Merge tag 'asoc-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Updates for v3.15

Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:

 - Lots of cleanups from Takashi for enumerations; the original API for
   these was error prone so he's refactored lots of code to use more
   modern APIs which avoid issues.
 - Elimination of the ASoC level wrappers for I2C and SPI moving us
   closer to converting to regmap completely and avoiding some
   randconfig hassle.
 - Provide both manually and transparently locked DAPM APIs rather than
   a mix of the two fixing some concurrency issues.
 - Start converting CODEC drivers to use separate bus interface drivers
   rather than having them all in one file helping avoid dependency
   issues.
 - DPCM support for Intel Haswell and Bay Trail platforms.
 - Lots of work on improvements for simple-card, DaVinci and the Renesas
   rcar drivers.
 - New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
   CSR SiRF SoC.

28 files changed, 506 insertions, 89 deletions

diff --git a/Documentation/ABI/testing/sysfs-tty b/Documentation/ABI/testing/sysfs-tty
index a2ccec35ffce..ad22fb0ee765 100644
--- a/Documentation/ABI/testing/sysfs-tty
+++ b/Documentation/ABI/testing/sysfs-tty
@@ -3,8 +3,7 @@ Date:		Nov 2010
 Contact:	Kay Sievers <kay.sievers@vrfy.org>
 Description:
 		 Shows the list of currently configured
-		 tty devices used for the console,
-		 like 'tty1 ttyS0'.
+		 console devices, like 'tty1 ttyS0'.
 		 The last entry in the file is the active
 		 device connected to /dev/console.
 		 The file supports poll() to detect virtual
diff --git a/Documentation/PCI/MSI-HOWTO.txt b/Documentation/PCI/MSI-HOWTO.txt
index a8d01005f480..10a93696e55a 100644
--- a/Documentation/PCI/MSI-HOWTO.txt
+++ b/Documentation/PCI/MSI-HOWTO.txt
@@ -82,7 +82,19 @@ Most of the hard work is done for the driver in the PCI layer.  It simply
 has to request that the PCI layer set up the MSI capability for this
 device.
 
-4.2.1 pci_enable_msi_range
+4.2.1 pci_enable_msi
+
+int pci_enable_msi(struct pci_dev *dev)
+
+A successful call allocates ONE interrupt to the device, regardless
+of how many MSIs the device supports.  The device is switched from
+pin-based interrupt mode to MSI mode.  The dev->irq number is changed
+to a new number which represents the message signaled interrupt;
+consequently, this function should be called before the driver calls
+request_irq(), because an MSI is delivered via a vector that is
+different from the vector of a pin-based interrupt.
+
+4.2.2 pci_enable_msi_range
 
 int pci_enable_msi_range(struct pci_dev *dev, int minvec, int maxvec)
 
@@ -147,6 +159,11 @@ static int foo_driver_enable_msi(struct pci_dev *pdev, int nvec)
 	return pci_enable_msi_range(pdev, nvec, nvec);
 }
 
+Note, unlike pci_enable_msi_exact() function, which could be also used to
+enable a particular number of MSI-X interrupts, pci_enable_msi_range()
+returns either a negative errno or 'nvec' (not negative errno or 0 - as
+pci_enable_msi_exact() does).
+
 4.2.1.3 Single MSI mode
 
 The most notorious example of the request type described above is
@@ -158,7 +175,27 @@ static int foo_driver_enable_single_msi(struct pci_dev *pdev)
 	return pci_enable_msi_range(pdev, 1, 1);
 }
 
-4.2.2 pci_disable_msi
+Note, unlike pci_enable_msi() function, which could be also used to
+enable the single MSI mode, pci_enable_msi_range() returns either a
+negative errno or 1 (not negative errno or 0 - as pci_enable_msi()
+does).
+
+4.2.3 pci_enable_msi_exact
+
+int pci_enable_msi_exact(struct pci_dev *dev, int nvec)
+
+This variation on pci_enable_msi_range() call allows a device driver to
+request exactly 'nvec' MSIs.
+
+If this function returns a negative number, it indicates an error and
+the driver should not attempt to request any more MSI interrupts for
+this device.
+
+By contrast with pci_enable_msi_range() function, pci_enable_msi_exact()
+returns zero in case of success, which indicates MSI interrupts have been
+successfully allocated.
+
+4.2.4 pci_disable_msi
 
 void pci_disable_msi(struct pci_dev *dev)
 
@@ -172,7 +209,7 @@ on any interrupt for which it previously called request_irq().
 Failure to do so results in a BUG_ON(), leaving the device with
 MSI enabled and thus leaking its vector.
 
