Pull release into acpica branch

1 files changed, 111 insertions, 0 deletions

diff --git a/arch/ppc/platforms/4xx/yucca.h b/arch/ppc/platforms/4xx/yucca.h
new file mode 100644
index 000000000000..01a4afea1514
--- /dev/null
+++ b/arch/ppc/platforms/4xx/yucca.h
@@ -0,0 +1,111 @@
+/*
+ * arch/ppc/platforms/4xx/yucca.h
+ *
+ * Yucca board definitions
+ *
+ * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter)
+ *
+ * Copyright 2004-2005 MontaVista Software Inc.
+ * Copyright (c) 2005 Cisco Systems.  All rights reserved.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASM_YUCCA_H__
+#define __ASM_YUCCA_H__
+
+#include <linux/config.h>
+#include <platforms/4xx/ppc440spe.h>
+
+/* F/W TLB mapping used in bootloader glue to reset EMAC */
+#define PPC44x_EMAC0_MR0	0xa0000800
+
+/* Location of MAC addresses in PIBS image */
+#define PIBS_FLASH_BASE		0xffe00000
+#define PIBS_MAC_BASE		(PIBS_FLASH_BASE+0x1b0400)
+
+/* External timer clock frequency */
+#define YUCCA_TMR_CLK		25000000
+
+/*
+ * FPGA registers
+ */
+#define YUCCA_FPGA_REG_BASE			0x00000004e2000000ULL
+#define YUCCA_FPGA_REG_SIZE			0x24
+
+#define FPGA_REG1A				0x1a
+
+#define FPGA_REG1A_PE0_GLED			0x8000
+#define FPGA_REG1A_PE1_GLED			0x4000
+#define FPGA_REG1A_PE2_GLED			0x2000
+#define FPGA_REG1A_PE0_YLED			0x1000
+#define FPGA_REG1A_PE1_YLED			0x0800
+#define FPGA_REG1A_PE2_YLED			0x0400
+#define FPGA_REG1A_PE0_PWRON			0x0200
+#define FPGA_REG1A_PE1_PWRON			0x0100
+#define FPGA_REG1A_PE2_PWRON			0x0080
+#define FPGA_REG1A_PE0_REFCLK_ENABLE		0x0040
+#define FPGA_REG1A_PE1_REFCLK_ENABLE		0x0020
+#define FPGA_REG1A_PE2_REFCLK_ENABLE		0x0010
+#define FPGA_REG1A_PE_SPREAD0			0x0008
+#define FPGA_REG1A_PE_SPREAD1			0x0004
+#define FPGA_REG1A_PE_SELSOURCE_0		0x0002
+#define FPGA_REG1A_PE_SELSOURCE_1		0x0001
+
+#define FPGA_REG1C				0x1c
+
+#define FPGA_REG1C_PE0_ROOTPOINT		0x8000
+#define FPGA_REG1C_PE1_ENDPOINT			0x4000
+#define FPGA_REG1C_PE2_ENDPOINT			0x2000
+#define FPGA_REG1C_PE0_PRSNT			0x1000
+#define FPGA_REG1C_PE1_PRSNT			0x0800
+#define FPGA_REG1C_PE2_PRSNT			0x0400
+#define FPGA_REG1C_PE0_WAKE			0x0080
+#define FPGA_REG1C_PE1_WAKE			0x0040
+#define FPGA_REG1C_PE2_WAKE			0x0020
+#define FPGA_REG1C_PE0_PERST			0x0010
+#define FPGA_REG1C_PE1_PERST			0x0008
+#define FPGA_REG1C_PE2_PERST			0x0004
+
+/*
+ * Serial port defines
+ */
+#define RS_TABLE_SIZE	3
+
+/* PIBS defined UART mappings, used before early_serial_setup */
+#define UART0_IO_BASE	0xa0000200
+#define UART1_IO_BASE	0xa0000300
+#define UART2_IO_BASE	0xa0000600
+
+#define BASE_BAUD	11059200
+#define STD_UART_OP(num)					\
+	{ 0, BASE_BAUD, 0, UART##num##_INT,			\
+		(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST),	\
+		iomem_base: (void*)UART##num##_IO_BASE,		\
+		io_type: SERIAL_IO_MEM},
+
+#define SERIAL_PORT_DFNS	\
+	STD_UART_OP(0)		\
+	STD_UART_OP(1)		\
+	STD_UART_OP(2)
+
+/* PCI support */
+#define YUCCA_PCIX_LOWER_IO	0x00000000
+#define YUCCA_PCIX_UPPER_IO	0x0000ffff
+#define YUCCA_PCIX_LOWER_MEM	0x80000000
+#define YUCCA_PCIX_UPPER_MEM	0x8fffffff
+#define YUCCA_PCIE_LOWER_MEM	0x90000000
+#define YUCCA_PCIE_MEM_SIZE	0x10000000
+
+#define YUCCA_PCIX_MEM_SIZE	0x10000000
+#define YUCCA_PCIX_MEM_OFFSET	0x00000000
+#define YUCCA_PCIE_MEM_SIZE	0x10000000
+#define YUCCA_PCIE_MEM_OFFSET	0x00000000
+
+#endif				/* __ASM_YUCCA_H__ */
+#endif				/* __KERNEL__ */