Merge tag 'imx-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt

i.MX arm32 device tree changes for 6.4:

- New board device trees: Tolino Vison, chargebyte Tarragon,
  new revision of the IOTA board.
- A couple of imx7d-remarkable2 update to enable cyttsp5 touch and
  BD71815 PMIC.
- A series from Oleksij Rempel to configure Ethernet reference clock
  from device tree.
- A series from Stefan Wahren to use label references for i.MX28 based
  boards.

* tag 'imx-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (31 commits)
  ARM: dts: imx6ull: Add chargebyte Tarragon support
  ARM: dts: imx: Add devicetree for Tolino Vison
  ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board
  ARM: dts: imx6dl-yapp4: Remove unneeded status "okay"
  ARM: dts: imx6dl-yapp4: Move status to the end of property list
  ARM: dts: imx6dl-yapp4: Move phy reset into switch node
  ARM: dts: imx28-tx28: add SPDX-License-Identifier
  ARM: dts: imx28-ts4600: Convert to use label references
  ARM: dts: imx28-evk: Convert to use label references
  ARM: dts: imx28-duckbill-2: Include base board
  ARM: dts: imx28-duckbill: Convert to use label references
  ARM: dts: imx28-cfa10036: Convert to use label references
  ARM: dts: imx28-apx4devkit: Convert to use label references
  ARM: dts: imx28-m28/sps1: Convert to use label references
  ARM: dts: imx28-apf28: Convert to use label references
  ARM: dts: imx7d-remarkable2: Enable the rohm,bd71815
  ARM: dts: imx7d-remarkable2: Enable the cyttsp5
  ARM: dts: imx6dl-yapp4: Use reset-gpios property name
  ARM: dts: imx6ul-prti6g: configure ethernet reference clock parent
  ARM: dts: imx6ul: set enet_clk_ref to CLK_ENETx_REF_SEL
  ...

Link: https://lore.kernel.org/r/20230408101928.280271-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

48 files changed, 4852 insertions, 2793 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d092993864f3..eae9dcc2c138 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -561,7 +561,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-wandboard-revd1.dtb \
 	imx6dl-yapp4-draco.dtb \
 	imx6dl-yapp4-hydra.dtb \
+	imx6dl-yapp4-lynx.dtb \
 	imx6dl-yapp4-orion.dtb \
+	imx6dl-yapp4-phoenix.dtb \
 	imx6dl-yapp4-ursa.dtb \
 	imx6q-apalis-eval.dtb \
 	imx6q-apalis-ixora.dtb \
@@ -668,6 +670,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-wandboard-revb1.dtb \
 	imx6q-wandboard-revd1.dtb \
 	imx6q-yapp4-crux.dtb \
+	imx6q-yapp4-pegasus.dtb \
 	imx6q-zii-rdu2.dtb \
 	imx6qp-mba6b.dtb \
 	imx6qp-nitrogen6_max.dtb \
@@ -683,6 +686,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6qp-vicutp.dtb \
 	imx6qp-wandboard-revd1.dtb \
 	imx6qp-yapp4-crux-plus.dtb \
+	imx6qp-yapp4-pegasus-plus.dtb \
 	imx6qp-zii-rdu2.dtb \
 	imx6s-dhcom-drc02.dtb
 dtb-$(CONFIG_SOC_IMX6SL) += \
@@ -690,6 +694,7 @@ dtb-$(CONFIG_SOC_IMX6SL) += \
 	imx6sl-kobo-aura2.dtb \
 	imx6sl-tolino-shine2hd.dtb \
 	imx6sl-tolino-shine3.dtb \
+	imx6sl-tolino-vision.dtb \
 	imx6sl-tolino-vision5.dtb \
 	imx6sl-warp.dtb
 dtb-$(CONFIG_SOC_IMX6SLL) += \
@@ -755,6 +760,10 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ull-phytec-segin-lc-rdk-nand.dtb \
 	imx6ull-phytec-tauri-emmc.dtb \
 	imx6ull-phytec-tauri-nand.dtb \
+	imx6ull-tarragon-master.dtb \
+	imx6ull-tarragon-micro.dtb \
+	imx6ull-tarragon-slave.dtb \
+	imx6ull-tarragon-slavext.dtb \
 	imx6ull-tqma6ull2-mba6ulx.dtb \
 	imx6ull-tqma6ull2l-mba6ulx.dtb \
 	imx6ulz-14x14-evk.dtb \
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
index 14a92fe59770..98672932e41b 100644
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ b/arch/arm/boot/dts/imx28-apf28.dts
@@ -14,67 +14,59 @@
 		device_type = "memory";
 		reg = <0x40000000 0x08000000>;
 	};
+};
 
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-
-				partition@0 {
-					label = "u-boot";
-					reg = <0x0 0x300000>;
-				};
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
 
-				partition@300000 {
-					label = "env";
-					reg = <0x300000 0x80000>;
-				};
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
 
-				partition@380000 {
-					label = "env2";
-					reg = <0x380000 0x80000>;
-				};
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0 0x300000>;
+	};
 
-				partition@400000 {
-					label = "dtb";
-					reg = <0x400000 0x80000>;
-				};
+	partition@300000 {
+		label = "env";
+		reg = <0x300000 0x80000>;
+	};
 
-				partition@480000 {
-					label = "splash";
-					reg = <0x480000 0x80000>;
-				};
+	partition@380000 {
+		label = "env2";
+		reg = <0x380000 0x80000>;
+	};
 
-				partition@500000 {
-					label = "kernel";
-					reg = <0x500000 0x800000>;
-				};
+	partition@400000 {
+		label = "dtb";
+		reg = <0x400000 0x80000>;
+	};
 
-				partition@d00000 {
-					label = "rootfs";
-					reg = <0xd00000 0xf300000>;
-				};
-			};
-		};
+	partition@480000 {
+		label = "splash";
+		reg = <0x480000 0x80000>;
+	};
 
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-		};
+	partition@500000 {
+		label = "kernel";
+		reg = <0x500000 0x800000>;
 	};
 
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			status = "okay";
-		};
+	partition@d00000 {
+		label = "rootfs";
+		reg = <0xd00000 0xf300000>;
 	};
 };
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index 1b253b47006c..4704b6141836 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -10,166 +10,6 @@
 	model = "Armadeus Systems APF28Dev docking/development board";
 	compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
 