-4.2.3 pci_msi_vec_count
+4.2.4 pci_msi_vec_count
 
 int pci_msi_vec_count(struct pci_dev *dev)
 
@@ -257,8 +294,8 @@ possible, likely up to the limit returned by pci_msix_vec_count() function:
 
 static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec)
 {
-	return pci_enable_msi_range(adapter->pdev, adapter->msix_entries,
-				    1, nvec);
+	return pci_enable_msix_range(adapter->pdev, adapter->msix_entries,
+				     1, nvec);
 }
 
 Note the value of 'minvec' parameter is 1.  As 'minvec' is inclusive,
@@ -269,8 +306,8 @@ In this case the function could look like this:
 
 static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec)
 {
-	return pci_enable_msi_range(adapter->pdev, adapter->msix_entries,
-				    FOO_DRIVER_MINIMUM_NVEC, nvec);
+	return pci_enable_msix_range(adapter->pdev, adapter->msix_entries,
+				     FOO_DRIVER_MINIMUM_NVEC, nvec);
 }
 
 4.3.1.2 Exact number of MSI-X interrupts
@@ -282,10 +319,15 @@ parameters:
 
 static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec)
 {
-	return pci_enable_msi_range(adapter->pdev, adapter->msix_entries,
-				    nvec, nvec);
+	return pci_enable_msix_range(adapter->pdev, adapter->msix_entries,
+				     nvec, nvec);
 }
 
+Note, unlike pci_enable_msix_exact() function, which could be also used to
+enable a particular number of MSI-X interrupts, pci_enable_msix_range()
+returns either a negative errno or 'nvec' (not negative errno or 0 - as
+pci_enable_msix_exact() does).
+
 4.3.1.3 Specific requirements to the number of MSI-X interrupts
 
 As noted above, there could be devices that can not operate with just any
@@ -332,7 +374,64 @@ Note how pci_enable_msix_range() return value is analized for a fallback -
 any error code other than -ENOSPC indicates a fatal error and should not
 be retried.
 
-4.3.2 pci_disable_msix
+4.3.2 pci_enable_msix_exact
+
+int pci_enable_msix_exact(struct pci_dev *dev,
+			  struct msix_entry *entries, int nvec)
+
+This variation on pci_enable_msix_range() call allows a device driver to
+request exactly 'nvec' MSI-Xs.
+
+If this function returns a negative number, it indicates an error and
+the driver should not attempt to allocate any more MSI-X interrupts for
+this device.
+
+By contrast with pci_enable_msix_range() function, pci_enable_msix_exact()
+returns zero in case of success, which indicates MSI-X interrupts have been
+successfully allocated.
+
+Another version of a routine that enables MSI-X mode for a device with
+specific requirements described in chapter 4.3.1.3 might look like this:
+
+/*
+ * Assume 'minvec' and 'maxvec' are non-zero
+ */
+static int foo_driver_enable_msix(struct foo_adapter *adapter,
+				  int minvec, int maxvec)
+{
+	int rc;
+
+	minvec = roundup_pow_of_two(minvec);
+	maxvec = rounddown_pow_of_two(maxvec);
+
+	if (minvec > maxvec)
+		return -ERANGE;
+
+retry:
+	rc = pci_enable_msix_exact(adapter->pdev,
+				   adapter->msix_entries, maxvec);
+
+	/*
+	 * -ENOSPC is the only error code allowed to be analyzed
+	 */
+	if (rc == -ENOSPC) {
+		if (maxvec == 1)
+			return -ENOSPC;
+
+		maxvec /= 2;
+
+		if (minvec > maxvec)
+			return -ENOSPC;
+
+		goto retry;
+	} else if (rc < 0) {
+		return rc;
+	}
+
+	return maxvec;
+}
+
+4.3.3 pci_disable_msix
 
 void pci_disable_msix(struct pci_dev *dev)
 
diff --git a/Documentation/device-mapper/cache.txt b/Documentation/device-mapper/cache.txt
index e6b72d355151..68c0f517c60e 100644
--- a/Documentation/device-mapper/cache.txt
+++ b/Documentation/device-mapper/cache.txt
@@ -124,12 +124,11 @@ the default being 204800 sectors (or 100MB).
 Updating on-disk metadata
 -------------------------
 
