Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This merge window brings a good size of cleanups on various platforms.
  Among the bigger ones:

   - Removal of Samsung s5pc100 and s5p64xx platforms.  Both of these
     have lacked active support for quite a while, and after asking
     around nobody showed interest in keeping them around.  If needed,
     they could be resurrected in the future but it's more likely that
     we would prefer reintroduction of them as DT and
     multiplatform-enabled platforms instead.

   - OMAP4 controller code register define diet.  They defined a lot of
     registers that were never actually used, etc.

   - Move of some of the Tegra platform code (PMC, APBIO, fuse,
     powergate) to drivers/soc so it can be shared with 64-bit code.
     This also converts them over to traditional driver models where
     possible.

   - Removal of legacy gpio-samsung driver, since the last users have
     been removed (moved to pinctrl)

  Plus a bunch of smaller changes for various platforms that sort of
  dissapear in the diffstat for the above.  clps711x cleanups, shmobile
  header file refactoring/moves for multiplatform friendliness, some
  misc cleanups, etc"

* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
  drivers: CCI: Correct use of ! and &
  video: clcd-versatile: Depend on ARM
  video: fix up versatile CLCD helper move
  MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
  ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
  MAINTAINERS: Remove Kirkwood
  ARM: tegra: Convert PMC to a driver
  soc/tegra: fuse: Set up in early initcall
  ARM: tegra: Always lock the CPU reset vector
  ARM: tegra: Setup CPU hotplug in a pure initcall
  soc/tegra: Implement runtime check for Tegra SoCs
  soc/tegra: fuse: fix dummy functions
  soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
  soc/tegra: Add efuse and apbmisc bindings
  soc/tegra: Add efuse driver for Tegra
  ARM: tegra: move fuse exports to soc/tegra/fuse.h
  ARM: tegra: export apb dma readl/writel
  ARM: tegra: Use a function to get the chip ID
  ARM: tegra: Sort includes alphabetically
  ARM: tegra: Move includes to include/soc/tegra
  ...

1 files changed, 5 insertions, 16 deletions

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 8f90595069a1..b24b5dc720e4 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -617,53 +617,41 @@ choice
 		depends on PLAT_SAMSUNG
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
-		bool "Use S3C UART 0 for low-level debug"
+		bool "Use Samsung S3C UART 0 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
 		  their output to UART 0. The port must have been initialised
 		  by the boot-loader before use.
 
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
 	config DEBUG_S3C_UART1
 		depends on PLAT_SAMSUNG
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
-		bool "Use S3C UART 1 for low-level debug"
+		bool "Use Samsung S3C UART 1 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
 		  their output to UART 1. The port must have been initialised
 		  by the boot-loader before use.
 
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
 	config DEBUG_S3C_UART2
 		depends on PLAT_SAMSUNG
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
-		bool "Use S3C UART 2 for low-level debug"
+		bool "Use Samsung S3C UART 2 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
 		  their output to UART 2. The port must have been initialised
 		  by the boot-loader before use.
 
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
 	config DEBUG_S3C_UART3
 		depends on PLAT_SAMSUNG && ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART
-		bool "Use S3C UART 3 for low-level debug"
+		bool "Use Samsung S3C UART 3 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
 		  their output to UART 3. The port must have been initialised
 		  by the boot-loader before use.
 
-		  The uncompressor code port configuration is now handled
-		  by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
 	config DEBUG_S3C2410_UART0
 		depends on ARCH_S3C24XX
 		select DEBUG_S3C2410_UART
@@ -991,6 +979,7 @@ config DEBUG_STI_UART
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/8250.S" if DEBUG_LL_UART_8250 || DEBUG_UART_8250
+	default "debug/clps711x.S" if DEBUG_CLPS711X_UART1 || DEBUG_CLPS711X_UART2
 	default "debug/pl01x.S" if DEBUG_LL_UART_PL01X || DEBUG_UART_PL01X
 	default "debug/exynos.S" if DEBUG_EXYNOS_UART
 	default "debug/efm32.S" if DEBUG_LL_UART_EFM32