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_apf28dev>;
-
-				hog_pins_apf28dev: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D16__GPIO_1_16
-						MX28_PAD_LCD_D17__GPIO_1_17
-						MX28_PAD_LCD_D18__GPIO_1_18
-						MX28_PAD_LCD_D19__GPIO_1_19
-						MX28_PAD_LCD_D20__GPIO_1_20
-						MX28_PAD_LCD_D21__GPIO_1_21
-						MX28_PAD_LCD_D22__GPIO_1_22
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apf28dev: lcdif-apf28dev@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				usb0_otg_apf28dev: otg-apf28dev@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D23__GPIO_1_23
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_16bit_pins_a
-						&lcdif_pins_apf28dev>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <16>;
-					bus-width = <16>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33000033>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <96>;
-							hfront-porch = <96>;
-							vback-porch = <20>;
-							vfront-porch = <21>;
-							hsync-len = <64>;
-							vsync-len = <4>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				xceiver-supply = <&reg_can0_vcc>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				uart-has-rtscts;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_otg_apf28dev
-					&usb0_id_pins_b>;
-			vbus-supply = <&reg_usb0_vbus>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -223,3 +63,155 @@
 		};
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	xceiver-supply = <&reg_can0_vcc>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_16bit_pins_a
+		     &lcdif_pins_apf28dev>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <16>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33000033>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <96>;
+				hfront-porch = <96>;
+				vback-porch = <20>;
+				vfront-porch = <21>;
+				hsync-len = <64>;
+				vsync-len = <4>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_apf28dev>;
+
+	hog_pins_apf28dev: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D16__GPIO_1_16
+			MX28_PAD_LCD_D17__GPIO_1_17
+			MX28_PAD_LCD_D18__GPIO_1_18
+			MX28_PAD_LCD_D19__GPIO_1_19
+			MX28_PAD_LCD_D20__GPIO_1_20
+			MX28_PAD_LCD_D21__GPIO_1_21
+			MX28_PAD_LCD_D22__GPIO_1_22
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apf28dev: lcdif-apf28dev@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	usb0_otg_apf28dev: otg-apf28dev@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D23__GPIO_1_23
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_otg_apf28dev
+		     &usb0_id_pins_b>;
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index b86be320496b..f9bf40d96568 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -11,200 +11,6 @@
 		reg = <0x40000000 0x04000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_RDY1__GPIO_0_21
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_JTAG_RTCK__GPIO_4_20
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apx4: lcdif-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA4__SSP2_D0
-						MX28_PAD_SSP0_DATA5__SSP2_D3
-						MX28_PAD_SSP0_DATA6__SSP2_CMD
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-						MX28_PAD_SSP2_SS1__SSP2_D1
-						MX28_PAD_SSP2_SS2__SSP2_D2
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-					>;
-					fsl,drive-strength = <MXS_DRIVE_12mA>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_apx4>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <88>;
-							hfront-porch = <40>;
-							vback-porch = <32>;
-							vfront-porch = <13>;
-							hsync-len = <48>;
-							vsync-len = <3>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				pcf8563: rtc@51 {
-					compatible = "phg,pcf8563";
-					reg = <0x51>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_2pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&usb1_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-		      status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -238,3 +44,189 @@
 		};
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_2pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_apx4>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <88>;
+				hfront-porch = <40>;
+				vback-porch = <32>;
+				vfront-porch = <13>;
+				hsync-len = <48>;
+				vsync-len = <3>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "phg,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_RDY1__GPIO_0_21
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_JTAG_RTCK__GPIO_4_20
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apx4: lcdif-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA4__SSP2_D0
+			MX28_PAD_SSP0_DATA5__SSP2_D3
+			MX28_PAD_SSP0_DATA6__SSP2_CMD
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+			MX28_PAD_SSP2_SS1__SSP2_D1
+			MX28_PAD_SSP2_SS2__SSP2_D2
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_12mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb1 {
+      status = "okay";
+};
+
+&usbphy1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 85aa1cc3ff66..d004b1cbb4ae 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -16,107 +16,6 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				ssd1306_cfa10036: ssd1306-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__GPIO_2_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins_cfa10036: leds-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_RX__GPIO_3_4
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				usb0_otg_cfa10036: otg-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_RDY0__USB0_ID
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x31c3 /*
-						MX28_PAD_PWM3__GPIO_3_28 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
-				};
-
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				bus-width = <4>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_b>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_b>;
-				clock-frequency = <400000>;
-				status = "okay";
-
-				ssd1306: oled@3c {
-					compatible = "solomon,ssd1306fb-i2c";
-					pinctrl-names = "default";
-					pinctrl-0 = <&ssd1306_cfa10036>;
-					reg = <0x3c>;
-					reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-					solomon,height = <32>;
-					solomon,width = <128>;
-					solomon,page-offset = <0>;
-					solomon,com-lrremap;
-					solomon,com-invdir;
-					solomon,com-offset = <32>;
-				};
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_otg_cfa10036>;
-			dr_mode = "peripheral";
-			phy_type = "utmi";
-			status = "okay";
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -138,3 +37,95 @@
 		gpio = <&gpio3 28 0>;
 	};
 };
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_b>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ssd1306: oled@3c {
+		compatible = "solomon,ssd1306fb-i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ssd1306_cfa10036>;
+		reg = <0x3c>;
+		reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+		solomon,height = <32>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,com-lrremap;
+		solomon,com-invdir;
+		solomon,com-offset = <32>;
+	};
+};
+
+&pinctrl {
+	ssd1306_cfa10036: ssd1306-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins_cfa10036: leds-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_RX__GPIO_3_4
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	usb0_otg_cfa10036: otg-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY0__USB0_ID
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			0x31c3 /*
+			MX28_PAD_PWM3__GPIO_3_28 */
+		>;
+		fsl,drive-strength = <0>;
+		fsl,voltage = <1>;
+		fsl,pull-up = <0>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_otg_cfa10036>;
+	dr_mode = "peripheral";
+	phy_type = "utmi";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 9ef0d567ea48..94d6614c1983 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -78,226 +78,6 @@
 		};
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10049: usb-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				i2cmux_pins_cfa10049: i2cmux-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D22__GPIO_1_22
-						MX28_PAD_LCD_D23__GPIO_1_23
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_pins_cfa10049: mac0-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS2__GPIO_2_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				pca_pins_cfa10049: pca-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS0__GPIO_2_19
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				rotary_pins_cfa10049: rotary-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF1_SDATA0__GPIO_3_26
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				spi2_pins_cfa10049: spi2-cfa10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				spi3_pins_cfa10049: spi3-cfa10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_RDN__GPIO_0_24
-						MX28_PAD_GPMI_RESETN__GPIO_0_28
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_ALE__GPIO_0_26
-						MX28_PAD_GPMI_CLE__GPIO_0_27
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10049: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				w1_gpio_pins: w1-gpio@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D21__GPIO_1_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
-					     &lcdif_pins_cfa10049
-					     &lcdif_pins_cfa10049_pullup>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9216000>;
-							hactive = <320>;
-							vactive = <480>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <15>;
-							vsync-len = <15>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-
-			i2c1: i2c@8005a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c1_pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -315,18 +95,6 @@
 		};
 	};
 
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a
-				&mac0_pins_cfa10049>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
 	spi-2 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
@@ -426,3 +194,225 @@
 		gpios = <&gpio1 21 0>;
 	};
 };
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10049
+		     &lcdif_pins_cfa10049
+		     &lcdif_pins_cfa10049_pullup>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9216000>;
+				hactive = <320>;
+				vactive = <480>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <15>;
+				vsync-len = <15>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a
+		&mac0_pins_cfa10049>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10049: usb-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	i2cmux_pins_cfa10049: i2cmux-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D22__GPIO_1_22
+			MX28_PAD_LCD_D23__GPIO_1_23
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_pins_cfa10049: mac0-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	pca_pins_cfa10049: pca-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS0__GPIO_2_19
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	rotary_pins_cfa10049: rotary-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_I2C0_SCL__GPIO_3_24
+			MX28_PAD_I2C0_SDA__GPIO_3_25
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SAIF1_SDATA0__GPIO_3_26
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	spi2_pins_cfa10049: spi2-cfa10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	spi3_pins_cfa10049: spi3-cfa10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_GPMI_RESETN__GPIO_0_28
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_ALE__GPIO_0_26
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10049: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	w1_gpio_pins: w1-gpio@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D21__GPIO_1_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index fac5bbda7a93..42ba7da48beb 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -14,121 +14,6 @@
 	model = "Crystalfontz CFA-10055 Board";
 	compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				spi2_pins_cfa10055: spi2-cfa10055@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10055: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10055
-					     &lcdif_pins_cfa10055
-					     &lcdif_pins_cfa10055_pullup>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9216000>;
-							hactive = <320>;
-							vactive = <480>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <15>;
-							vsync-len = <15>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-		};
-	};
-
 	spi-2 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
@@ -159,3 +44,112 @@
 		default-brightness-level = <6>;
 	};
 };
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10055
+		     &lcdif_pins_cfa10055
+		     &lcdif_pins_cfa10055_pullup>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9216000>;
+				hactive = <320>;
+				vactive = <480>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <15>;
+				vsync-len = <15>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&pinctrl {
+	spi2_pins_cfa10055: spi2-cfa10055@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10055: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index c5f3337e8b39..0e15bdfd7281 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -13,81 +13,6 @@
 	model = "Crystalfontz CFA-10056 Board";
 	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				spi2_pins_cfa10056: spi2-cfa10056@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_pins_cfa10056: lcdif-10056@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-						&lcdif_pins_cfa10056
-						&lcdif_pins_cfa10056_pullup >;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <32000000>;
-							hactive = <480>;
-							vactive = <800>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <5>;
-							vsync-len = <5>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-	};
-
 	spi-2 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
@@ -111,3 +36,74 @@
 		};
 	};
 };
+
+&pinctrl {
+	spi2_pins_cfa10056: spi2-cfa10056@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_pins_cfa10056: lcdif-10056@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+			&lcdif_pins_cfa10056
+			&lcdif_pins_cfa10056_pullup >;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <32000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <5>;
+				vsync-len = <5>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 2f7e479dbc74..27602c01f162 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -14,126 +14,6 @@
 	model = "Crystalfontz CFA-10057 Board";
 	compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10057: usb-10057@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10057: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10057
-					     &lcdif_pins_cfa10057>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <480>;
-							vactive = <800>;
-							hfront-porch = <12>;
-							hback-porch = <2>;
-							vfront-porch = <5>;
-							vback-porch = <3>;
-							hsync-len = <2>;
-							vsync-len = <2>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-
-			i2c1: i2c@8005a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c1_pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -151,17 +31,6 @@
 		};
 	};
 
