmem */
-
-	/* phy_addr populated by the phy_init function */
-	u8 phy_addr;
-	/*u8 reserved1;*/
-
 	u32 lane_config;
-	u32 ext_phy_config;
-#define XGXS_EXT_PHY_TYPE(ext_phy_config) \
-		((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
-#define XGXS_EXT_PHY_ADDR(ext_phy_config) \
-		(((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> \
-		 PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT)
-#define SERDES_EXT_PHY_TYPE(ext_phy_config) \
-		((ext_phy_config) & PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)
 
 	/* Phy register parameter */
 	u32 chip_id;
 
-	u16 xgxs_config_rx[4]; /* preemphasis values for the rx side */
-	u16 xgxs_config_tx[4]; /* preemphasis values for the tx side */
-
 	u32 feature_config_flags;
 #define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
 #define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY	(1<<2)
-#define FEATURE_CONFIG_BCM8727_NOC			(1<<3)
 	/* Will be populated during common init */
 	struct bnx2x_phy phy[MAX_PHYS];
 
 	/* Will be populated during common init */
 	u8 num_phys;
 
+	u8 rsrv;
+	u16 hw_led_mode; /* part of the hw_config read from the shmem */
+
 	/* Device pointer passed to all callback functions */
 	struct bnx2x *bp;
 };