-On-disk metadata is committed every time a REQ_SYNC or REQ_FUA bio is
-written.  If no such requests are made then commits will occur every
-second.  This means the cache behaves like a physical disk that has a
-write cache (the same is true of the thin-provisioning target).  If
-power is lost you may lose some recent writes.  The metadata should
-always be consistent in spite of any crash.
+On-disk metadata is committed every time a FLUSH or FUA bio is written.
+If no such requests are made then commits will occur every second.  This
+means the cache behaves like a physical disk that has a volatile write
+cache.  If power is lost you may lose some recent writes.  The metadata
+should always be consistent in spite of any crash.
 
 The 'dirty' state for a cache block changes far too frequently for us
 to keep updating it on the fly.  So we treat it as a hint.  In normal
diff --git a/Documentation/device-mapper/thin-provisioning.txt b/Documentation/device-mapper/thin-provisioning.txt
index 8a7a3d46e0da..05a27e9442bd 100644
--- a/Documentation/device-mapper/thin-provisioning.txt
+++ b/Documentation/device-mapper/thin-provisioning.txt
@@ -116,6 +116,35 @@ Resuming a device with a new table itself triggers an event so the
 userspace daemon can use this to detect a situation where a new table
 already exceeds the threshold.
 
+A low water mark for the metadata device is maintained in the kernel and
+will trigger a dm event if free space on the metadata device drops below
+it.
+
+Updating on-disk metadata
+-------------------------
+
+On-disk metadata is committed every time a FLUSH or FUA bio is written.
+If no such requests are made then commits will occur every second.  This
+means the thin-provisioning target behaves like a physical disk that has
+a volatile write cache.  If power is lost you may lose some recent
+writes.  The metadata should always be consistent in spite of any crash.
+
+If data space is exhausted the pool will either error or queue IO
+according to the configuration (see: error_if_no_space).  If metadata
+space is exhausted or a metadata operation fails: the pool will error IO
+until the pool is taken offline and repair is performed to 1) fix any
+potential inconsistencies and 2) clear the flag that imposes repair.
+Once the pool's metadata device is repaired it may be resized, which
+will allow the pool to return to normal operation.  Note that if a pool
+is flagged as needing repair, the pool's data and metadata devices
+cannot be resized until repair is performed.  It should also be noted
+that when the pool's metadata space is exhausted the current metadata
+transaction is aborted.  Given that the pool will cache IO whose
+completion may have already been acknowledged to upper IO layers
+(e.g. filesystem) it is strongly suggested that consistency checks
+(e.g. fsck) be performed on those layers when repair of the pool is
+required.
+
 Thin provisioning
 -----------------
 
@@ -258,10 +287,9 @@ ii) Status
 	should register for the event and then check the target's status.
 
     held metadata root:
-	The location, in sectors, of the metadata root that has been
+	The location, in blocks, of the metadata root that has been
 	'held' for userspace read access.  '-' indicates there is no
-	held root.  This feature is not yet implemented so '-' is
-	always returned.
+	held root.
 
     discard_passdown|no_discard_passdown
 	Whether or not discards are actually being passed down to the
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 34dc40cffdfd..af9b4a0d902b 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -91,7 +91,7 @@ Boards:
   compatible = "ti,omap3-beagle", "ti,omap3"
 
 - OMAP3 Tobi with Overo : Commercial expansion board with daughter board
-  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+  compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3"
 
 - OMAP4 SDP : Software Development Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
index a6a352c2771e..5992dceec7af 100644
--- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
+++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
@@ -21,9 +21,9 @@ Required Properties:
     must appear in the same order as the output clocks.
   - #clock-cells: Must be 1
   - clock-output-names: The name of the clocks as free-form strings
-  - renesas,indices: Indices of the gate clocks into the group (0 to 31)
+  - renesas,clock-indices: Indices of the gate clocks into the group (0 to 31)
 
-The clocks, clock-output-names and renesas,indices properties contain one
+The clocks, clock-output-names and renesas,clock-indices properties contain one
 entry per gate clock. The MSTP groups are sparsely populated. Unimplemented
 gate clocks must not be declared.
 
diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
index 68b83ecc3850..ee9be9961524 100644
--- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -1,12 +1,16 @@
 * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
 