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
 	backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 4 5000000>;
@@ -169,3 +38,124 @@
 		default-brightness-level = <7>;
 	};
 };
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10057
+		     &lcdif_pins_cfa10057>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hfront-porch = <12>;
+				hback-porch = <2>;
+				vfront-porch = <5>;
+				vback-porch = <3>;
+				hsync-len = <2>;
+				vsync-len = <2>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10057: usb-10057@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10057: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 4465fd86785a..931c4d089b26 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -14,93 +14,6 @@
 	model = "Crystalfontz CFA-10058 Board";
 	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10058: usb-10058@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10058: lcdif-10058@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-						 &lcdif_pins_cfa10058>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <40>;
-							hfront-porch = <40>;
-							vback-porch = <13>;
-							vfront-porch = <29>;
-							hsync-len = <8>;
-							vsync-len = <8>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -118,17 +31,6 @@
 		};
 	};
 
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
 	backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 3 5000000>;
@@ -136,3 +38,91 @@
 		default-brightness-level = <6>;
 	};
 };
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+			 &lcdif_pins_cfa10058>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <40>;
+				hfront-porch = <40>;
+				vback-porch = <13>;
+				vfront-porch = <29>;
+				hsync-len = <8>;
+				vsync-len = <8>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10058: usb-10058@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10058: lcdif-10058@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
index d451fa018d83..b73020ff1053 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-485.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
@@ -5,172 +5,13 @@
  */
 
 /dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
 
 / {
 	model = "I2SE Duckbill 2 485";
 	compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
 
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
 		rs485-red {
 			label = "duckbill:red:rs485";
 			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
@@ -182,3 +23,16 @@
 		};
 	};
 };
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
index 73f521c46c1e..473d99b9b42f 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
@@ -5,184 +5,14 @@
  */
 
 /dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
 
 / {
 	model = "I2SE Duckbill 2 EnOcean";
 	compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
 
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_AUART0_CTS__GPIO_3_2
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				enocean_button: enocean-button@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
 		enocean-blue {
 			label = "duckbill:blue:enocean";
 			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
@@ -211,3 +41,29 @@
 		};
 	};
 };
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_AUART0_CTS__GPIO_3_2
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
+
+&pinctrl {
+	enocean_button: enocean-button@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
index 0e8be5975709..859d97a5a775 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
@@ -5,9 +5,7 @@
  */
 
 /dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
 
 / {
 	model = "I2SE Duckbill 2 SPI";
@@ -16,179 +14,50 @@
 	aliases {
 		ethernet1 = &qca7000;
 	};
+};
 
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				qca7000: ethernet@0 {
-					reg = <0>;
-					compatible = "qca,qca7000";
-					pinctrl-names = "default";
-					pinctrl-0 = <&qca7000_pins>;
-					interrupt-parent = <&gpio3>;
-					interrupts = <3 IRQ_TYPE_EDGE_RISING>;
-					spi-cpha;
-					spi-cpol;
-					spi-max-frequency = <8000000>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: led@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				qca7000_pins: qca7000@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
-						MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
-						MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
-						MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
-						MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
-						MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
+&auart0 {
+	status = "disabled";
+};
 
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
+&i2c0 {
+	status = "disabled";
+};
 
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
+&pinctrl {
+	qca7000_pins: qca7000@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
+			MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
+			MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
+			MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
+			MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
+			MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
 	};
+};
 
-	leds {
-		compatible = "gpio-leds";
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	/delete-property/ bus-width;
+	/delete-property/ vmmc-supply;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		reg = <0>;
+		compatible = "qca,qca7000";
 		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
+		pinctrl-0 = <&qca7000_pins>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <8000000>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts
index 23fd3036404d..4e28212e9626 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2.dts
@@ -18,138 +18,6 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "3P3V";
@@ -176,3 +44,127 @@
 		};
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+	phy-supply = <&reg_3p3v>;
+	phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_phy_int_pin>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			max-speed = <100>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_reset_pin: mac0-phy-reset@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_int_pin: mac0-phy-int@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SAIF0_MCLK__GPIO_3_20
+			MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+	non-removable;
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_b
+		&mmc2_cd_cfg &mmc2_sck_cfg_b>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
index c666afb12445..13ffd533fdea 100644
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ b/arch/arm/boot/dts/imx28-duckbill.dts
@@ -17,108 +17,6 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_RX__GPIO_3_4
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			status = "okay";
-		};
-	};
-
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "3P3V";
@@ -145,3 +43,97 @@
 		};
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+	phy-supply = <&reg_3p3v>;
+	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_reset_pin: mac0-phy-reset@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_RX__GPIO_3_4
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 1053b7c584d8..783abb82b2a8 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -95,266 +95,258 @@
 		};
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
-					     &gpmi_pins_evk>;
-				status = "okay";
-			};
+	sound {
+		compatible = "fsl,imx28-evk-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "imx28-evk-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
 
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				wp-gpios = <&gpio2 12 0>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio3_5>;
 
-			ssp1: spi@80012000 {
-				compatible = "fsl,imx28-mmc";
-				bus-width = <8>;
-				wp-gpios = <&gpio0 28 0>;
-			};
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio3 5 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
 
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: flash@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "sst,sst25vf016b", "jedec,spi-nor";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
+	backlight_display: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 2 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
 
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP1_CMD__GPIO_2_13
-						MX28_PAD_SSP1_DATA3__GPIO_2_15
-						MX28_PAD_ENET0_RX_CLK__GPIO_4_13
-						MX28_PAD_SSP1_SCK__GPIO_2_12
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_AUART2_RX__GPIO_3_8
-						MX28_PAD_AUART2_TX__GPIO_3_9
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pin_gpio3_5: led_gpio3_5@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				gpmi_pins_evk: gpmi-nand-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPMI_CE1N
-						MX28_PAD_GPMI_RDY1__GPMI_READY1
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_evk: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
 
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_evk>;
-				status = "okay";
-
-				port {
-					display_out: endpoint {
-						remote-endpoint = <&panel_in>;
-					};
-				};
-			};
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_pins_a>;
+	status = "okay";
+};
 
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				xceiver-supply = <&reg_can_3v3>;
-				status = "okay";
-			};
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	xceiver-supply = <&reg_can_3v3>;
+	status = "okay";
+};
 
-			can1: can@80034000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can1_pins_a>;
-				xceiver-supply = <&reg_can_3v3>;
-				status = "okay";
-			};
-		};
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	xceiver-supply = <&reg_can_3v3>;
+	status = "okay";
+};
 
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
 
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+		     &gpmi_pins_evk>;
+	status = "okay";
+};
 
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-				fsl,ave-ctrl = <4>;
-				fsl,ave-delay = <2>;
-				fsl,settling = <10>;
-			};
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_evk>;
+	status = "okay";
 
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				at24@51 {
-					compatible = "atmel,24c32";
-					pagesize = <32>;
-					reg = <0x51>;
-				};
-			};
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
 
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
-				status = "okay";
-			};
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	fsl,ave-ctrl = <4>;
+	fsl,ave-delay = <2>;
+	fsl,settling = <10>;
+	status = "okay";
+};
 
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
 
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				uart-has-rtscts;
-				status = "okay";
-			};
+	at24@51 {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x51>;
+	};
+};
 
-			auart3: serial@80070000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_pins_a>;
-				status = "okay";
-			};
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-supply = <&reg_fec_3v3>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
 
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
 
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP1_CMD__GPIO_2_13
+			MX28_PAD_SSP1_DATA3__GPIO_2_15
+			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+			MX28_PAD_SSP1_SCK__GPIO_2_12
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_AUART2_RX__GPIO_3_8
+			MX28_PAD_AUART2_TX__GPIO_3_9
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
 	};
 
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_id_pins_a>;
-			vbus-supply = <&reg_usb0_vbus>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-supply = <&reg_fec_3v3>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
+	led_pin_gpio3_5: led_gpio3_5@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
 
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
+	gpmi_pins_evk: gpmi-nand-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPMI_CE1N
+			MX28_PAD_GPMI_RDY1__GPMI_READY1
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
 	};
 
-	sound {
-		compatible = "fsl,imx28-evk-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "imx28-evk-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
+	lcdif_pins_evk: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
 	};
+};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_gpio3_5>;
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2_pins_a>;
+	status = "okay";
+};
 
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio3 5 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
 
