Merge branch 'remotes/lorenzo/pci/meson'

  - Fix meson PERST# GPIO polarity problem (Remi Pommarel)

  - Add DT bindings for Amlogic Meson G12A (Neil Armstrong)

  - Fix meson clock names to match DT bindings (Neil Armstrong)

  - Add meson support for Amlogic G12A SoC with separate shared PHY (Neil
    Armstrong)

  - Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe combo
    PHY (Neil Armstrong)

  - Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)

  - Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT (Neil
    Armstrong)

* remotes/lorenzo/pci/meson:
  arm64: dts: khadas-vim3: add commented support for PCIe
  arm64: dts: meson-g12a: Add PCIe node
  phy: meson-g12a-usb3-pcie: Add support for PCIe mode
  PCI: amlogic: meson: Add support for G12A
  PCI: amlogic: Fix probed clock names
  dt-bindings: pci: amlogic, meson-pcie: Add G12A bindings
  PCI: amlogic: Fix reset assertion via gpio descriptor

6 files changed, 116 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 3f39e020f74e..7ab71172cd3c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -95,6 +95,39 @@
 		#size-cells = <2>;
 		ranges;
 
+		pcie: pcie@fc000000 {
+			compatible = "amlogic,g12a-pcie", "snps,dw-pcie";
+			reg = <0x0 0xfc000000 0x0 0x400000
+			       0x0 0xff648000 0x0 0x2000
+			       0x0 0xfc400000 0x0 0x200000>;
+			reg-names = "elbi", "cfg", "config";
+			interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000
+				  0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>;
+
+			clocks = <&clkc CLKID_PCIE_PHY
+				  &clkc CLKID_PCIE_COMB
+				  &clkc CLKID_PCIE_PLL>;
+			clock-names = "general",
+				      "pclk",
+				      "port";
+			resets = <&reset RESET_PCIE_CTRL_A>,
+				 <&reset RESET_PCIE_APB>;
+			reset-names = "port",
+				      "apb";
+			num-lanes = <1>;
+			phys = <&usb3_pcie_phy PHY_TYPE_PCIE>;
+			phy-names = "pcie";
+			status = "disabled";
+		};
+
 		ethmac: ethernet@ff3f0000 {
 			compatible = "amlogic,meson-axg-dwmac",
 				     "snps,dwmac-3.70a",
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
index 3a6a1e0c1e32..124a80901084 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
index b73deb282120..bba98f982ad6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
index 8647da7d6609..eac5720dc15f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
@@ -246,6 +246,10 @@
 	linux,rc-map-name = "rc-khadas";
 };
 
+&pcie {
+	reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
+};
+
 &pwm_ef {
         status = "okay";
         pinctrl-0 = <&pwm_e_pins>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
index 5233bd7cacfb..dbbf29a0dbf6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
@@ -68,3 +68,28 @@
 	clock-names = "clkin1";
 	status = "okay";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
index 521573f3a5ba..256ea0349ffc 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
@@ -134,6 +134,10 @@
 	power-domains = <&pwrc PWRC_SM1_ETH_ID>;
 };
 
+&pcie {
+	power-domains = <&pwrc PWRC_SM1_PCIE_ID>;
+};
+
 &pwrc {
 	compatible = "amlogic,meson-sm1-pwrc";
 };