 Required properties:
-- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma",
-  "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma",
-  "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or
-  "fsl,imx6q-sdma". The -to variants should be preferred since they
-  allow to determnine the correct ROM script addresses needed for
-  the driver to work without additional firmware.
+- compatible : Should be one of
+      "fsl,imx25-sdma"
+      "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma"
+      "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma"
+      "fsl,imx51-sdma"
+      "fsl,imx53-sdma"
+      "fsl,imx6q-sdma"
+  The -to variants should be preferred since they allow to determnine the
+  correct ROM script addresses needed for the driver to work without additional
+  firmware.
 - reg : Should contain SDMA registers location and length
 - interrupts : Should contain SDMA interrupt
 - #dma-cells : Must be <3>.
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 1a1ac2e560e9..f47e56bcf78d 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -18,6 +18,7 @@ atmel,24c02		i2c serial eeprom  (24cxx)
 atmel,at97sc3204t	i2c trusted platform module (TPM)
 capella,cm32181		CM32181: Ambient Light Sensor
 catalyst,24c32		i2c serial eeprom
+cirrus,cs42l51		Cirrus Logic CS42L51 audio codec
 dallas,ds1307		64 x 8, Serial, I2C Real-Time Clock
 dallas,ds1338		I2C RTC with 56-Byte NV RAM
 dallas,ds1339		I2C Serial Real-Time Clock
diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
index 60960b2755f4..efc98ea1f23d 100644
--- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt
+++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
@@ -17,6 +17,14 @@ Required properties for devices compatible with "atmel,at91sam9g45-ssc":
   See Documentation/devicetree/bindings/dma/atmel-dma.txt for details.
 - dma-names: Must be "tx", "rx".
 
+Optional properties:
+  - atmel,clk-from-rk-pin: bool property.
+     - When SSC works in slave mode, according to the hardware design, the
+       clock can get from TK pin, and also can get from RK pin. So, add
+       this parameter to choose where the clock from.
+     - By default the clock is from TK pin, if the clock from RK pin, this
+       property is needed.
+
 Examples:
 - PDC transfer:
 ssc0: ssc@fffbc000 {
diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt
new file mode 100644
index 000000000000..2dc127c30d9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt
@@ -0,0 +1,22 @@
+* OpenCores MAC 10/100 Mbps
+
+Required properties:
+- compatible: Should be "opencores,ethoc".
+- reg: two memory regions (address and length),
+  first region is for the device registers and descriptor rings,
+  second is for the device packet memory.
+- interrupts: interrupt for the device.
+
+Optional properties:
+- clocks: phandle to refer to the clk used as per
+  Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Examples:
+
+	enet0: ethoc@fd030000 {
+		compatible = "opencores,ethoc";
+		reg = <0xfd030000 0x4000 0xfd800000 0x4000>;
+		interrupts = <1>;
+		local-mac-address = [00 50 c2 13 6f 00];
+		clocks = <&osc>;
+        };
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 000000000000..3dd3d0bf112f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible	: Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+   "st,stid127-dwmac".
+ - reg		: Offset of the glue configuration register map in system
+   configuration regmap pointed by st,syscon property and size.
+
+ - reg-names	: Should be "sti-ethconf".
+
+ - st,syscon	: Should be phandle to system configuration node which
+   encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+   wired up in from different sources. One via TXCLK pin and other via CLK_125
+   pin. This wiring is totally board dependent. However the retiming glue
+   logic should be configured accordingly. Possible values for this property
+
+	   "txclk" - if 125Mhz clock is wired up via txclk line.
+	   "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+   This property is only valid for Giga bit setup( GMII, RGMII), and it is
+   un-used for non-giga bit (MII and RMII) setups. Also note that internal
+   clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+  for tx and rx. This property is only valid for RMII case where the clock can
+  be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+	device_type 	= "network";
+	compatible	= "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+	reg 		= <0xfe810000 0x8000>, <0x8bc 0x4>;
+	reg-names	= "stmmaceth", "sti-ethconf";
+	interrupts	= <0 133 0>, <0 134 0>, <0 135 0>;
+	interrupt-names	= "macirq", "eth_wake_irq", "eth_lpi";
+	phy-mode	= "mii";
+
+	st,syscon	= <&syscfg_rear>;
+
+	snps,pbl 	= <32>;
+	snps,mixed-burst;
+
+	resets		= <&softreset STIH416_ETH0_SOFTRESET>;
+	reset-names	= "stmmaceth";
+	pinctrl-0	= <&pinctrl_mii0>;
+	pinctrl-names 	= "default";
+	clocks		= <&CLK_S_GMAC0_PHY>;
+	clock-names	= "stmmaceth";
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt
index 9e9e9ef9f852..c119debe6bab 100644
--- a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt
@@ -1,4 +1,4 @@
-Broadcom Capri Pin Controller
+Broadcom BCM281xx Pin Controller
 
