Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 382 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts b/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts
new file mode 100644
index 000000000000..3fe4591e21f5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts
@@ -0,0 +1,382 @@
+/*
+ * Copyright (C) 2015 Lucas Stach <kernel@pengutronix.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sr-som.dtsi"
+#include "imx6qdl-sr-som-brcm.dtsi"
+
+/ {
+	model = "Auvidea H100";
+	compatible = "auvidea,h100", "fsl,imx6q";
+
+	/* Will be filled by the bootloader */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	hdmi_osc: hdmi-osc {
+		compatible = "fixed-clock";
+		clock-output-names = "hdmi-osc";
+		clock-frequency = <27000000>;
+		#clock-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_h100_leds>;
+
+		led0: led-power {
+			label = "power";
+			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led1: led-stream {
+			label = "stream";
+			gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2: led-rec {
+			label = "rec";
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_hdmi: regulator-hdmi {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_h100_reg_hdmi>;
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+		regulator-name = "V_HDMI";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_usbh1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_h100_usbh1_vbus>;
+		regulator-name = "USB_H1_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbotg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_h100_usbotg_vbus>;
+		regulator-name = "USB_OTG_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	sound-sgtl5000 {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "H100 on-board codec";
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-ext-port = <5>;
+		mux-int-port = <1>;
+		ssi-controller = <&ssi1>;
+	};
+};
+
+&audmux {
+	status = "okay";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_h100_hdmi>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_h100_i2c1>;
+	status = "okay";
+
+	eeprom: eeprom@51 {
+		compatible = "microchip,24c02", "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	rtc: pcf8523@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+
+	sgtl5000: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_h100_sgtl5000>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	tc358743: tc358743@f {
+		compatible = "toshiba,tc358743";
+		reg = <0x0f>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_h100_tc358743>;
+		clocks = <&hdmi_osc>;
+		clock-names = "refclk";
+		reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+		/* IRQ has a wrong pull resistor which renders it useless  */
+
+		port {
+			tc358743_out: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				data-lanes = <1 2 3 4>;
+				clock-lanes = <0>;
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <297000000>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_h100_i2c2>;
+	status = "okay";
+};
+
+&iomuxc {
+	h100 {
+		pinctrl_h100_hdmi: h100-hdmi {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+			>;
+		};
+
+		pinctrl_h100_i2c1: h100-i2c1 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_h100_i2c2: h100-i2c2 {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_h100_leds: pinctrl-h100-leds {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0x1b0b0
+				MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0
+				MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_reg_hdmi: h100-reg-hdmi {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_sgtl5000: h100-sgtl5000 {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
+				MX6QDL_PAD_KEY_COL0__AUD5_TXC		0x130b0
+				MX6QDL_PAD_KEY_ROW0__AUD5_TXD		0x110b0
+				MX6QDL_PAD_KEY_COL1__AUD5_TXFS		0x130b0
+				MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
+			>;
+		};
+
+		pinctrl_h100_tc358743: h100-tc358743 {
+			fsl,pins = <
+				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_uart2: h100-uart2 {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_h100_usbh1_vbus: hummingboard-usbh1-vbus {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_usbotg_id: hummingboard-usbotg-id {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x13059
+			>;
+		};
+
+		pinctrl_h100_usbotg_vbus: hummingboard-usbotg-vbus {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_usdhc2: h100-usdhc2 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x13059
+				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_usdhc2_100mhz: h100-usdhc2-100mhz {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100b9
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
+			>;
+		};
+
+		pinctrl_h100_usdhc2_200mhz: h100-usdhc2-200mhz {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
+			>;
+		};
+	};
+};
+
+&mipi_csi {
+	status = "okay";
+
+	port {
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&tc358743_out>;
+			data-lanes = <1 2 3 4>;
+			clock-lanes = <0>;
+			clock-noncontinuous;
+			link-frequencies = /bits/ 64 <297000000>;
+		};
+	};
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_h100_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_h100_usbotg_id>;
+	vbus-supply = <&reg_usbotg_vbus>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_h100_usdhc2>;
+	pinctrl-1 = <&pinctrl_h100_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_h100_usdhc2_200mhz>;
+	vmmc-supply = <&reg_3p3v>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};