Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 575 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/hisilicon/hi3620.dtsi b/arch/arm/boot/dts/hisilicon/hi3620.dtsi
new file mode 100644
index 000000000000..a254ec009296
--- /dev/null
+++ b/arch/arm/boot/dts/hisilicon/hi3620.dtsi
@@ -0,0 +1,575 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * HiSilicon Ltd. Hi3620 SoC
+ *
+ * Copyright (C) 2012-2013 HiSilicon Ltd.
+ * Copyright (C) 2012-2013 Linaro Ltd.
+ *
+ * Author: Haojian Zhuang <haojian.zhuang@linaro.org>
+ */
+
+#include <dt-bindings/clock/hi3620-clock.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+	};
+
+	pclk: clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "apb_pclk";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "hisilicon,hi3620-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <2>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <3>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	amba-bus {
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges = <0 0xfc000000 0x2000000>;
+
+		L2: cache-controller {
+			compatible = "arm,pl310-cache";
+			reg = <0x100000 0x100000>;
+			interrupts = <0 15 4>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			/* gic dist base, gic cpu base */
+			reg = <0x1000 0x1000>, <0x100 0x100>;
+		};
+
+		sysctrl: system-controller@802000 {
+			compatible = "hisilicon,sysctrl", "syscon";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x802000 0x1000>;
+			reg = <0x802000 0x1000>;
+
+			smp-offset = <0x31c>;
+			resume-offset = <0x308>;
+			reboot-offset = <0x4>;
+
+			clock: clock@0 {
+				compatible = "hisilicon,hi3620-clock";
+				reg = <0 0x10000>;
+				#clock-cells = <1>;
+			};
+		};
+
+		dual_timer0: dual_timer@800000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x800000 0x1000>;
+			/* timer00 & timer01 */
+			interrupts = <0 0 4>, <0 1 4>;
+			clocks = <&clock HI3620_TIMER0_MUX>,
+				 <&clock HI3620_TIMER1_MUX>,
+				 <&clock HI3620_TIMER0_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
+			status = "disabled";
+		};
+
+		dual_timer1: dual_timer@801000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x801000 0x1000>;
+			/* timer10 & timer11 */
+			interrupts = <0 2 4>, <0 3 4>;
+			clocks = <&clock HI3620_TIMER2_MUX>,
+				 <&clock HI3620_TIMER3_MUX>,
+				 <&clock HI3620_TIMER2_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
+			status = "disabled";
+		};
+
+		dual_timer2: dual_timer@a01000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xa01000 0x1000>;
+			/* timer20 & timer21 */
+			interrupts = <0 4 4>, <0 5 4>;
+			clocks = <&clock HI3620_TIMER4_MUX>,
+				 <&clock HI3620_TIMER5_MUX>,
+				 <&clock HI3620_TIMER4_MUX>;
+			clock-names = "timer0lck", "timer1clk", "apb_pclk";
+			status = "disabled";
+		};
+
+		dual_timer3: dual_timer@a02000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xa02000 0x1000>;
+			/* timer30 & timer31 */
+			interrupts = <0 6 4>, <0 7 4>;
+			clocks = <&clock HI3620_TIMER6_MUX>,
+				 <&clock HI3620_TIMER7_MUX>,
+				 <&clock HI3620_TIMER6_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
+			status = "disabled";
+		};
+
+		dual_timer4: dual_timer@a03000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xa03000 0x1000>;
+			/* timer40 & timer41 */
+			interrupts = <0 96 4>, <0 97 4>;
+			clocks = <&clock HI3620_TIMER8_MUX>,
+				 <&clock HI3620_TIMER9_MUX>,
+				 <&clock HI3620_TIMER8_MUX>;
+			clock-names = "timer0clk", "timer1clk", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer5: timer@600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x600 0x20>;
+			interrupts = <1 13 0xf01>;
+		};
+
+		uart0: serial@b00000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xb00000 0x1000>;
+			interrupts = <0 20 4>;
+			clocks = <&clock HI3620_UARTCLK0>, <&clock HI3620_UARTCLK0>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart1: serial@b01000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xb01000 0x1000>;
+			interrupts = <0 21 4>;
+			clocks = <&clock HI3620_UARTCLK1>, <&clock HI3620_UARTCLK1>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: serial@b02000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xb02000 0x1000>;
+			interrupts = <0 22 4>;
+			clocks = <&clock HI3620_UARTCLK2>, <&clock HI3620_UARTCLK2>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart3: serial@b03000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xb03000 0x1000>;
+			interrupts = <0 23 4>;
+			clocks = <&clock HI3620_UARTCLK3>, <&clock HI3620_UARTCLK3>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart4: serial@b04000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xb04000 0x1000>;