 This is a pin controller for the Broadcom BCM281xx SoC family, which includes
 BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
@@ -7,14 +7,14 @@ BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
 
 Required Properties:
 
-- compatible:	Must be "brcm,capri-pinctrl".
+- compatible:	Must be "brcm,bcm11351-pinctrl"
 - reg:		Base address of the PAD Controller register block and the size
 		of the block.
 
 For example, the following is the bare minimum node:
 
 	pinctrl@35004800 {
-		compatible = "brcm,capri-pinctrl";
+		compatible = "brcm,bcm11351-pinctrl";
 		reg = <0x35004800 0x430>;
 	};
 
@@ -119,7 +119,7 @@ Optional Properties (for HDMI pins):
 Example:
 // pin controller node
 pinctrl@35004800 {
-	compatible = "brcm,capri-pinctrl";
+	compatible = "brcmbcm11351-pinctrl";
 	reg = <0x35004800 0x430>;
 
 	// pin configuration node
diff --git a/Documentation/devicetree/bindings/sound/da9055.txt b/Documentation/devicetree/bindings/sound/da9055.txt
new file mode 100644
index 000000000000..ed1b7cc6f249
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/da9055.txt
@@ -0,0 +1,22 @@
+* Dialog DA9055 Audio CODEC
+
+DA9055 provides Audio CODEC support (I2C only).
+
+The Audio CODEC device in DA9055 has it's own I2C address which is configurable,
+so the device is instantiated separately from the PMIC (MFD) device.
+
+For details on accompanying PMIC I2C device, see the following:
+Documentation/devicetree/bindings/mfd/da9055.txt
+
+Required properties:
+
+  - compatible: "dlg,da9055-codec"
+  - reg: Specifies the I2C slave address
+
+
+Example:
+
+	codec: da9055-codec@1a {
+		compatible = "dlg,da9055-codec";
+		reg = <0x1a>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
index 865178d5cdf3..963e100514c2 100644
--- a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
+++ b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
@@ -5,12 +5,19 @@ Required properties:
 - ti,model : The user-visible name of this sound complex.
 - ti,audio-codec : The phandle of the TLV320AIC3x audio codec
 - ti,mcasp-controller : The phandle of the McASP controller
-- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec
 - ti,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
   the second being the connection's source. Valid names for sources and
   sinks are the codec's pins, and the jacks on the board:
 
+Optional properties:
+- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec.
+- clocks : Reference to the master clock
+- clock-names : The clock should be named "mclk"
+- Either codec-clock-rate or the codec-clock reference has to be defined. If
+  the both are defined the driver attempts to set referenced clock to the
+  defined rate and takes the rate from the clock reference.
+
   Board connectors:
 
   * Headphone Jack
diff --git a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt
new file mode 100644
index 000000000000..0d7985c864af
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt
@@ -0,0 +1,21 @@
+Audio complex for Eukrea boards with tlv320aic23 codec.
+
+Required properties:
+- compatible : "eukrea,asoc-tlv320"
+- eukrea,model : The user-visible name of this sound complex.
+- ssi-controller : The phandle of the SSI controller.
+- fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX).
+- fsl,mux-ext-port : The external port of the i.MX audio muxer.
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+	sound {
+		compatible = "eukrea,asoc-tlv320";
+		eukrea,model = "imx51-eukrea-tlv320aic23";
+		ssi-controller = <&ssi2>;
+		fsl,mux-int-port = <2>;
+		fsl,mux-ext-port = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt
index d7b99fa637b5..aeb8c4a0b88d 100644
--- a/Documentation/devicetree/bindings/sound/fsl,esai.txt
+++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt
@@ -34,6 +34,10 @@ Required properties:
     that ESAI would work in the synchronous mode, which means all the settings
     for Receiving would be duplicated from Transmition related registers.
 