-	backlight_display: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <8>;
+	wp-gpios = <&gpio2 12 0>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp1 {
+	compatible = "fsl,imx28-mmc";
+	bus-width = <8>;
+	wp-gpios = <&gpio0 28 0>;
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
 	};
 };
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_pins_a>;
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-m28.dtsi b/arch/arm/boot/dts/imx28-m28.dtsi
index 2bdb4c093545..c08b14ad7cd5 100644
--- a/arch/arm/boot/dts/imx28-m28.dtsi
+++ b/arch/arm/boot/dts/imx28-m28.dtsi
@@ -14,31 +14,6 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				rtc: rtc@68 {
-					compatible = "st,m41t62";
-					reg = <0x68>;
-				};
-			};
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -54,3 +29,22 @@
 		};
 	};
 };
+
+&gpmi {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	rtc: rtc@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
index 865ac3d573c7..6b01de9efd02 100644
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ b/arch/arm/boot/dts/imx28-m28cu3.dts
@@ -15,187 +15,6 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-
-				partition@0 {
-					label = "gpmi-nfc-0-boot";
-					reg = <0x00000000 0x01400000>;
-					read-only;
-				};
-
-				partition@1 {
-					label = "gpmi-nfc-general-use";
-					reg = <0x01400000 0x0ec00000>;
-				};
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					     &mmc0_cd_cfg
-					     &mmc0_sck_cfg>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_a
-					     &mmc2_cd_cfg
-					     &mmc2_sck_cfg_a>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd1>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS0__GPIO_2_19
-						MX28_PAD_PWM4__GPIO_3_29
-						MX28_PAD_AUART2_RX__GPIO_3_8
-						MX28_PAD_ENET0_RX_CLK__GPIO_4_13
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_m28: lcdif-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_VSYNC__LCD_VSYNC
-						MX28_PAD_LCD_HSYNC__LCD_HSYNC
-						MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
-						MX28_PAD_LCD_RESET__LCD_RESET
-						MX28_PAD_LCD_CS__LCD_ENABLE
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins_gpio: leds-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP3_MISO__GPIO_2_26
-						MX28_PAD_SSP3_SCK__GPIO_2_24
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			ocotp@8002c000 {
-				status = "okay";
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_m28>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <6410256>;
-							hactive = <320>;
-							vactive = <240>;
-							hback-porch = <38>;
-							hfront-porch = <20>;
-							vback-porch = <15>;
-							vfront-porch = <5>;
-							hsync-len = <30>;
-							vsync-len = <3>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_b>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			auart3: serial@80070000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_2pins_b>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb1_pins_a>;
-			disable-over-current;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
 	backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 3 5000000>;
@@ -264,3 +83,176 @@
 		};
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_2pins_b>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&gpmi {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+
+	partition@0 {
+		label = "gpmi-nfc-0-boot";
+		reg = <0x00000000 0x01400000>;
+		read-only;
+	};
+
+	partition@1 {
+		label = "gpmi-nfc-general-use";
+		reg = <0x01400000 0x0ec00000>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_m28>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <6410256>;
+				hactive = <320>;
+				vactive = <240>;
+				hback-porch = <38>;
+				hfront-porch = <20>;
+				vback-porch = <15>;
+				vfront-porch = <5>;
+				hsync-len = <30>;
+				vsync-len = <3>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&ocotp {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS0__GPIO_2_19
+			MX28_PAD_PWM4__GPIO_3_29
+			MX28_PAD_AUART2_RX__GPIO_3_8
+			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_m28: lcdif-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_VSYNC__LCD_VSYNC
+			MX28_PAD_LCD_HSYNC__LCD_HSYNC
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_RESET__LCD_RESET
+			MX28_PAD_LCD_CS__LCD_ENABLE
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins_gpio: leds-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP3_MISO__GPIO_2_26
+			MX28_PAD_SSP3_SCK__GPIO_2_24
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_cd_cfg
+		     &mmc0_sck_cfg>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_a
+		     &mmc2_cd_cfg
+		     &mmc2_sck_cfg_a>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd1>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 13acdc7916b9..e350d57a4cec 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -11,220 +11,6 @@
 	model = "Aries/DENX M28EVK";
 	compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
 
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					     &mmc0_cd_cfg
-					     &mmc0_sck_cfg>;
-				bus-width = <8>;
-				wp-gpios = <&gpio3 10 0>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: flash@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "m25p80", "jedec,spi-nor";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_AUART2_CTS__GPIO_3_10
-						MX28_PAD_AUART2_RTS__GPIO_3_11
-						MX28_PAD_AUART3_RX__GPIO_3_12
-						MX28_PAD_AUART3_TX__GPIO_3_13
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_m28: lcdif-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
-						MX28_PAD_LCD_ENABLE__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_m28>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <16>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33260000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <0>;
-							hfront-porch = <256>;
-							vback-porch = <0>;
-							vfront-porch = <45>;
-							hsync-len = <1>;
-							vsync-len = <1>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				status = "okay";
-			};
-
-			can1: can@80034000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can1_pins_a>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				eeprom: eeprom@51 {
-					compatible = "atmel,24c128";
-					reg = <0x51>;
-					pagesize = <32>;
-				};
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_b>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			vbus-supply = <&reg_usb0_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_pins_a>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb1_pins_a>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			clocks = <&clks 57>, <&clks 57>;
-			clock-names = "ipg", "ahb";
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
 	backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 4 5000000>;
@@ -269,3 +55,209 @@
 		audio-codec = <&sgtl5000>;
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_b>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	eeprom: eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_m28>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33260000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <0>;
+				hfront-porch = <256>;
+				vback-porch = <0>;
+				vfront-porch = <45>;
+				hsync-len = <1>;
+				vsync-len = <1>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	status = "okay";
+	fsl,lradc-touchscreen-wires = <4>;
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	clocks = <&clks 57>, <&clks 57>;
+	clock-names = "ipg", "ahb";
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_AUART2_CTS__GPIO_3_10
+			MX28_PAD_AUART2_RTS__GPIO_3_11
+			MX28_PAD_AUART3_RX__GPIO_3_12
+			MX28_PAD_AUART3_TX__GPIO_3_13
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_m28: lcdif-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_ENABLE__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		     &mmc0_cd_cfg
+		     &mmc0_sck_cfg>;
+	bus-width = <8>;
+	wp-gpios = <&gpio3 10 0>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb0_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_a>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 90928db0df70..5d74a68c56ff 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -15,111 +15,6 @@
 		reg = <0x40000000 0x08000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog-gpios@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D00__GPIO_0_0
-						MX28_PAD_GPMI_D03__GPIO_0_3
-						MX28_PAD_GPMI_D06__GPIO_0_6
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: flash@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "everspin,mr25h256", "mr25h256";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				rtc: rtc@51 {
-					compatible = "nxp,pcf8563";
-					reg = <0x51>;
-				};
-
-				eeprom: eeprom@52 {
-					compatible = "atmel,24c64";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			vbus-supply = <&reg_usb0_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_pins_b>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -164,3 +59,99 @@
 
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog-gpios@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D06__GPIO_0_6
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "everspin,mr25h256", "mr25h256";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb0_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_b>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-ts4600.dts b/arch/arm/boot/dts/imx28-ts4600.dts
index 0d58da1c0cc5..ae6ed5c41be3 100644
--- a/arch/arm/boot/dts/imx28-ts4600.dts
+++ b/arch/arm/boot/dts/imx28-ts4600.dts
@@ -18,50 +18,6 @@
 		reg = <0x40000000 0x10000000>;   /* 256MB */
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					     &mmc0_sck_cfg
-					     &en_sd_pwr>;
-				broken-cd;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-
-				en_sd_pwr: en-sd-pwr@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_PWM3__GPIO_3_28
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-			};
-		};
-
-		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
 	reg_vddio_sd0: regulator-vddio-sd0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vddio-sd0";
@@ -72,3 +28,39 @@
 	};
 