+			interrupts = <0 24 4>;
+			clocks = <&clock HI3620_UARTCLK4>, <&clock HI3620_UARTCLK4>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		gpio0: gpio@806000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x806000 0x1000>;
+			interrupts = <0 64 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 2 0 1 &pmx0 3 0 1 &pmx0 4 0 1
+					&pmx0 5 0 1 &pmx0 6 1 1 &pmx0 7 2 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK0>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio1: gpio@807000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x807000 0x1000>;
+			interrupts = <0 65 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 3 1 &pmx0 1 3 1 &pmx0 2 3 1
+					&pmx0 3 3 1 &pmx0 4 3 1 &pmx0 5 4 1
+					&pmx0 6 5 1 &pmx0 7 6 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK1>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio2: gpio@808000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x808000 0x1000>;
+			interrupts = <0 66 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 7 1 &pmx0 1 8 1 &pmx0 2 9 1
+					&pmx0 3 10 1 &pmx0 4 3 1 &pmx0 5 3 1
+					&pmx0 6 3 1 &pmx0 7 3 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK2>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio3: gpio@809000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x809000 0x1000>;
+			interrupts = <0 67 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 3 1 &pmx0 1 3 1 &pmx0 2 3 1
+					&pmx0 3 3 1 &pmx0 4 11 1 &pmx0 5 11 1
+					&pmx0 6 11 1 &pmx0 7 11 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK3>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio4: gpio@80a000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x80a000 0x1000>;
+			interrupts = <0 68 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 11 1 &pmx0 1 11 1 &pmx0 2 11 1
+					&pmx0 3 11 1 &pmx0 4 12 1 &pmx0 5 12 1
+					&pmx0 6 13 1 &pmx0 7 13 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK4>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio5: gpio@80b000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x80b000 0x1000>;
+			interrupts = <0 69 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 14 1 &pmx0 1 15 1 &pmx0 2 16 1
+					&pmx0 3 16 1 &pmx0 4 16 1 &pmx0 5 16 1
+					&pmx0 6 16 1 &pmx0 7 16 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK5>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio6: gpio@80c000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x80c000 0x1000>;
+			interrupts = <0 70 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 16 1 &pmx0 1 16 1 &pmx0 2 17 1
+					&pmx0 3 17 1 &pmx0 4 18 1 &pmx0 5 18 1
+					&pmx0 6 18 1 &pmx0 7 19 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK6>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio7: gpio@80d000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x80d000 0x1000>;
+			interrupts = <0 71 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 19 1 &pmx0 1 20 1 &pmx0 2 21 1
+					&pmx0 3 22 1 &pmx0 4 23 1 &pmx0 5 24 1
+					&pmx0 6 25 1 &pmx0 7 26 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK7>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio8: gpio@80e000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x80e000 0x1000>;
+			interrupts = <0 72 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 27 1 &pmx0 1 28 1 &pmx0 2 29 1
+					&pmx0 3 30 1 &pmx0 4 31 1 &pmx0 5 32 1
+					&pmx0 6 33 1 &pmx0 7 34 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK8>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio9: gpio@80f000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x80f000 0x1000>;
+			interrupts = <0 73 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 35 1 &pmx0 1 36 1 &pmx0 2 37 1
+					&pmx0 3 38 1 &pmx0 4 39 1 &pmx0 5 40 1
+					&pmx0 6 41 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK9>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio10: gpio@810000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x810000 0x1000>;
+			interrupts = <0 74 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 2 43 1 &pmx0 3 44 1 &pmx0 4 45 1
+					&pmx0 5 45 1 &pmx0 6 46 1 &pmx0 7 46 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK10>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio11: gpio@811000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x811000 0x1000>;
+			interrupts = <0 75 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 47 1 &pmx0 1 47 1 &pmx0 2 47 1
+					&pmx0 3 47 1 &pmx0 4 47 1 &pmx0 5 48 1