+  - big-endian : If this property is absent, the native endian mode will
+    be in use as default, or the big endian mode will be in use for all the
+    device registers.
+
 Example:
 
 esai: esai@02024000 {
@@ -46,5 +50,6 @@ esai: esai@02024000 {
 	dma-names = "rx", "tx";
 	fsl,fifo-depth = <128>;
 	fsl,esai-synchronous;
+	big-endian;
 	status = "disabled";
 };
diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt
index f2ae335670f5..3e9e82c8eab3 100644
--- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt
+++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt
@@ -29,6 +29,10 @@ Required properties:
 			can also be referred to TxClk_Source
 			bit of register SPDIF_STC.
 
+   - big-endian : If this property is absent, the native endian mode will
+   be in use as default, or the big endian mode will be in use for all the
+   device registers.
+
 Example:
 
 spdif: spdif@02004000 {
@@ -50,5 +54,6 @@ spdif: spdif@02004000 {
 		"rxtx5", "rxtx6",
 		"rxtx7";
 
+	big-endian;
 	status = "okay";
 };
diff --git a/Documentation/devicetree/bindings/sound/pcm512x.txt b/Documentation/devicetree/bindings/sound/pcm512x.txt
new file mode 100644
index 000000000000..faff75e64573
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/pcm512x.txt
@@ -0,0 +1,30 @@
+PCM512x audio CODECs
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : One of "ti,pcm5121" or "ti,pcm5122"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+  - AVDD-supply, DVDD-supply, and CPVDD-supply : power supplies for the
+    device, as covered in bindings/regulator/regulator.txt
+
+Optional properties:
+
+  - clocks : A clock specifier for the clock connected as SCLK.  If this
+    is absent the device will be configured to clock from BCLK.
+
+Example:
+
+	pcm5122: pcm5122@4c {
+		compatible = "ti,pcm5122";
+		reg = <0x4c>;
+
+		AVDD-supply = <&reg_3v3_analog>;
+		DVDD-supply = <&reg_1v8>;
+		CPVDD-supply = <&reg_3v3>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt
index 19c84df5fffa..b30c222f9cd3 100644
--- a/Documentation/devicetree/bindings/sound/simple-card.txt
+++ b/Documentation/devicetree/bindings/sound/simple-card.txt
@@ -8,13 +8,18 @@ Required properties:
 
 Optional properties:
 
+- simple-audio-card,name		: User specified audio sound card name, one string
+					  property.
 - simple-audio-card,format		: CPU/CODEC common audio format.
 					  "i2s", "right_j", "left_j" , "dsp_a"
 					  "dsp_b", "ac97", "pdm", "msb", "lsb"
+- simple-audio-card,widgets		: Please refer to widgets.txt.
 - simple-audio-card,routing		: A list of the connections between audio components.
 					  Each entry is a pair of strings, the first being the
 					  connection's sink, the second being the connection's
 					  source.
+- dai-tdm-slot-num			: Please refer to tdm-slot.txt.
+- dai-tdm-slot-width			: Please refer to tdm-slot.txt.
 
 Required subnodes:
 
@@ -42,11 +47,19 @@ Example:
 
 sound {
 	compatible = "simple-audio-card";
+	simple-audio-card,name = "VF610-Tower-Sound-Card";
 	simple-audio-card,format = "left_j";
+	simple-audio-card,widgets =
+		"Microphone", "Microphone Jack",
+		"Headphone", "Headphone Jack",
+		"Speaker", "External Speaker";
 	simple-audio-card,routing =
-		"MIC_IN", "Mic Jack",
+		"MIC_IN", "Microphone Jack",
 		"Headphone Jack", "HP_OUT",
-		"Ext Spk", "LINE_OUT";
+		"External Speaker", "LINE_OUT";
+
+	dai-tdm-slot-num = <2>;
+	dai-tdm-slot-width = <8>;
 