 };
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	en_sd_pwr: en-sd-pwr@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_PWM3__GPIO_3_28
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_sck_cfg
+		     &en_sd_pwr>;
+	broken-cd;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts
index 096f246032c6..ffe58c7093e1 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/imx28-tx28.dts
@@ -1,43 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 /*
  * Copyright 2012 Shawn Guo <shawn.guo@linaro.org>
  * Copyright 2013-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/imx6dl-alti6p.dts b/arch/arm/boot/dts/imx6dl-alti6p.dts
index e8325fd680d9..e6a4e2770640 100644
--- a/arch/arm/boot/dts/imx6dl-alti6p.dts
+++ b/arch/arm/boot/dts/imx6dl-alti6p.dts
@@ -22,6 +22,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	i2c2-mux {
@@ -191,6 +192,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clock_ksz8081>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -208,10 +216,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clock_ksz8081>;
-	clock-names = "ipg", "ahb", "ptp";
 	status = "okay";
 
 	mdio {
diff --git a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts b/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
index 864dc5018451..33825b5a8f26 100644
--- a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
+++ b/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
@@ -28,6 +28,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_usb_h1_vbus: regulator-usb-h1-vbus {
@@ -64,6 +65,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&rmii_clk>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&rmii_clk>;
+};
+
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
@@ -297,11 +305,6 @@
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
 	phy-handle = <&phy>;
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&rmii_clk>,
-		 <&clks IMX6QDL_CLK_ENET_REF>;
-	clock-names = "ipg", "ahb", "ptp", "enet_out";
 	status = "okay";
 
 	mdio {
diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/imx6dl-lanmcu.dts
index 6b6e6fcdea9c..fa823988312d 100644
--- a/arch/arm/boot/dts/imx6dl-lanmcu.dts
+++ b/arch/arm/boot/dts/imx6dl-lanmcu.dts
@@ -21,6 +21,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	backlight: backlight {
@@ -109,14 +110,17 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clock_ksz8081>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clock_ksz8081>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rgmii_phy>;
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
index c52e6caf3996..e98046eea7a4 100644
--- a/arch/arm/boot/dts/imx6dl-plybas.dts
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -75,6 +75,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_5v0: regulator-5v0 {
@@ -99,6 +100,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -116,10 +124,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rgmii_phy>;
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 522660c912a0..e3c10483f33b 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -84,6 +84,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_3v3: regulator-3v3 {
@@ -173,6 +174,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -254,10 +262,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rgmii_phy>;
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6dl-prtmvt.dts b/arch/arm/boot/dts/imx6dl-prtmvt.dts
index 1f8cddd83ccb..5f4fa796ca18 100644
--- a/arch/arm/boot/dts/imx6dl-prtmvt.dts
+++ b/arch/arm/boot/dts/imx6dl-prtmvt.dts
@@ -193,6 +193,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_1v8: regulator-1v8 {
@@ -293,8 +294,10 @@
 };
 
 &clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>, <&clk50m_phy>;
 };
 
 &ecspi1 {
@@ -314,10 +317,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rmii_phy>;
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 72df1dba83be..23274be08e61 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -54,6 +54,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	rotary-encoder {
@@ -134,6 +135,13 @@
 	};
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &ecspi2 {
 	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -182,10 +190,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rmii_phy>;
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
index aacbf317feea..3be38a3c4bb1 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -98,7 +98,6 @@
 		regulator-max-microvolt = <5000000>;
 		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
-		status = "okay";
 	};
 };
 
@@ -106,8 +105,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <20>;
 	phy-supply = <&sw2_reg>;
 	status = "okay";
 
@@ -131,6 +128,7 @@
 		switch@10 {
 			compatible = "qca,qca8334";
 			reg = <10>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 
 			switch_ports: ports {
 				#address-cells = <1>;
@@ -270,9 +268,9 @@
 		compatible = "ti,lp5562";
 		reg = <0x30>;
 		clock-mode = /bits/ 8 <1>;
-		status = "disabled";
 		#address-cells = <1>;
 		#size-cells = <0>;
+		status = "disabled";
 
 		led@0 {
 			chan-name = "R";
@@ -303,7 +301,6 @@
 		compatible = "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <64>;
-		status = "okay";
 	};
 
 	touchscreen: touchscreen@5c {
@@ -313,7 +310,7 @@
 		interrupt-parent = <&gpio4>;
 		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
-		reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		touchscreen-size-x = <800>;
 		touchscreen-size-y = <480>;
 		status = "disabled";
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-lynx.dts b/arch/arm/boot/dts/imx6dl-yapp4-lynx.dts
new file mode 100644
index 000000000000..5c2cd517589b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-lynx.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Lynx i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-lynx", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-phoenix.dts b/arch/arm/boot/dts/imx6dl-yapp4-phoenix.dts
new file mode 100644
index 000000000000..e0292f11d03e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp4-phoenix.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Phoenix i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-phoenix", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
+
+&aliases {
+	/delete-property/ ethernet1;
+};
+
+&gpio_keys {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&switch_ports {
+	/delete-node/ port@2;
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp43-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp43-common.dtsi
new file mode 100644
index 000000000000..52a0f6ee426f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-yapp43-common.dtsi
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases: aliases {
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 32 64 128 255>;
+		default-brightness-level = <32>;
+		num-interpolated-steps = <8>;
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		button {
+			label = "Factory RESET";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	lcd_display: display {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel: panel {
+		compatible = "dataimage,scf0700c48ggu18";
+		power-supply = <&sw2_reg>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&sw2_reg>;
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@0 {
+			compatible = "marvell,mv88e6085";
+			reg = <0>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+
+			switch_ports: ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethphy0: port@0 {
+					reg = <0>;
+					label = "cpu";
+					phy-mode = "rgmii-id";
+					ethernet = <&fec>;
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				eth2: port@1 {
+					reg = <1>;
+					label = "eth2";
+					phy-handle = <&phy_port1>;
+				};
+
+				eth1: port@2 {
+					reg = <2>;
+					label = "eth1";
+					phy-handle = <&phy_port2>;
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_port1: switchphy@11 {
+					reg = <0x11>;
+				};
+
+				phy_port2: switchphy@12 {
+					reg = <0x12>;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze200";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x8>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vsnvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	leds: led-controller@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		clock-mode = /bits/ 8 <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		led@0 {
+			chan-name = "R";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+			reg = <0>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@1 {
+			chan-name = "G";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@2 {
+			chan-name = "B";
+			led-cur = /bits/ 8 <0x20>;
+			max-cur = /bits/ 8 <0x60>;
+			reg = <2>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <64>;
+	};
+
+	touchscreen: touchscreen@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		reg = <0x5c>;
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		status = "disabled";
+	};
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1341";
+		reg = <0x68>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "disabled";
+
+	oled_1309: oled@3c {
+		compatible = "solomon,ssd1309fb-i2c";
+		reg = <0x3c>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,segment-no-remap;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	oled_1305: oled@3d {
+		compatible = "solomon,ssd1305fb-i2c";
+		reg = <0x3d>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,col-offset = <4>;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_oled: gpio@41 {
+		compatible = "nxp,pca9536";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x41>;
+		vcc-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	touchkeys: keys@5a {
+		compatible = "fsl,mpr121-touchkey";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchkeys>;
+		reg = <0x5a>;
+		vdd-supply = <&sw2_reg>;
+		autorepeat;
+		linux,keycodes = <KEY_1>, <KEY_2>, <KEY_3>, <KEY_4>, <KEY_5>,
+				<KEY_6>, <KEY_7>, <KEY_8>, <KEY_9>,
+				<KEY_BACKSPACE>, <KEY_0>, <KEY_ENTER>;
+		poll-interval = <50>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b020
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b020
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b020
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b020
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b020
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b020
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b020
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b020
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b020
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b020
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b020
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b020
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b020
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b010
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b010
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b098
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07                  0x1b0b0
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b098
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x8
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b098
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b098
+		>;
+	};
+
+	pinctrl_touchkeys: touchkeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b098
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x1b098
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0a8
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0a8
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__UART2_TX_DATA	0x1b098
+			MX6QDL_PAD_GPIO_8__UART2_RX_DATA	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__USB_H1_OC	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b098
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b098
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotg-vbus {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD	0x1f069
+			MX6QDL_PAD_SD4_CLK__SD4_CLK	0x10069
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0	0x17069
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1	0x17069
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2	0x17069
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3	0x17069
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4	0x17069
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5	0x17069
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6	0x17069
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7	0x17069
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B	0x1b0b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "disabled";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	over-current-active-low;
+	status = "disabled";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	over-current-active-low;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+	status = "okay";
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <109>;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	vmmc-supply = <&sw2_reg>;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-prtwd2.dts b/arch/arm/boot/dts/imx6q-prtwd2.dts
index 349959d38020..54a57a4548e2 100644
--- a/arch/arm/boot/dts/imx6q-prtwd2.dts
+++ b/arch/arm/boot/dts/imx6q-prtwd2.dts
@@ -22,6 +22,13 @@
 		reg = <0x80000000 0x20000000>;
 	};
 
