Merge tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "One new core feature here, a small collection of new drivers and a
  bunch of small improvements in existing drivers:

   - A new CS_WORD flag for transfers where the chip select is toggled
     at every word, with both a generic implementation and the ability
     for controllers to do this automatically (including a DaVinci one).

   - New drivers for Mediatek MT2712, Qualcomm GENI and QSPI, Spreadtrum
     SPI and ST STM32 QSPI plus new IDs for several existing ones"

* tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (86 commits)
  spi: lpspi: add imx8qxp compatible string
  spi: Allow building SPI_BCM63XX_HSSPI on ARM-based SoCs
  spi: omap2-mcspi: Add slave mode support
  spi: omap2-mcspi: Set FIFO DMA trigger level to word length
  spi: omap2-mcspi: Switch to readl_poll_timeout()
  spi: spi-mem: add stm32 qspi controller
  dt-bindings: spi: add stm32 qspi controller
  spi: sh-msiof: document R8A779{7|8}0 bindings
  spi: pic32-sqi: don't pass GFP_DMA32 to dma_alloc_coherent
  MAINTAINERS: Add entry for Broadcom SPI controller
  spi: sh-msiof: fix deferred probing
  spi: imx: use PIO mode if size is small
  spi: imx: correct wml as the last sg length
  spi: imx: move wml setting to later than setup_transfer
  PCI: Provide pci_match_id() with CONFIG_PCI=n
  spi: Make GPIO CSs honour the SPI_NO_CS flag
  spi/spi-pxa2xx: add PXA2xx SSP SPI Controller
  spi: pxa2xx: Add devicetree support
  spi: pxa2xx: Use an enum for type
  spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
  ...

11 files changed, 215 insertions, 30 deletions

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
index ff92e5a41bed..dab7ca9f250c 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
@@ -53,20 +53,8 @@ Required properties:
 - clocks:		Serial engine core clock needed by the device.
 
 Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller
-
-Required properties:
-- compatible:		Must contain "qcom,geni-spi".
-- reg:			Must contain SPI register location and length.
-- interrupts:		Must contain SPI controller interrupts.
-- clock-names:		Must contain "se".
-- clocks:		Serial engine core clock needed by the device.
-- spi-max-frequency:	Specifies maximum SPI clock frequency, units - Hz.
-- #address-cells:	Must be <1> to define a chip select address on
-			the SPI bus.
-- #size-cells:		Must be <0>.
-
-SPI slave nodes must be children of the SPI master node and conform to SPI bus
-binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+node binding is described in
+Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt.
 
 Example:
 	geniqup@8c0000 {
@@ -103,17 +91,4 @@ Example:
 			pinctrl-1 = <&qup_1_uart_3_sleep>;
 		};
 
-		spi0: spi@a84000 {
-			compatible = "qcom,geni-spi";
-			reg = <0xa84000 0x4000>;
-			interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "se";
-			clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
-			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&qup_1_spi_2_active>;
-			pinctrl-1 = <&qup_1_spi_2_sleep>;
-			spi-max-frequency = <19200000>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
 	}
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
new file mode 100644
index 000000000000..790311a42bf1
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
@@ -0,0 +1,39 @@
+GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
+
+The QUP v3 core is a GENI based AHB slave that provides a common data path
+(an output FIFO and an input FIFO) for serial peripheral interface (SPI)
+mini-core.
+
+SPI in master mode supports up to 50MHz, up to four chip selects, programmable
+data path from 4 bits to 32 bits and numerous protocol variants.
+
+Required properties:
+- compatible:		Must contain "qcom,geni-spi".
+- reg:			Must contain SPI register location and length.
+- interrupts:		Must contain SPI controller interrupts.
+- clock-names:		Must contain "se".
+- clocks:		Serial engine core clock needed by the device.
+- #address-cells:	Must be <1> to define a chip select address on
+			the SPI bus.
+- #size-cells:		Must be <0>.
+
+SPI Controller nodes must be child of GENI based Qualcomm Universal
+Peripharal. Please refer GENI based QUP wrapper controller node bindings
+described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt.
+
+SPI slave nodes must be children of the SPI master node and conform to SPI bus
+binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+
+Example:
+	spi0: spi@a84000 {
+		compatible = "qcom,geni-spi";
+		reg = <0xa84000 0x4000>;
+		interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "se";
+		clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&qup_1_spi_2_active>;
+		pinctrl-1 = <&qup_1_spi_2_sleep>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt
new file mode 100644
index 000000000000..1d64b61f5171
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt
@@ -0,0 +1,36 @@
+Qualcomm Quad Serial Peripheral Interface (QSPI)
+
+The QSPI controller allows SPI protocol communication in single, dual, or quad
+wire transmission modes for read/write access to slaves such as NOR flash.
+
+Required properties:
+- compatible:	An SoC specific identifier followed by "qcom,qspi-v1", such as
+		"qcom,sdm845-qspi", "qcom,qspi-v1"
+- reg:		Should contain the base register location and length.
+- interrupts:	Interrupt number used by the controller.
+- clocks:	Should contain the core and AHB clock.
+- clock-names:	Should be "core" for core clock and "iface" for AHB clock.
+
+SPI slave nodes must be children of the SPI master node and can contain
+properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+	qspi: spi@88df000 {
+		compatible = "qcom,sdm845-qspi", "qcom,qspi-v1";
+		reg = <0x88df000 0x600>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "iface", "core";
+		clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			 <&gcc GCC_QSPI_CORE_CLK>;
+
+		flash@0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-max-frequency = <25000000>;
+			spi-tx-bus-width = <2>;
+			spi-rx-bus-width = <2>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt
index bfbc2035fb6b..4b836ad17b19 100644
--- a/Documentation/devicetree/bindings/spi/sh-msiof.txt
+++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt
@@ -2,7 +2,9 @@ Renesas MSIOF spi controller
 