+					&pmx0 6 49 1 &pmx0 7 49 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK11>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio12: gpio@812000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x812000 0x1000>;
+			interrupts = <0 76 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 49 1 &pmx0 1 50 1 &pmx0 2 49 1
+					&pmx0 3 49 1 &pmx0 4 51 1 &pmx0 5 51 1
+					&pmx0 6 51 1 &pmx0 7 52 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK12>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio13: gpio@813000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x813000 0x1000>;
+			interrupts = <0 77 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 51 1 &pmx0 1 51 1 &pmx0 2 53 1
+					&pmx0 3 53 1 &pmx0 4 53 1 &pmx0 5 54 1
+					&pmx0 6 55 1 &pmx0 7 56 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK13>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio14: gpio@814000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x814000 0x1000>;
+			interrupts = <0 78 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 57 1 &pmx0 1 97 1 &pmx0 2 97 1
+					&pmx0 3 58 1 &pmx0 4 59 1 &pmx0 5 60 1
+					&pmx0 6 60 1 &pmx0 7 61 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK14>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio15: gpio@815000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x815000 0x1000>;
+			interrupts = <0 79 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 61 1 &pmx0 1 62 1 &pmx0 2 62 1
+					&pmx0 3 63 1 &pmx0 4 63 1 &pmx0 5 64 1
+					&pmx0 6 64 1 &pmx0 7 65 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK15>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio16: gpio@816000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x816000 0x1000>;
+			interrupts = <0 80 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 66 1 &pmx0 1 67 1 &pmx0 2 68 1
+					&pmx0 3 69 1 &pmx0 4 70 1 &pmx0 5 71 1
+					&pmx0 6 72 1 &pmx0 7 73 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK16>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio17: gpio@817000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x817000 0x1000>;
+			interrupts = <0 81 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 74 1 &pmx0 1 75 1 &pmx0 2 76 1
+					&pmx0 3 77 1 &pmx0 4 78 1 &pmx0 5 79 1
+					&pmx0 6 80 1 &pmx0 7 81 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK17>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio18: gpio@818000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x818000 0x1000>;
+			interrupts = <0 82 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 82 1 &pmx0 1 83 1 &pmx0 2 83 1
+					&pmx0 3 84 1 &pmx0 4 84 1 &pmx0 5 85 1
+					&pmx0 6 86 1 &pmx0 7 87 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK18>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio19: gpio@819000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x819000 0x1000>;
+			interrupts = <0 83 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 87 1 &pmx0 1 87 1 &pmx0 2 88 1
+					&pmx0 3 88 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK19>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio20: gpio@81a000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x81a000 0x1000>;
+			interrupts = <0 84 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 0 89 1 &pmx0 1 89 1 &pmx0 2 90 1
+					&pmx0 3 90 1 &pmx0 4 91 1 &pmx0 5 92 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK20>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio21: gpio@81b000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x81b000 0x1000>;
+			interrupts = <0 85 0x4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <	&pmx0 3 94 1 &pmx0 7 96 1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clock HI3620_GPIOCLK21>;
+			clock-names = "apb_pclk";
+		};
+
+		pmx0: pinmux@803000 {
+			compatible = "pinctrl-single";
+			reg = <0x803000 0x188>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pinctrl-cells = <1>;
+			#gpio-range-cells = <3>;
+
+			pinctrl-single,register-width = <32>;
+			pinctrl-single,function-mask = <7>;
+			/* pin base, nr pins & gpio function */
+			pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
+						&range 12 1 0 &range 13 29 1
+						&range 43 1 0 &range 44 49 1
+						&range 94 1 1 &range 96 2 1>;
+
+			range: gpio-range {
+				#pinctrl-single,gpio-range-cells = <3>;
+			};
+		};
+
+		pmx1: pinmux@803800 {
+			compatible = "pinconf-single";
+			reg = <0x803800 0x2dc>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pinctrl-cells = <1>;
+
+			pinctrl-single,register-width = <32>;
+		};
+	};
+};