Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

power management changes for omap and imx

A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.

* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
  ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
  ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
  ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
  ARM: imx6q: build pm code only when CONFIG_PM selected
  ARM: mx5: use generic irq chip pm interface for pm functions on
  ARM: omap: pass minimal SoC/board data for UART from dt
  arm/dts: Add minimal device tree support for omap2420 and omap2430
  omap-serial: Add minimal device tree support
  omap-serial: Use default clock speed (48Mhz) if not specified
  omap-serial: Get rid of all pdev->id usage
  ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
  ARM: OMAP4: PRM: use PRCM interrupt handler
  ARM: OMAP3: pm: use prcm chain handler
  ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
  ARM: OMAP2+: mux: add support for PAD wakeup interrupts
  ARM: OMAP: PRCM: add suspend prepare / finish support
  ARM: OMAP: PRCM: add support for chain interrupt handler
  ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
  ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
  ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
  ...

1 files changed, 1 insertions, 99 deletions

diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 9996334cb687..383717ba63b9 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -475,106 +475,8 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
-
-static struct omap_device_pad serial1_pads[] __initdata = {
-	/*
-	 * Note that off output enable is an active low
-	 * signal. So setting this means pin is a
-	 * input enabled in off mode
-	 */
-	OMAP_MUX_STATIC("uart1_cts.uart1_cts",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rts.uart1_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rx.uart1_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_tx.uart1_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLDOWN |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial1_data __initdata = {
-	.id		= 0,
-	.pads		= serial1_pads,
-	.pads_cnt	= ARRAY_SIZE(serial1_pads),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init_port(&serial1_data);
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /*
@@ -711,7 +613,7 @@ static void __init omap_3430sdp_init(void)
 	else
 		gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 	omap_ads7846_init(1, gpio_pendown, 310, NULL);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(hyb18m512160af6_sdrc_params, NULL);
 	usb_musb_init(NULL);
 	board_smc91x_init();