ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
  been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
  company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 405 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi
new file mode 100644
index 000000000000..147c99191dc2
--- /dev/null
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "pxa3xx.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	/* Will be overridden by bootloader */
+	hw-revision = <0>;
+
+	chosen {
+		bootargs = "root=ubi0:RootFS rootfstype=ubifs rw ubi.mtd=3";
+		stdout-path = &ffuart;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0xa0000000 0x8000000>;	/* 128 MB */
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3-fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8-fixed-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_va_5v0: regulator-va-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "va-5v0-fixed-supply";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio 124 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	ssp_dai0: ssp-dai0 {
+		compatible = "mrvl,pxa-ssp-dai";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ssp0_dai_pins>;
+		port = <&ssp1>;
+		#sound-dai-cells = <0>;
+		dmas = <&pdma 13 3
+			&pdma 14 3>;
+		dma-names = "rx", "tx";
+		clock-names = "extclk";
+	};
+
+	ssp_dai1: ssp-dai1 {
+		compatible = "mrvl,pxa-ssp-dai";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ssp1_dai_pins>;
+		port = <&ssp2>;
+		#sound-dai-cells = <0>;
+		dmas = <&pdma 15 3
+			&pdma 16 3>;
+		dma-names = "rx", "tx";
+		clock-names = "extclk";
+	};
+
+	spi: spi {
+		compatible = "spi-gpio";
+		#address-cells = <0x1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_pins>;
+		gpio-sck = <&gpio 95 GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio 98 GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio 97 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <
+			&gpio 34 GPIO_ACTIVE_HIGH
+			&gpio 125 GPIO_ACTIVE_HIGH
+			&gpio 96 GPIO_ACTIVE_HIGH
+		>;
+		num-chipselects = <3>;
+
+		dac: dac@2 {
+			compatible = "ti,dac7512";
+			reg = <2>;
+			spi-max-frequency = <1000000>;
+			vcc-supply = <&reg_3v3>;
+		};
+	};
+
+	keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		on-off {
+			label = "on_off button";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_F6>;
+		};
+
+		rescue-boot {
+			label = "rescue boot button";
+			gpios = <&gpio 115 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_F4>;
+		};
+
+		setup {
+			label = "setup";
+			gpios = <&gpio 119 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_F3>;
+		};
+	};
+
+	rotary: rotary-encoder {
+		compatible = "rotary-encoder";
+		gpios = <
+			&gpio 19 GPIO_ACTIVE_LOW
+			&gpio 20 GPIO_ACTIVE_HIGH
+		>;
+		linux,axis = <REL_X>;
+		rotary-encoder,relative-axis;
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_a &led_pins_b>;
+
+		left {
+			label = "raumfeld:1";
+			gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
+		};
+
+		right {
+			label = "raumfeld:2";
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-names = "default";
+		pinctrl-0 = <&poweroff_pins>;
+		gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	};
+
+	mmc0_pwrseq: mmc-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mmc0_pwrseq_pins>;
+		reset-gpios = <
+			&gpio 113 GPIO_ACTIVE_LOW	/* W2W_RESET	*/
+			&gpio 114 GPIO_ACTIVE_LOW	/* W2W_PDN	*/
+		>;
+	};
+
+	ethernet: ethernet@10000000 {
+		compatible = "smsc,lan9115";
+		pinctrl-names = "default";
+		pinctrl-0 = <&smsc_pins &smsc_bus_pins>;
+		reg = <0x10000000 0x100000>;
+		phy-mode = "mii";
+		interrupt-parent = <&gpio>;
+		interrupts = <40 IRQ_TYPE_EDGE_FALLING>;
+		vdd33a-supply = <&reg_3v3>;
+		vddvario-supply = <&reg_1v8>;
+		reset-gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+		smsc,irq-push-pull;
+	};
+};
+
+&ffuart {
+	status = "okay";
+};
+
+&pwri2c {
+	status = "okay";
+
+	max8660: regulator@34 {
+		compatible = "maxim,max8660";
+		reg = <0x34>;
+
+		regulators {
+			regulator-v3 {
+				regulator-compatible = "V3(DCDC)";
+				regulator-min-microvolt = <725000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			regulator-v4 {
+				regulator-compatible = "V4(DCDC)";
+				regulator-min-microvolt = <725000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			regulator-v5 {
+				regulator-compatible = "V5(LDO)";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <2000000>;
+			};
+
+			reg_vcc_sdio: regulator-v6 {