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
 	usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
@@ -49,13 +56,17 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>;
-	clock-names = "ipg", "ahb";
 	status = "okay";
 
 	fixed-link {
diff --git a/arch/arm/boot/dts/imx6q-yapp4-pegasus.dts b/arch/arm/boot/dts/imx6q-yapp4-pegasus.dts
new file mode 100644
index 000000000000..ec6651ba4ba2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-yapp4-pegasus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Pegasus i.MX6Quad board";
+	compatible = "ysoft,imx6q-yapp4-pegasus", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi b/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
index 3def1b621c8e..2731faede1cb 100644
--- a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
@@ -105,6 +105,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_3v3: regulator-3v3 {
@@ -232,13 +233,16 @@
 	};
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-mode = "rmii";
 	phy-supply = <&reg_3v3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 41e08fa23cce..b72ec745f6d1 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -1049,8 +1049,8 @@
 				clocks = <&clks IMX6QDL_CLK_ENET>,
 					 <&clks IMX6QDL_CLK_ENET>,
 					 <&clks IMX6QDL_CLK_ENET_REF>,
-					 <&clks IMX6QDL_CLK_ENET_REF>;
-				clock-names = "ipg", "ahb", "ptp", "enet_out";
+					 <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+				clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
 				fsl,stop-mode = <&gpr 0x34 27>;
 				nvmem-cells = <&fec_mac_addr>;
 				nvmem-cell-names = "mac-address";
diff --git a/arch/arm/boot/dts/imx6qp-yapp4-pegasus-plus.dts b/arch/arm/boot/dts/imx6qp-yapp4-pegasus-plus.dts
new file mode 100644
index 000000000000..4a961a33bf2d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qp-yapp4-pegasus-plus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Pegasus+ i.MX6QuadPlus board";
+	compatible = "ysoft,imx6qp-yapp4-pegasus-plus", "fsl,imx6qp";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6sl-tolino-vision.dts b/arch/arm/boot/dts/imx6sl-tolino-vision.dts
new file mode 100644
index 000000000000..2694fe18a91b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sl-tolino-vision.dts
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Tolino Vison ebook reader
+ *
+ * Name on mainboard is: 37NB-E60Q30+4A3
+ * Serials start with: 6032
+ *
+ * Copyright 2023 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Tolino Vision";
+	compatible = "kobo,tolino-vision", "fsl,imx6sl";
+
+	aliases {
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ec 0 50000>;
+		power-supply = <&backlight_regulator>;
+	};
+
+	backlight_regulator: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_power>;
+		regulator-name = "backlight";
+		gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			/* magnetic sensor in the corner next to the uSD slot */
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-fl {
+			label = "Frontlight";
+			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BRIGHTNESS_CYCLE>;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			/* LED on home button */
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* LED on power button */
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	touchscreen@15 {
+		compatible = "elan,ektf2132";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ts>;
+		power-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&gpio5 6 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	accelerometer@1d {
+		compatible = "fsl,mma8652";
+		reg = <0x1d>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	ec: embedded-controller@43 {
+		compatible = "netronix,ntxec";
+		reg = <0x43>;
+		#pwm-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ec>;
+		interrupts-extended = <&gpio5 11 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+	};
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* J9 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	cd-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	/* removable uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/* CyberTan WC121 (BCM43362) SDIO WiFi */
+};
+
+&usdhc4 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc4_sleep>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	status = "okay";
+
+	/* internal eMMC */
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_backlight_power: backlight-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059
+		>;
+	};
+
+	pinctrl_ec: ecgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11  0x17000
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x110B0
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x110B0
+			MX6SL_PAD_KEY_COL1__GPIO3_IO26  0x11030
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT6__GPIO5_IO07    0x17059
+			MX6SL_PAD_SD1_DAT7__GPIO5_IO10    0x17059
+			MX6SL_PAD_EPDC_SDCE2__GPIO1_IO29  0x17059
+		>;
+	};
+
+	pinctrl_ts: tsgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13	0x110B0
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06	0x1B0B1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6SL_PAD_SD2_DAT4__GPIO5_IO02		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x17059
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x13059
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x17059
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x17059
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x17059
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x17059
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x17059
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x17059
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x17059
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x17059
+			MX6SL_PAD_FEC_REF_CLK__SD4_RESET	0x17068
+		>;
+	};
+
+	pinctrl_usdhc4_100mhz: usdhc4-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x170b9
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x130b9
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x170b9
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x170b9
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x170b9
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x170b9
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x170b9
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x170b9
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x170b9
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc4_200mhz: usdhc4-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x170f9
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x130f9
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x170f9
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x170f9
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x170f9
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x170f9
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x170f9
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x170f9
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x170f9
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc4_sleep: usdhc4-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__GPIO4_IO21	0x100c1
+			MX6SL_PAD_FEC_MDIO__GPIO4_IO20		0x100c1
+			MX6SL_PAD_FEC_RX_ER__GPIO4_IO19		0x100c1
+			MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25	0x100c1
+			MX6SL_PAD_FEC_RXD1__GPIO4_IO18		0x100c1
+			MX6SL_PAD_FEC_TXD0__GPIO4_IO24		0x100c1
+			MX6SL_PAD_FEC_MDC__GPIO4_IO23		0x100c1
+			MX6SL_PAD_FEC_RXD0__GPIO4_IO17		0x100c1
+			MX6SL_PAD_FEC_TX_EN__GPIO4_IO22		0x100c1
+			MX6SL_PAD_FEC_TXD1__GPIO4_IO16		0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-prti6g.dts b/arch/arm/boot/dts/imx6ul-prti6g.dts
index c18390f238e1..b7c96fbe7a91 100644
--- a/arch/arm/boot/dts/imx6ul-prti6g.dts
+++ b/arch/arm/boot/dts/imx6ul-prti6g.dts
@@ -26,6 +26,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet1_ref_pad";
 	};
 
 	leds {
@@ -60,6 +61,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>, <&clock_ksz8081_out>;
+	clock-names = "ckil", "osc", "ipp_di0", "ipp_di1", "enet1_ref_pad";
+	assigned-clocks = <&clks IMX6UL_CLK_ENET1_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081_out>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -85,12 +93,6 @@
 	pinctrl-0 = <&pinctrl_eth1>;
 	phy-mode = "rmii";
 	phy-handle = <&rmii_phy>;
-	clocks = <&clks IMX6UL_CLK_ENET>,
-		 <&clks IMX6UL_CLK_ENET_AHB>,
-		 <&clks IMX6UL_CLK_ENET_PTP>,
-		 <&clock_ksz8081_out>;
-	clock-names = "ipg", "ahb", "ptp",
-		      "enet_clk_ref";
 	status = "okay";
 