 	simple-audio-card,cpu {
 		sound-dai = <&sh_fsi2 0>;
diff --git a/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt b/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
new file mode 100644
index 000000000000..062f5ec36f9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
@@ -0,0 +1,17 @@
+SiRF internal audio CODEC
+
+Required properties:
+
+  - compatible : "sirf,atlas6-audio-codec" or "sirf,prima2-audio-codec"
+
+  - reg : the register address of the device.
+
+  - clocks: the clock of SiRF internal audio codec
+
+Example:
+
+audiocodec: audiocodec@b0040000 {
+	compatible = "sirf,atlas6-audio-codec";
+	reg = <0xb0040000 0x10000>;
+	clocks = <&clks 27>;
+};
diff --git a/Documentation/devicetree/bindings/sound/sirf-audio-port.txt b/Documentation/devicetree/bindings/sound/sirf-audio-port.txt
new file mode 100644
index 000000000000..1f66de3c8f00
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/sirf-audio-port.txt
@@ -0,0 +1,20 @@
+* SiRF SoC audio port
+
+Required properties:
+- compatible: "sirf,audio-port"
+- reg: Base address and size entries:
+- dmas: List of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: Identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+  One of the DMA channels will be responsible for transmission (should be
+  named "tx") and one for reception (should be named "rx").
+
+Example:
+
+audioport: audioport@b0040000 {
+	compatible = "sirf,audio-port";
+	reg = <0xb0040000 0x10000>;
+	dmas = <&dmac1 3>, <&dmac1 8>;
+	dma-names = "rx", "tx";
+};
diff --git a/Documentation/devicetree/bindings/sound/sirf-audio.txt b/Documentation/devicetree/bindings/sound/sirf-audio.txt
new file mode 100644
index 000000000000..c88882ca3704
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/sirf-audio.txt
@@ -0,0 +1,41 @@
+* SiRF atlas6 and prima2 internal audio codec and port based audio setups
+
+Required properties:
+- compatible: "sirf,sirf-audio-card"
+- sirf,audio-platform: phandle for the platform node
+- sirf,audio-codec: phandle for the SiRF internal codec node
+
+Optional properties:
+- hp-pa-gpios: Need to be present if the board need control external
+  headphone amplifier.
+- spk-pa-gpios: Need to be present if the board need control external
+  speaker amplifier.
+- hp-switch-gpios: Need to be present if the board capable to detect jack
+  insertion, removal.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Ext Spk
+ * Line In
+ * Mic
+
+SiRF internal audio codec pins:
+ * HPOUTL
+ * HPOUTR
+ * SPKOUT
+ * Ext Mic
+ * Mic Bias
+
+Example:
+
+sound {
+		compatible = "sirf,sirf-audio-card";
+		sirf,audio-codec = <&audiocodec>;
+		sirf,audio-platform = <&audioport>;
+		hp-pa-gpios = <&gpio 44 0>;
+		spk-pa-gpios = <&gpio 46 0>;
+		hp-switch-gpios = <&gpio 45 0>;
+};
+
diff --git a/Documentation/devicetree/bindings/sound/tdm-slot.txt b/Documentation/devicetree/bindings/sound/tdm-slot.txt
new file mode 100644
index 000000000000..6a2c84247f91
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/tdm-slot.txt
@@ -0,0 +1,20 @@
+TDM slot:
+
+This specifies audio DAI's TDM slot.
+
+TDM slot properties:
+dai-tdm-slot-num : Number of slots in use.
+dai-tdm-slot-width :  Width in bits for each slot.
+
+For instance:
+	dai-tdm-slot-num = <2>;
+	dai-tdm-slot-width = <8>;
+
+And for each spcified driver, there could be one .of_xlate_tdm_slot_mask()
+to specify a explicit mapping of the channels and the slots. If it's absent
+the default snd_soc_of_xlate_tdm_slot_mask() will be used to generating the
+tx and rx masks.
+
+For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit
+for an active slot as default, and the default active bits are at the LSB of
+the masks.
diff --git a/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt
new file mode 100644
index 000000000000..5e2741af27be
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt
@@ -0,0 +1,30 @@
+Texas Instruments - tlv320aic32x4 Codec module
+
+The tlv320aic32x4 serial control bus communicates through I2C protocols
+
+Required properties:
+ - compatible: Should be "ti,tlv320aic32x4"
+ - reg: I2C slave address
+ - supply-*: Required supply regulators are:
+    "iov" - digital IO power supply
+    "ldoin" - LDO power supply
+    "dv" - Digital core power supply
+    "av" - Analog core power supply
+    If you supply ldoin, dv and av are optional. Otherwise they are required
+   See regulator/regulator.txt for more information about the detailed binding
+   format.
+
+Optional properties:
+ - reset-gpios: Reset-GPIO phandle with args as described in gpio/gpio.txt
+ - clocks/clock-names: Clock named 'mclk' for the master clock of the codec.
+   See clock/clock-bindings.txt for information about the detailed format.
+
+
+Example:
+
+codec: tlv320aic32x4@18 {
+	compatible = "ti,tlv320aic32x4";
+	reg = <0x18>;
+	clocks = <&clks 201>;
+	clock-names = "mclk";
+};
diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
index 9d8ea14db490..5e6040c2c2e9 100644
--- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
+++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
@@ -6,7 +6,6 @@ Required properties:
 