+				regulator-compatible = "V6(LDO)";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			regulator-v7 {
+				regulator-compatible = "V7(LDO)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+};
+
+&pxai2c1 {
+	status = "okay";
+	mrvl,i2c-fast-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pxai2c1_pins>;
+};
+
+&ssp1 {
+	status = "okay";
+};
+
+&ssp2 {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		nand-rb = <0>;
+		nand-ecc-mode = "hw";
+		marvell,nand-keep-config;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Bootloader";
+				reg = <0x0000000 0xa0000>;
+				read-only;
+			};
+
+			partition@a0000 {
+				label = "BootloaderEnvironment";
+				reg = <0x0a0000 0x20000>;
+			};
+
+			partition@c0000 {
+				label = "BootloaderSplashScreen";
+				reg = <0x0c0000 0x60000>;
+			};
+
+			partition@120000 {
+				label = "UBI";
+				reg = <0x120000 0x7ee0000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	status = "okay";
+	marvell,enable-port1;
+	marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pxa3xx_ohci_pins>;
+};
+
+&mmc0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	pxa-mmc,detect-delay-ms = <200>;
+	vmmc-supply = <&reg_vcc_sdio>;
+	mmc-pwrseq = <&mmc0_pwrseq>;
+	non-removable;
+	bus-width = <4>;
+};
+
+&pinctrl {
+	poweroff_pins: poweroff-pins {
+		pinctrl-single,pins = <MFP_PIN_PXA300(16) MFP_AF0>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+	};
+
+	led_pins_a: led-pins-a {
+		pinctrl-single,pins = <MFP_PIN_PXA300(35) MFP_AF0>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+	};
+
+	led_pins_b: led-pins-b {
+		pinctrl-single,pins = <MFP_PIN_PXA300(36) MFP_AF0>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_DRIVE_HIGH);
+	};
+
+	pxai2c1_pins: pxai2c1-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(21) MFP_AF1	/* I2C_SCL	*/
+			MFP_PIN_PXA300(22) MFP_AF1	/* I2C_SDA	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH);
+	};
+
+	gpio_keys_pins: gpio-keys-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(14) MFP_AF0	/* on-off	*/
+			MFP_PIN_PXA300(115) MFP_AF0	/* rescue boot	*/
+			MFP_PIN_PXA300(119) MFP_AF0	/* setup	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+	};
+
+	spi_pins: spi-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(95) MFP_AF0	/* SCK		*/
+			MFP_PIN_PXA300(97) MFP_AF0	/* MOSI		*/
+			MFP_PIN_PXA300(98) MFP_AF0	/* MISO		*/
+			MFP_PIN_PXA300(34) MFP_AF0	/* CS#0		*/
+			MFP_PIN_PXA300(125) MFP_AF0	/* CS#1		*/
+			MFP_PIN_PXA300(96) MFP_AF0	/* CS#2		*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+	};
+
+	pxa3xx_ohci_pins: pxa3xx-ohci-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300_2(0) MFP_AF1	/* USBHPEN	*/
+			MFP_PIN_PXA300_2(1) MFP_AF1	/* USBHPWR	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+	};
+
+	smsc_pins: smsc-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(39) MFP_AF0	/* RESET	*/
+			MFP_PIN_PXA300(40) MFP_AF0	/* IRQ		*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+	};
+
+	smsc_bus_pins: smsc-bus-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(1) MFP_AF1	/* nCS2		*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+	};
+
+	mmc0_pins: mmc0-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(3) MFP_AF4	/* MMC1_DAT0	*/
+			MFP_PIN_PXA300(4) MFP_AF4	/* MMC1_DAT1	*/
+			MFP_PIN_PXA300(5) MFP_AF4	/* MMC1_DAT2	*/
+			MFP_PIN_PXA300(6) MFP_AF4	/* MMC1_DAT3	*/
+			MFP_PIN_PXA300(7) MFP_AF4	/* MMC1_CLK	*/
+			MFP_PIN_PXA300(8) MFP_AF4	/* MMC1_CMD	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_DRIVE_HIGH);
+	};
+
+	mmc0_pwrseq_pins: mmc0-pwrseq-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(113) MFP_AF0	/* W2W_RESET	*/
+			MFP_PIN_PXA300(114) MFP_AF0	/* W2W_PDN	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+	};
+
+	ssp0_dai_pins: ssp0-dai-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(85) MFP_AF1	/* SSP1_SCLK	*/
+			MFP_PIN_PXA300(86) MFP_AF1	/* SSP1_FRM	*/
+			MFP_PIN_PXA300(87) MFP_AF1	/* SSP1_TXD	*/
+			MFP_PIN_PXA300(88) MFP_AF1	/* SSP1_RXD	*/
+			MFP_PIN_PXA300(89) MFP_AF1	/* SSP1_EXTCLK	*/
+			MFP_PIN_PXA300(90) MFP_AF1	/* SSP1_SYSCLK	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+	};
+
+	ssp1_dai_pins: ssp1-dai-pins {
+		pinctrl-single,pins = <
+			MFP_PIN_PXA300(25) MFP_AF2	/* SSP2_SCLK	*/
+			MFP_PIN_PXA300(26) MFP_AF2	/* SSP2_FRM	*/
+			MFP_PIN_PXA300(27) MFP_AF2	/* SSP2_TXD	*/
+			MFP_PIN_PXA300(29) MFP_AF2	/* SSP2_EXTCLK	*/
+		>;
+		pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+	};
+};