 	mdio {
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index f0a9139748b8..3d9d0f823568 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -531,10 +531,9 @@
 				clocks = <&clks IMX6UL_CLK_ENET>,
 					 <&clks IMX6UL_CLK_ENET_AHB>,
 					 <&clks IMX6UL_CLK_ENET_PTP>,
-					 <&clks IMX6UL_CLK_ENET2_REF_125M>,
-					 <&clks IMX6UL_CLK_ENET2_REF_125M>;
+					 <&clks IMX6UL_CLK_ENET2_REF_SEL>;
 				clock-names = "ipg", "ahb", "ptp",
-					      "enet_clk_ref", "enet_out";
+					      "enet_clk_ref";
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
 				fsl,stop-mode = <&gpr 0x10 4>;
@@ -879,10 +878,9 @@
 				clocks = <&clks IMX6UL_CLK_ENET>,
 					 <&clks IMX6UL_CLK_ENET_AHB>,
 					 <&clks IMX6UL_CLK_ENET_PTP>,
-					 <&clks IMX6UL_CLK_ENET_REF>,
-					 <&clks IMX6UL_CLK_ENET_REF>;
+					 <&clks IMX6UL_CLK_ENET1_REF_SEL>;
 				clock-names = "ipg", "ahb", "ptp",
-					      "enet_clk_ref", "enet_out";
+					      "enet_clk_ref";
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
 				fsl,stop-mode = <&gpr 0x10 3>;
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-common.dtsi b/arch/arm/boot/dts/imx6ull-tarragon-common.dtsi
new file mode 100644
index 000000000000..3fdece5bd31f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-common.dtsi
@@ -0,0 +1,852 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx6ull.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &usdhc2; /* eMMC */
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-0 = <&pinctrl_emmc_rst>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_dcdc_3v3: regulator-dcdc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "dcdc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_status_leds>;
+
+		led-1 {
+			function = LED_FUNCTION_BOOT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_PROGRAMMING;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_motor
+		     &pinctrl_adc_cp
+		     &pinctrl_adc_pp>;
+	vref-supply = <&vgen1_reg>;
+	status = "okay";
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <3>;
+	cs-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH
+		    &gpio3 2  GPIO_ACTIVE_HIGH
+		    &gpio3 4  GPIO_ACTIVE_HIGH>;
+};
+
+&ecspi4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	num-cs = <1>;
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1
+		     &pinctrl_enet1_phy_rst
+		     &pinctrl_enet_mdio>;
+	phy-supply = <&reg_dcdc_3v3>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet1_phy_int>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&gpio2 7 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+			max-speed = <100>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "CP_INVERT",
+			  "",
+			  "",				/* 15 */
+			  "",
+			  "",
+			  "",
+			  "MOTOR_1_FAULT_N",
+			  "",				/* 20 */
+			  "",
+			  "ROTARY_SWITCH_1_2_N",
+			  "ROTARY_SWITCH_1_4_N",
+			  "ROTARY_SWITCH_1_8_N",
+			  "MOTOR_2_FAULT_N";		/* 25 */
+};
+
+&gpio3 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "EXT_GPIO",
+			  "MOTOR_1_DRIVER_IN1_N",
+			  "MOTOR_1_DRIVER_IN2",
+			  "MOTOR_2_DRIVER_IN1",
+			  "STM32_BOOT0",		/* 10 */
+			  "STM32_RST_N",
+			  "RELAY_1_ENABLE",
+			  "RELAY_2_ENABLE",
+			  "",
+			  "",				/* 15 */
+			  "QCA700X_MAINS_BOOTLOADER_N",
+			  "QCA700X_CP_RST_N",
+			  "QCA700X_CP_BOOTLOADER_N",
+			  "",
+			  "DIGITAL_OUT_1",		/* 20 */
+			  "DIGITAL_OUT_2",
+			  "DIGITAL_OUT_3",
+			  "DIGITAL_OUT_4",
+			  "DIGITAL_OUT_5",
+			  "DIGITAL_OUT_6",		/* 25 */
+			  "ROTARY_SWITCH_2_8_N",
+			  "ROTARY_SWITCH_2_4_N",
+			  "ROTARY_SWITCH_2_2_N";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "BOARD_VARIANT_1",
+			  "BOARD_VARIANT_2",
+			  "BOARD_VARIANT_0",		/* 15 */
+			  "BOARD_VARIANT_3",
+			  "",
+			  "ROTARY_SWITCH_2_1_N",
+			  "",
+			  "DIGITAL_IN_5",		/* 20 */
+			  "",
+			  "",
+			  "DIGITAL_IN_6",
+			  "",
+			  "DIGITAL_IN_1",		/* 25 */
+			  "DIGITAL_IN_2",
+			  "DIGITAL_IN_4",
+			  "DIGITAL_IN_3";
+
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <19 0>;
+		input;
+	};
+};
+
+&gpio5 {
+	gpio-line-names = "ROTARY_SWITCH_1_1_N",	/* 0 */
+			  "",
+			  "RELAY_2_SENSE",
+			  "RELAY_1_SENSE",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "QCA700X_MAINS_RST_N",
+			  "MOTOR_2_DRIVER_IN2",
+			  "",
+			  "CP_POSITIVE_PEAK_RST",	/* 10 */
+			  "CP_NEGATIVE_PEAK_RST";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3001: pmic@8 {
+		compatible = "fsl,pfuze3001";
+		reg = <0x08>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-name = "SW1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "SW2";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-name = "SW3";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-name = "VSNVS";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-name = "VLDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-name = "VLDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-name = "VCCSD";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-name = "V33";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-name = "VLDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-name = "VLDO4";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	onewire@18 {
+		compatible = "maxim,ds2484";
+		reg = <0x18>;
+	};
+
+	accelerometer@19 {
+		compatible = "st,iis328dq", "st,h3lis331dl-accel";
+		reg = <0x19>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accelerometer_int1_snvs>;
+		vdd-supply = <&reg_dcdc_3v3>;
+		vddio-supply = <&reg_dcdc_3v3>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <5 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_board_var
+		     &pinctrl_digital_input
+		     &pinctrl_digital_output
+		     &pinctrl_gpio_motor
+		     &pinctrl_hog_pins
+		     &pinctrl_rotary_switch1
+		     &pinctrl_rotary_switch2>;
+
+	pinctrl_adc_cp: adc-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02            0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03            0xb0
+		>;
+	};
+
+	pinctrl_adc_motor: adc-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00            0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01            0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04            0xb0
+		>;
+	};
+
+	pinctrl_adc_pp: adc-ppgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05            0xb0
+		>;
+	};
+
+	pinctrl_board_var: board-vargrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__GPIO4_IO15              0xb0
+			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13            0xb0
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14            0xb0
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16              0xb0
+		>;
+	};
+
+	pinctrl_digital_input: digital-inputgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25            0xb0
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26            0xb0
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28            0xb0
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27            0xb0
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20             0xb0
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23            0xb0
+		>;
+	};
+
+	pinctrl_digital_output: digital-outputgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA15__GPIO3_IO20            0x400000b0
+			MX6UL_PAD_LCD_DATA16__GPIO3_IO21            0x400000b0
+			MX6UL_PAD_LCD_DATA17__GPIO3_IO22            0x400000b0
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23            0x400000b0
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24            0x400000b0
+			MX6UL_PAD_LCD_DATA20__GPIO3_IO25            0x400000b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29         0x10b0
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02             0xb0
+			MX6UL_PAD_LCD_RESET__GPIO3_IO04             0xb0
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK        0x10b0
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO        0x10b0
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI        0x10b0
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15           0x10b0
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK       0x10b0
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO         0x10b0
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI          0x10b0
+		>;
+	};
+
+	pinctrl_emmc_rst: emmc-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10              0x400010b0
+		>;
+	};
+
+	pinctrl_enet_mdio: enet-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO            0x10b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC             0x10b0
+		>;
+	};
+
+	pinctrl_enet1_phy_int: enet1-phy-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07           0x10b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00     0x100b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01     0x100b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN          0x100b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1      0x400000b1
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00     0xb0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01     0xb0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN          0xb0
+		>;
+	};
+
+	pinctrl_ext_uart: ext-uartgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_DATA0__UART7_DCE_RX      0xb0
+			MX6UL_PAD_ENET2_RX_EN__UART7_DCE_TX         0xb0
+		>;
+	};
+
+	pinctrl_fan_enable: fan-enablegrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05            0x400000b0
+		>;
+	};
+
+	pinctrl_gpio_motor: gpio-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07            0x400000b0
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08            0x400000b0
+			MX6UL_PAD_LCD_DATA04__GPIO3_IO09            0x400000b0
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19           0xb0
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25         0xb0
+		>;
+	};
+
+	pinctrl_hog_pins: hog-pinsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA07__GPIO3_IO12            0x400000b0
+			MX6UL_PAD_LCD_DATA08__GPIO3_IO13            0x400000b0
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13              0x400070a0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10            0x400000b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11            0x400000b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA           0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL           0x400008b0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21         0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20         0x400008b0
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__USDHC2_VSELECT        0x70b1
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19             0xb0
+		>;
+	};
+
+	pinctrl_pwm_cp: pinctrl-pwm-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT             0x60a0
+		>;
+	};
+
+	pinctrl_pwm_digital_input_ref: pwm-digital-input-refgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT              0xb0
+		>;
+	};
+
+	pinctrl_pwm_fan: pwm-fangrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT                0x60a0
+		>;
+	};
+
+	pinctrl_qca700x_cp_btld: qca700x-cp-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA13__GPIO3_IO18            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_int: qca700x-cp-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_DATA1__GPIO2_IO19             0x10b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_rst: qca700x-cp-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_mains_btld: qca700x-mains-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA11__GPIO3_IO16            0x400000b0
+		>;
+	};
+
+	pinctrl_rotary_switch1: rotary-switch1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22           0xb0
+			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23           0xb0
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24         0xb0
+		>;
+	};
+
+	pinctrl_rotary_switch2: rotary-switch2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18            0xb0
+			MX6UL_PAD_LCD_DATA23__GPIO3_IO28            0xb0
+			MX6UL_PAD_LCD_DATA22__GPIO3_IO27            0xb0
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26            0xb0
+		>;
+	};
+
+	pinctrl_rs485_1: rs485-1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18           0xb0
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX       0xb0
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX       0xb0
+		>;
+	};
+
+	pinctrl_rs485_2: rs485-2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24            0x10b0
+			MX6UL_PAD_CSI_DATA01__UART5_DCE_RX          0x10b0
+			MX6UL_PAD_CSI_DATA00__UART5_DCE_TX          0x10b0
+		>;
+	};
+
+	pinctrl_status_leds: status-ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA09__GPIO3_IO14            0xb0
+			MX6UL_PAD_LCD_DATA10__GPIO3_IO15            0xb0
+			MX6UL_PAD_LCD_DATA14__GPIO3_IO19            0xb0
+		>;
+	};
+
+	pinctrl_stm32: stm32grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA1__UART6_DCE_RX      0x10b0
+			MX6UL_PAD_ENET2_RX_DATA0__UART6_DCE_TX      0x10b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DTE_RX             0xb0
+			MX6UL_PAD_LCD_ENABLE__UART4_DTE_TX          0xb0
+		>;
+	};
+
+	pinctrl_usb: usbgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USB_OTG1_OC              0x70b0
+			MX6UL_PAD_SD1_DATA0__ANATOP_OTG1_ID         0x70b0
+		>;
+	};
+
+	pinctrl_usb_pwr: usb-pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USB_OTG1_PWR             0xb0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x7071
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x7071
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x7071
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x7071
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x7071
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x7071
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x7071
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x7071
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x7071
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x7071
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70b1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70b1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70b1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70b1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70b1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70b1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70b1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70b1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70b1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70b1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70f1
+		>;
+	};
+
+	pinctrl_wdog2: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_VSYNC__WDOG2_WDOG_B           0x10b0
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default_snvs";
+	pinctrl-0 = <&pinctrl_cp_peak_snvs
+		     &pinctrl_gpio_motor_snvs
+		     &pinctrl_relay_sense_snvs
+		     &pinctrl_rotary_switch1_snvs>;
+
+	pinctrl_accelerometer_int1_snvs: accelerometer-int1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05         0x130a0
+		>;
+	};
+
+	pinctrl_cp_peak_snvs: cp-peak-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10           0x130a0
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11           0x130a0
+		>;
+	};
+
+	pinctrl_enet1_phy_rst: enet1-phy-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06         0x100a0
+		>;
+	};
+
+	pinctrl_fan_sense_snvs: fan-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01         0x100a0
+		>;
+	};
+
+	pinctrl_gpio_motor_snvs: gpio-motor-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08         0x110a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_int: qca700x-mains-intgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09         0x130a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_rst: qca700x-mains-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07         0x400100a0
+		>;
+	};
+
+	pinctrl_relay_sense_snvs: relay-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03         0x100a0
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02         0x100a0
+		>;
+	};
+
+	pinctrl_rotary_switch1_snvs: rotary-switch1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00         0x110a0
+		>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_digital_input_ref>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_cp>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	fsl,dte-mode;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_2>;
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_stm32>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ext_uart>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb
+		     &pinctrl_usb_pwr>;
+	dr_mode = "host";
+	power-active-high;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usbphy2 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&sw2_reg>;
+	vqmmc-supply = <&reg_1v8>;
+	mmc-pwrseq = <&emmc_pwrseq>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog2>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-master.dts b/arch/arm/boot/dts/imx6ull-tarragon-master.dts
new file mode 100644
index 000000000000..67007ce383e3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-master.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Master";
+	compatible = "chargebyte,imx6ull-tarragon-master", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&ecspi4 {
+	status = "okay";
+
+	qca700x_mains: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_mains_int
+			     &pinctrl_qca700x_mains_rst
+			     &pinctrl_qca700x_mains_btld>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-micro.dts b/arch/arm/boot/dts/imx6ull-tarragon-micro.dts
new file mode 100644
index 000000000000..e471c2005bee
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-micro.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Micro";
+	compatible = "chargebyte,imx6ull-tarragon-micro", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-slave.dts b/arch/arm/boot/dts/imx6ull-tarragon-slave.dts
new file mode 100644
index 000000000000..cee223b5f8e1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-slave.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Slave";
+	compatible = "chargebyte,imx6ull-tarragon-slave", "fsl,imx6ull";
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-slavext.dts b/arch/arm/boot/dts/imx6ull-tarragon-slavext.dts
new file mode 100644
index 000000000000..7fd53b7a4372
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-slavext.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon SlaveXT";
+	compatible = "chargebyte,imx6ull-tarragon-slavext", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/imx7d-remarkable2.dts
index 8b2f11e85e05..dc954e4f63e0 100644
--- a/arch/arm/boot/dts/imx7d-remarkable2.dts
+++ b/arch/arm/boot/dts/imx7d-remarkable2.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "imx7d.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
 