 Required properties:
 - compatible           : "renesas,msiof-r8a7743" (RZ/G1M)
+			 "renesas,msiof-r8a7744" (RZ/G1N)
 			 "renesas,msiof-r8a7745" (RZ/G1E)
+			 "renesas,msiof-r8a774a1" (RZ/G2M)
 			 "renesas,msiof-r8a7790" (R-Car H2)
 			 "renesas,msiof-r8a7791" (R-Car M2-W)
 			 "renesas,msiof-r8a7792" (R-Car V2H)
@@ -11,10 +13,14 @@ Required properties:
 			 "renesas,msiof-r8a7795" (R-Car H3)
 			 "renesas,msiof-r8a7796" (R-Car M3-W)
 			 "renesas,msiof-r8a77965" (R-Car M3-N)
+			 "renesas,msiof-r8a77970" (R-Car V3M)
+			 "renesas,msiof-r8a77980" (R-Car V3H)
+			 "renesas,msiof-r8a77990" (R-Car E3)
+			 "renesas,msiof-r8a77995" (R-Car D3)
 			 "renesas,msiof-sh73a0" (SH-Mobile AG5)
 			 "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device)
 			 "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device)
-			 "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device)
+			 "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device)
 			 "renesas,sh-msiof"      (deprecated)
 
 			 When compatible with the generic version, nodes
diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
index 642d3fb1ef85..2864bc6b659c 100644
--- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
+++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
@@ -2,7 +2,7 @@ Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface.
 