 - compatible - "string" - One of:
     "ti,tlv320aic3x" - Generic TLV320AIC3x device
-    "ti,tlv320aic32x4" - TLV320AIC32x4
     "ti,tlv320aic33" - TLV320AIC33
     "ti,tlv320aic3007" - TLV320AIC3007
     "ti,tlv320aic3106" - TLV320AIC3106
diff --git a/Documentation/devicetree/bindings/sound/widgets.txt b/Documentation/devicetree/bindings/sound/widgets.txt
new file mode 100644
index 000000000000..b6de5ba3b2de
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/widgets.txt
@@ -0,0 +1,20 @@
+Widgets:
+
+This mainly specifies audio off-codec DAPM widgets.
+
+Each entry is a pair of strings in DT:
+
+	"template-wname", "user-supplied-wname"
+
+The "template-wname" being the template widget name and currently includes:
+"Microphone", "Line", "Headphone" and "Speaker".
+
+The "user-supplied-wname" being the user specified widget name.
+
+For instance:
+	simple-audio-widgets =
+		"Microphone", "Microphone Jack",
+		"Line", "Line In Jack",
+		"Line", "Line Out Jack",
+		"Headphone", "Headphone Jack",
+		"Speaker", "Speaker External";
diff --git a/Documentation/networking/3c505.txt b/Documentation/networking/3c505.txt
deleted file mode 100644
index 72f38b13101d..000000000000
--- a/Documentation/networking/3c505.txt
+++ /dev/null
@@ -1,45 +0,0 @@
-The 3Com Etherlink Plus (3c505) driver.
-
-This driver now uses DMA.  There is currently no support for PIO operation.
-The default DMA channel is 6; this is _not_ autoprobed, so you must
-make sure you configure it correctly.  If loading the driver as a
-module, you can do this with "modprobe 3c505 dma=n".  If the driver is
-linked statically into the kernel, you must either use an "ether="
-statement on the command line, or change the definition of ELP_DMA in 3c505.h.
-
-The driver will warn you if it has to fall back on the compiled in
-default DMA channel. 
-
-If no base address is given at boot time, the driver will autoprobe
-ports 0x300, 0x280 and 0x310 (in that order).  If no IRQ is given, the driver
-will try to probe for it.
-
-The driver can be used as a loadable module.
-
-Theoretically, one instance of the driver can now run multiple cards,
-in the standard way (when loading a module, say "modprobe 3c505
-io=0x300,0x340 irq=10,11 dma=6,7" or whatever).  I have not tested
-this, though.
-
-The driver may now support revision 2 hardware; the dependency on
-being able to read the host control register has been removed.  This
-is also untested, since I don't have a suitable card.
-
-Known problems:
- I still see "DMA upload timed out" messages from time to time.  These
-seem to be fairly non-fatal though.
- The card is old and slow.
-
-To do:
- Improve probe/setup code
- Test multicast and promiscuous operation
-
-Authors:
- The driver is mainly written by Craig Southeren, email
- <craigs@ineluki.apana.org.au>.
- Parts of the driver (adapting the driver to 1.1.4+ kernels,
- IRQ/address detection, some changes) and this README by
- Juha Laiho <jlaiho@ichaos.nullnet.fi>.
- DMA mode, more fixes, etc, by Philip Blundell <pjb27@cam.ac.uk>
- Multicard support, Software configurable DMA, etc., by
- Christopher Collins <ccollins@pcug.org.au>
diff --git a/Documentation/networking/can.txt b/Documentation/networking/can.txt
index f3089d423515..0cbe6ec22d6f 100644
--- a/Documentation/networking/can.txt
+++ b/Documentation/networking/can.txt
@@ -554,12 +554,6 @@ solution for a couple of reasons:
   not specified in the struct can_frame and therefore it is only valid in
   CANFD_MTU sized CAN FD frames.
 
-  As long as the payload length is <=8 the received CAN frames from CAN FD
-  capable CAN devices can be received and read by legacy sockets too. When
-  user-generated CAN FD frames have a payload length <=8 these can be send
-  by legacy CAN network interfaces too. Sending CAN FD frames with payload
-  length > 8 to a legacy CAN network interface returns an -EMSGSIZE error.
-
   Implementation hint for new CAN applications:
 
   To build a CAN FD aware application use struct canfd_frame as basic CAN