Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull media updates from Mauro Carvalho Chehab:
 - V4L2 API additions to better support JPEG compression control
 - media API additions to properly support MPEG decoders
 - V4L2 API additions for image crop/scaling
 - a few other V4L2 API DocBook fixes/improvements
 - two new DVB frontend drivers: m88rs2000 and rtl2830
 - two new DVB drivers: az6007 and rtl28xxu
 - a framework for ISA drivers, that removed lots of common code found
   at the ISA radio drivers
 - a new FM transmitter driver (radio-keene)
 - a GPIO-based IR receiver driver
 - a new sensor driver: mt9m032
 - some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
   vs6624
 - several new board additions, driver fixes, improvements and cleanups.

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
  [media] update CARDLIST.em28xx
  [media] partially reverts changeset fa5527c
  [media] stb0899: fix the limits for signal strength values
  [media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
  [media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
  [media] -EINVAL -> -ENOTTY
  [media] gspca - sn9c20x: Cleanup source
  [media] gspca - sn9c20x: Simplify register write for capture start/stop
  [media] gspca - sn9c20x: Add automatic JPEG compression mechanism
  [media] gspca - sn9c20x: Greater delay in case of sensor no response
  [media] gspca - sn9c20x: Optimize the code of write sequences
  [media] gspca - sn9c20x: Add the JPEG compression quality control
  [media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
  [media] gspca - sn9c20x: Propagate USB errors to higher level
  [media] gspca - sn9c20x: Use the new video control mechanism
  [media] gspca - sn9c20x: Fix loss of frame start
  [media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
  [media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
  [media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
  [media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
  ...

1 files changed, 15 insertions, 8 deletions

diff --git a/drivers/media/dvb/frontends/drxk.h b/drivers/media/dvb/frontends/drxk.h
index 020981844a86..9d64e4fea066 100644
--- a/drivers/media/dvb/frontends/drxk.h
+++ b/drivers/media/dvb/frontends/drxk.h
@@ -7,15 +7,19 @@
 /**
  * struct drxk_config - Configure the initial parameters for DRX-K
  *
- * adr:			I2C Address of the DRX-K
- * parallel_ts:		true means that the device uses parallel TS,
+ * @adr:		I2C Address of the DRX-K
+ * @parallel_ts:	True means that the device uses parallel TS,
  * 			Serial otherwise.
- * single_master:	Device is on the single master mode
- * no_i2c_bridge:	Don't switch the I2C bridge to talk with tuner
- * antenna_gpio:	GPIO bit used to control the antenna
- * antenna_dvbt:	GPIO bit for changing antenna to DVB-C. A value of 1
+ * @dynamic_clk:	True means that the clock will be dynamically
+ *			adjusted. Static clock otherwise.
+ * @enable_merr_cfg:	Enable SIO_PDR_PERR_CFG/SIO_PDR_MVAL_CFG.
+ * @single_master:	Device is on the single master mode
+ * @no_i2c_bridge:	Don't switch the I2C bridge to talk with tuner
+ * @antenna_gpio:	GPIO bit used to control the antenna
+ * @antenna_dvbt:	GPIO bit for changing antenna to DVB-C. A value of 1
  *			means that 1=DVBC, 0 = DVBT. Zero means the opposite.
- * microcode_name:	Name of the firmware file with the microcode
+ * @mpeg_out_clk_strength: DRXK Mpeg output clock drive strength.
+ * @microcode_name:	Name of the firmware file with the microcode
  *
  * On the *_gpio vars, bit 0 is UIO-1, bit 1 is UIO-2 and bit 2 is
  * UIO-3.
@@ -25,11 +29,14 @@ struct drxk_config {
 	bool	single_master;
 	bool	no_i2c_bridge;
 	bool	parallel_ts;
+	bool	dynamic_clk;
+	bool	enable_merr_cfg;
 
 	bool	antenna_dvbt;
 	u16	antenna_gpio;
 
-	int    chunk_size;
+	u8	mpeg_out_clk_strength;
+	int	chunk_size;
 
 	const char *microcode_name;
 };