 Required properties:
 - compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or
-  "jaguar2"
+  "jaguar2", or "amazon,alpine-dw-apb-ssi"
 - reg : The register base for the controller. For "mscc,<soc>-spi", a second
   register set is required (named ICPU_CFG:SPI_MST)
 - interrupts : One interrupt, used by the controller.
diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt
index 4af132606b37..8d178a4503cf 100644
--- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt
@@ -3,6 +3,7 @@
 Required properties:
 - compatible :
   - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc
+  - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc
 - reg : address and length of the lpspi master registers
 - interrupts : lpspi interrupt
 - clocks : lpspi clock specifier
diff --git a/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt
new file mode 100644
index 000000000000..0335a9bd2e8a
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt
@@ -0,0 +1,24 @@
+PXA2xx SSP SPI Controller
+
+Required properties:
+- compatible: Must be "marvell,mmp2-ssp".
+- reg: Offset and length of the device's register set.
+- interrupts: Should be the interrupt number.
+- clocks: Should contain a single entry describing the clock input.
+- #address-cells:  Number of cells required to define a chip select address.
+- #size-cells: Should be zero.
+
+Optional properties:
+- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
+  Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Child nodes represent devices on the SPI bus
+  See ../spi/spi-bus.txt
+
+Example:
+	ssp1: spi@d4035000 {
+		compatible = "marvell,mmp2-ssp";
+		reg = <0xd4035000 0x1000>;
+		clocks = <&soc_clocks MMP2_CLK_SSP0>;
+		interrupts = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt
index 96fd58548f69..fc97ad64fbf2 100644
--- a/Documentation/devicetree/bindings/spi/spi-rspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt
@@ -3,7 +3,7 @@ Device tree configuration for Renesas RSPI/QSPI driver
 Required properties:
 - compatible       : For Renesas Serial Peripheral Interface on legacy SH:
 		     "renesas,rspi-<soctype>", "renesas,rspi" as fallback.
-		     For Renesas Serial Peripheral Interface on RZ/A1H:
+		     For Renesas Serial Peripheral Interface on RZ/A:
 		     "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback.
 		     For Quad Serial Peripheral Interface on R-Car Gen2 and
 		     RZ/G1 devices:
@@ -11,7 +11,9 @@ Required properties:
 		     Examples with soctypes are:
 		        - "renesas,rspi-sh7757" (SH)
 			- "renesas,rspi-r7s72100" (RZ/A1H)
+			- "renesas,rspi-r7s9210" (RZ/A2)
 			- "renesas,qspi-r8a7743" (RZ/G1M)
+			- "renesas,qspi-r8a7744" (RZ/G1N)
 			- "renesas,qspi-r8a7745" (RZ/G1E)
 			- "renesas,qspi-r8a7790" (R-Car H2)
 			- "renesas,qspi-r8a7791" (R-Car M2-W)
diff --git a/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt
new file mode 100644
index 000000000000..c37e5a179b21
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt
@@ -0,0 +1,32 @@
+Binding for MTK SPI Slave controller
+
+Required properties:
+- compatible: should be one of the following.
+    - mediatek,mt2712-spi-slave: for mt2712 platforms
+- reg: Address and length of the register set for the device.
+- interrupts: Should contain spi interrupt.
+- clocks: phandles to input clocks.
+  It's clock gate, and should be <&infracfg CLK_INFRA_AO_SPI1>.
+- clock-names: should be "spi" for the clock gate.
+
+Optional properties:
+- assigned-clocks: it's mux clock, should be <&topckgen CLK_TOP_SPISLV_SEL>.
+- assigned-clock-parents: parent of mux clock.
+  It's PLL, and should be one of the following.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D2>: specify parent clock 312MHZ.
+				       It's the default one.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D4>: specify parent clock 156MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+
+Example:
+- SoC Specific Portion:
+spis1: spi@10013000 {
+	compatible = "mediatek,mt2712-spi-slave";
+	reg = <0 0x10013000 0 0x100>;
+	interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&infracfg CLK_INFRA_AO_SPI1>;
+	clock-names = "spi";
+	assigned-clocks = <&topckgen CLK_TOP_SPISLV_SEL>;
+	assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>;
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt
new file mode 100644
index 000000000000..bad211a19da4
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt
@@ -0,0 +1,26 @@
+Spreadtrum SPI Controller
+
+Required properties:
+- compatible: Should be "sprd,sc9860-spi".
+- reg: Offset and length of SPI controller register space.
+- interrupts: Should contain SPI interrupt.
+- clock-names: Should contain following entries:
+	"spi" for SPI clock,
+	"source" for SPI source (parent) clock,
+	"enable" for SPI module enable clock.
+- clocks: List of clock input name strings sorted in the same order
+	as the clock-names property.
+- #address-cells: The number of cells required to define a chip select
+	address on the SPI bus. Should be set to 1.
+- #size-cells: Should be set to 0.
+
+Example:
+spi0: spi@70a00000{
+	compatible = "sprd,sc9860-spi";
+	reg = <0 0x70a00000 0 0x1000>;
+	interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "spi", "source","enable";
+	clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
new file mode 100644
index 000000000000..adeeb63e84b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt
@@ -0,0 +1,44 @@
+* STMicroelectronics Quad Serial Peripheral Interface(QSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: the first contains the register location and length.
+       the second contains the memory mapping address and length
+- reg-names: should contain the reg names "qspi" "qspi_mm"
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash (NOR/NAND) must be a child of spi node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: see ./spi-bus.txt for the description
+
+Example:
+
+qspi: spi@a0001000 {
+	compatible = "st,stm32f469-qspi";
+	reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+	reg-names = "qspi", "qspi_mm";
+	interrupts = <91>;
+	resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+	clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi0>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		...
+	};
+};