 / {
 	model = "reMarkable 2.0";
@@ -69,6 +70,17 @@
 		startup-delay-us = <100000>; /* 100 ms */
 	};
 
+	reg_touch: regulator-touch {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3_TOUCH";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_reg>;
+		gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
@@ -79,6 +91,10 @@
 	};
 };
 
+&cpu0 {
+	cpu-supply = <&buck1>;
+};
+
 &clks {
 	assigned-clocks = <&clks IMX7D_CLKO2_ROOT_SRC>,
 			  <&clks IMX7D_CLKO2_ROOT_DIV>;
@@ -106,6 +122,193 @@
 	};
 };
 
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	bd71815: pmic@4b {
+		compatible = "rohm,bd71815";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bd71815>;
+		interrupt-parent = <&gpio6>; /* PMIC_INT_B GPIO6_IO16 */
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		gpio-controller;
+		clocks = <&clks IMX7D_CLKO2_ROOT_SRC>;
+		clock-output-names = "bd71815-32k-out";
+		#clock-cells = <0>;
+		#gpio-cells = <2>;
+
+		regulators {
+			buck1: buck1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2: buck2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3: buck3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <2700000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: buck4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: ldo1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: ldo2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: ldo3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: ldo4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: ldo5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6: ldodvref {
+				regulator-name = "ldodvref";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo7: ldolpsr {
+				regulator-name = "ldolpsr";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			boost: wled {
+				regulator-name = "wled";
+				regulator-min-microamp = <10>;
+				regulator-max-microamp = <25000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_touch>;
+		touchscreen-size-x = <880>;
+		touchscreen-size-y = <1280>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@0 {
+			reg = <0>;
+			linux,keycodes = <KEY_HOMEPAGE>;
+		};
+
+		button@1 {
+			reg = <1>;
+			linux,keycodes = <KEY_MENU>;
+		};
+
+		button@2 {
+			reg = <2>;
+			linux,keycodes = <KEY_BACK>;
+		};
+
+		button@3 {
+			reg = <3>;
+			linux,keycodes = <KEY_SEARCH>;
+		};
+
+		button@4 {
+			reg = <4>;
+			linux,keycodes = <KEY_VOLUMEDOWN>;
+		};
+
+		button@5 {
+			reg = <5>;
+			linux,keycodes = <KEY_VOLUMEUP>;
+		};
+
+		button@6 {
+			reg = <6>;
+			linux,keycodes = <KEY_CAMERA>;
+		};
+
+		button@7 {
+			reg = <7>;
+			linux,keycodes = <KEY_POWER>;
+		};
+	};
+};
+
 &i2c4 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "sleep";
@@ -218,6 +421,12 @@
 };
 
 &iomuxc {
+	pinctrl_bd71815: bd71815grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x59
+		>;
+	};
+
 	pinctrl_brcm_reg: brcmreggrp {
 		fsl,pins = <
 			/* WIFI_PWR_EN */
@@ -232,6 +441,15 @@
 		>;
 	};
 
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			/* CYTTSP interrupt */
+			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x54
+			/* CYTTSP reset */
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13		0x04
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
@@ -239,6 +457,20 @@
 		>;
 	};
 
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x4000007f
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX7D_PAD_I2C3_SDA__I2C3_SDA		0x4000007f
+			MX7D_PAD_I2C3_SCL__I2C3_SCL		0x4000007f
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX7D_PAD_I2C4_SDA__I2C4_SDA		0x4000007f
@@ -246,6 +478,13 @@
 		>;
 	};
 
+	pinctrl_touch_reg: touchreggrp {
+		fsl,pins = <
+			/* TOUCH_PWR_EN */
+			MX7D_PAD_GPIO1_IO11__GPIO1_IO11		0x14
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index 7ceb7c09f7ad..4b94b8afb55d 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -165,6 +165,15 @@
 		  reg = <0x306d0000 0x10000>;
 		  status = "disabled";
 	};
+
+	pxp: pxp@30700000 {
+		compatible = "fsl,imx7d-pxp";
+		reg = <0x30700000 0x10000>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX7D_PXP_CLK>;
+		clock-names = "axi";
+	};
 };
 
 &aips3 {