diff options
author | Benjamin Herrenschmidt <benh@kernel.crashing.org> | 2009-06-26 10:58:01 +0400 |
---|---|---|
committer | Benjamin Herrenschmidt <benh@kernel.crashing.org> | 2009-06-26 10:58:01 +0400 |
commit | fd0cca754f3f6756bfdafe500e4f49b1b9e9723f (patch) | |
tree | b1eb43fb2fb068ed5fc92b031e3ae853e599af9c /Documentation/powerpc | |
parent | 5ba762c9bb3ce2cc11e9e111cb3c476e84b91668 (diff) | |
parent | 66c6b856d8738278a4a6e558d25c90e9950aa112 (diff) | |
download | linux-fd0cca754f3f6756bfdafe500e4f49b1b9e9723f.tar.xz |
Merge commit 'kumar/next' into merge
Diffstat (limited to 'Documentation/powerpc')
-rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 1168 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/emac.txt | 148 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/gpio/gpio.txt | 50 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/gpio/mdio.txt | 19 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/marvell.txt | 521 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/phy.txt | 25 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/spi-bus.txt | 57 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/usb-ehci.txt | 25 | ||||
-rw-r--r-- | Documentation/powerpc/dts-bindings/xilinx.txt | 295 |
9 files changed, 1142 insertions, 1166 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 8d999d862d0e..79f533f38c61 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -1238,1122 +1238,7 @@ descriptions for the SOC devices for which new nodes have been defined; this list will expand as more and more SOC-containing platforms are moved over to use the flattened-device-tree model. - a) PHY nodes - - Required properties: - - - device_type : Should be "ethernet-phy" - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - linux,phandle : phandle for this node; likely referenced by an - ethernet controller node. - - - Example: - - ethernet-phy@0 { - linux,phandle = <2452000> - interrupt-parent = <40000>; - interrupts = <35 1>; - reg = <0>; - device_type = "ethernet-phy"; - }; - - - b) Interrupt controllers - - Some SOC devices contain interrupt controllers that are different - from the standard Open PIC specification. The SOC device nodes for - these types of controllers should be specified just like a standard - OpenPIC controller. Sense and level information should be encoded - as specified in section 2) of this chapter for each device that - specifies an interrupt. - - Example : - - pic@40000 { - linux,phandle = <40000>; - interrupt-controller; - #address-cells = <0>; - reg = <40000 40000>; - compatible = "chrp,open-pic"; - device_type = "open-pic"; - }; - - c) 4xx/Axon EMAC ethernet nodes - - The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a ths - special McMAL DMA controller, and sometimes an RGMII or ZMII - interface. In addition to the nodes and properties described - below, the node for the OPB bus on which the EMAC sits must have a - correct clock-frequency property. - - i) The EMAC node itself - - Required properties: - - device_type : "network" - - - compatible : compatible list, contains 2 entries, first is - "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, - 405gp, Axon) and second is either "ibm,emac" or - "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", - "ibm,emac4" - - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> - - interrupt-parent : optional, if needed for interrupt mapping - - reg : <registers mapping> - - local-mac-address : 6 bytes, MAC address - - mal-device : phandle of the associated McMAL node - - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated - with this EMAC - - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated - with this EMAC - - cell-index : 1 cell, hardware index of the EMAC cell on a given - ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on - each Axon chip) - - max-frame-size : 1 cell, maximum frame size supported in bytes - - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048 - - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048. - - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate - thresholds). - For Axon, 0x00000010 - - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) - in bytes. - For Axon, 0x00000100 (I think ...) - - phy-mode : string, mode of operations of the PHY interface. - Supported values are: "mii", "rmii", "smii", "rgmii", - "tbi", "gmii", rtbi", "sgmii". - For Axon on CAB, it is "rgmii" - - mdio-device : 1 cell, required iff using shared MDIO registers - (440EP). phandle of the EMAC to use to drive the - MDIO lines for the PHY used by this EMAC. - - zmii-device : 1 cell, required iff connected to a ZMII. phandle of - the ZMII device node - - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII - channel or 0xffffffff if ZMII is only used for MDIO. - - rgmii-device : 1 cell, required iff connected to an RGMII. phandle - of the RGMII device node. - For Axon: phandle of plb5/plb4/opb/rgmii - - rgmii-channel : 1 cell, required iff connected to an RGMII. Which - RGMII channel is used by this EMAC. - Fox Axon: present, whatever value is appropriate for each - EMAC, that is the content of the current (bogus) "phy-port" - property. - - Optional properties: - - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, - a search is performed. - - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY - for, used if phy-address is absent. bit 0x00000001 is - MDIO address 0. - For Axon it can be absent, though my current driver - doesn't handle phy-address yet so for now, keep - 0x00ffffff in it. - - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - rx-fifo-size). For Axon, either absent or 2048. - - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - tx-fifo-size). For Axon, either absent or 2048. - - tah-device : 1 cell, optional. If connected to a TAH engine for - offload, phandle of the TAH device node. - - tah-channel : 1 cell, optional. If appropriate, channel used on the - TAH engine. - - Example: - - EMAC0: ethernet@40000800 { - device_type = "network"; - compatible = "ibm,emac-440gp", "ibm,emac"; - interrupt-parent = <&UIC1>; - interrupts = <1c 4 1d 4>; - reg = <40000800 70>; - local-mac-address = [00 04 AC E3 1B 1E]; - mal-device = <&MAL0>; - mal-tx-channel = <0 1>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <5dc>; - rx-fifo-size = <1000>; - tx-fifo-size = <800>; - phy-mode = "rmii"; - phy-map = <00000001>; - zmii-device = <&ZMII0>; - zmii-channel = <0>; - }; - - ii) McMAL node - - Required properties: - - device_type : "dma-controller" - - compatible : compatible list, containing 2 entries, first is - "ibm,mcmal-CHIP" where CHIP is the host ASIC (like - emac) and the second is either "ibm,mcmal" or - "ibm,mcmal2". - For Axon, "ibm,mcmal-axon","ibm,mcmal2" - - interrupts : <interrupt mapping for the MAL interrupts sources: - 5 sources: tx_eob, rx_eob, serr, txde, rxde>. - For Axon: This is _different_ from the current - firmware. We use the "delayed" interrupts for txeob - and rxeob. Thus we end up with mapping those 5 MPIC - interrupts, all level positive sensitive: 10, 11, 32, - 33, 34 (in decimal) - - dcr-reg : < DCR registers range > - - dcr-parent : if needed for dcr-reg - - num-tx-chans : 1 cell, number of Tx channels - - num-rx-chans : 1 cell, number of Rx channels - - iii) ZMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,zmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,zmii". - For Axon, there is no ZMII node. - - reg : <registers mapping> - - iv) RGMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,rgmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,rgmii". - For Axon, "ibm,rgmii-axon","ibm,rgmii" - - reg : <registers mapping> - - revision : as provided by the RGMII new version register if - available. - For Axon: 0x0000012a - - d) Xilinx IP cores - - The Xilinx EDK toolchain ships with a set of IP cores (devices) for use - in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range - of standard device types (network, serial, etc.) and miscellaneous - devices (gpio, LCD, spi, etc). Also, since these devices are - implemented within the fpga fabric every instance of the device can be - synthesised with different options that change the behaviour. - - Each IP-core has a set of parameters which the FPGA designer can use to - control how the core is synthesized. Historically, the EDK tool would - extract the device parameters relevant to device drivers and copy them - into an 'xparameters.h' in the form of #define symbols. This tells the - device drivers how the IP cores are configured, but it requres the kernel - to be recompiled every time the FPGA bitstream is resynthesized. - - The new approach is to export the parameters into the device tree and - generate a new device tree each time the FPGA bitstream changes. The - parameters which used to be exported as #defines will now become - properties of the device node. In general, device nodes for IP-cores - will take the following form: - - (name): (generic-name)@(base-address) { - compatible = "xlnx,(ip-core-name)-(HW_VER)" - [, (list of compatible devices), ...]; - reg = <(baseaddr) (size)>; - interrupt-parent = <&interrupt-controller-phandle>; - interrupts = < ... >; - xlnx,(parameter1) = "(string-value)"; - xlnx,(parameter2) = <(int-value)>; - }; - - (generic-name): an open firmware-style name that describes the - generic class of device. Preferably, this is one word, such - as 'serial' or 'ethernet'. - (ip-core-name): the name of the ip block (given after the BEGIN - directive in system.mhs). Should be in lowercase - and all underscores '_' converted to dashes '-'. - (name): is derived from the "PARAMETER INSTANCE" value. - (parameter#): C_* parameters from system.mhs. The C_ prefix is - dropped from the parameter name, the name is converted - to lowercase and all underscore '_' characters are - converted to dashes '-'. - (baseaddr): the baseaddr parameter value (often named C_BASEADDR). - (HW_VER): from the HW_VER parameter. - (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). - - Typically, the compatible list will include the exact IP core version - followed by an older IP core version which implements the same - interface or any other device with the same interface. - - 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. - - For example, the following block from system.mhs: - - BEGIN opb_uartlite - PARAMETER INSTANCE = opb_uartlite_0 - PARAMETER HW_VER = 1.00.b - PARAMETER C_BAUDRATE = 115200 - PARAMETER C_DATA_BITS = 8 - PARAMETER C_ODD_PARITY = 0 - PARAMETER C_USE_PARITY = 0 - PARAMETER C_CLK_FREQ = 50000000 - PARAMETER C_BASEADDR = 0xEC100000 - PARAMETER C_HIGHADDR = 0xEC10FFFF - BUS_INTERFACE SOPB = opb_7 - PORT OPB_Clk = CLK_50MHz - PORT Interrupt = opb_uartlite_0_Interrupt - PORT RX = opb_uartlite_0_RX - PORT TX = opb_uartlite_0_TX - PORT OPB_Rst = sys_bus_reset_0 - END - - becomes the following device tree node: - - opb_uartlite_0: serial@ec100000 { - device_type = "serial"; - compatible = "xlnx,opb-uartlite-1.00.b"; - reg = <ec100000 10000>; - interrupt-parent = <&opb_intc_0>; - interrupts = <1 0>; // got this from the opb_intc parameters - current-speed = <d#115200>; // standard serial device prop - clock-frequency = <d#50000000>; // standard serial device prop - xlnx,data-bits = <8>; - xlnx,odd-parity = <0>; - xlnx,use-parity = <0>; - }; - - Some IP cores actually implement 2 or more logical devices. In - this case, the device should still describe the whole IP core with - a single node and add a child node for each logical device. The - ranges property can be used to translate from parent IP-core to the - registers of each device. In addition, the parent node should be - compatible with the bus type 'xlnx,compound', and should contain - #address-cells and #size-cells, as with any other bus. (Note: this - makes the assumption that both logical devices have the same bus - binding. If this is not true, then separate nodes should be used - for each logical device). The 'cell-index' property can be used to - enumerate logical devices within an IP core. For example, the - following is the system.mhs entry for the dual ps2 controller found - on the ml403 reference design. - - BEGIN opb_ps2_dual_ref - PARAMETER INSTANCE = opb_ps2_dual_ref_0 - PARAMETER HW_VER = 1.00.a - PARAMETER C_BASEADDR = 0xA9000000 - PARAMETER C_HIGHADDR = 0xA9001FFF - BUS_INTERFACE SOPB = opb_v20_0 - PORT Sys_Intr1 = ps2_1_intr - PORT Sys_Intr2 = ps2_2_intr - PORT Clkin1 = ps2_clk_rx_1 - PORT Clkin2 = ps2_clk_rx_2 - PORT Clkpd1 = ps2_clk_tx_1 - PORT Clkpd2 = ps2_clk_tx_2 - PORT Rx1 = ps2_d_rx_1 - PORT Rx2 = ps2_d_rx_2 - PORT Txpd1 = ps2_d_tx_1 - PORT Txpd2 = ps2_d_tx_2 - END - - It would result in the following device tree nodes: - - opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "xlnx,compound"; - ranges = <0 a9000000 2000>; - // If this device had extra parameters, then they would - // go here. - ps2@0 { - compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; - reg = <0 40>; - interrupt-parent = <&opb_intc_0>; - interrupts = <3 0>; - cell-index = <0>; - }; - ps2@1000 { - compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; - reg = <1000 40>; - interrupt-parent = <&opb_intc_0>; - interrupts = <3 0>; - cell-index = <0>; - }; - }; - - Also, the system.mhs file defines bus attachments from the processor - to the devices. The device tree structure should reflect the bus - attachments. Again an example; this system.mhs fragment: - - BEGIN ppc405_virtex4 - PARAMETER INSTANCE = ppc405_0 - PARAMETER HW_VER = 1.01.a - BUS_INTERFACE DPLB = plb_v34_0 - BUS_INTERFACE IPLB = plb_v34_0 - END - - BEGIN opb_intc - PARAMETER INSTANCE = opb_intc_0 - PARAMETER HW_VER = 1.00.c - PARAMETER C_BASEADDR = 0xD1000FC0 - PARAMETER C_HIGHADDR = 0xD1000FDF - BUS_INTERFACE SOPB = opb_v20_0 - END - - BEGIN opb_uart16550 - PARAMETER INSTANCE = opb_uart16550_0 - PARAMETER HW_VER = 1.00.d - PARAMETER C_BASEADDR = 0xa0000000 - PARAMETER C_HIGHADDR = 0xa0001FFF - BUS_INTERFACE SOPB = opb_v20_0 - END - - BEGIN plb_v34 - PARAMETER INSTANCE = plb_v34_0 - PARAMETER HW_VER = 1.02.a - END - - BEGIN plb_bram_if_cntlr - PARAMETER INSTANCE = plb_bram_if_cntlr_0 - PARAMETER HW_VER = 1.00.b - PARAMETER C_BASEADDR = 0xFFFF0000 - PARAMETER C_HIGHADDR = 0xFFFFFFFF - BUS_INTERFACE SPLB = plb_v34_0 - END - - BEGIN plb2opb_bridge - PARAMETER INSTANCE = plb2opb_bridge_0 - PARAMETER HW_VER = 1.01.a - PARAMETER C_RNG0_BASEADDR = 0x20000000 - PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF - PARAMETER C_RNG1_BASEADDR = 0x60000000 - PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF - PARAMETER C_RNG2_BASEADDR = 0x80000000 - PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF - PARAMETER C_RNG3_BASEADDR = 0xC0000000 - PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF - BUS_INTERFACE SPLB = plb_v34_0 - BUS_INTERFACE MOPB = opb_v20_0 - END - - Gives this device tree (some properties removed for clarity): - - plb@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "xlnx,plb-v34-1.02.a"; - device_type = "ibm,plb"; - ranges; // 1:1 translation - - plb_bram_if_cntrl_0: bram@ffff0000 { - reg = <ffff0000 10000>; - } - - opb@20000000 { - #address-cells = <1>; - #size-cells = <1>; - ranges = <20000000 20000000 20000000 - 60000000 60000000 20000000 - 80000000 80000000 40000000 - c0000000 c0000000 20000000>; - - opb_uart16550_0: serial@a0000000 { - reg = <a00000000 2000>; - }; - - opb_intc_0: interrupt-controller@d1000fc0 { - reg = <d1000fc0 20>; - }; - }; - }; - - That covers the general approach to binding xilinx IP cores into the - device tree. The following are bindings for specific devices: - - i) Xilinx ML300 Framebuffer - - Simple framebuffer device from the ML300 reference design (also on the - ML403 reference design as well as others). - - Optional properties: - - resolution = <xres yres> : pixel resolution of framebuffer. Some - implementations use a different resolution. - Default is <d#640 d#480> - - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory. - Default is <d#1024 d#480>. - - rotate-display (empty) : rotate display 180 degrees. - - ii) Xilinx SystemACE - - The Xilinx SystemACE device is used to program FPGAs from an FPGA - bitstream stored on a CF card. It can also be used as a generic CF - interface device. - - Optional properties: - - 8-bit (empty) : Set this property for SystemACE in 8 bit mode - - iii) Xilinx EMAC and Xilinx TEMAC - - Xilinx Ethernet devices. In addition to general xilinx properties - listed above, nodes for these devices should include a phy-handle - property, and may include other common network device properties - like local-mac-address. - - iv) Xilinx Uartlite - - Xilinx uartlite devices are simple fixed speed serial ports. - - Required properties: - - current-speed : Baud rate of uartlite - - v) Xilinx hwicap - - Xilinx hwicap devices provide access to the configuration logic - of the FPGA through the Internal Configuration Access Port - (ICAP). The ICAP enables partial reconfiguration of the FPGA, - readback of the configuration information, and some control over - 'warm boots' of the FPGA fabric. - - Required properties: - - xlnx,family : The family of the FPGA, necessary since the - capabilities of the underlying ICAP hardware - differ between different families. May be - 'virtex2p', 'virtex4', or 'virtex5'. - - vi) Xilinx Uart 16550 - - Xilinx UART 16550 devices are very similar to the NS16550 but with - different register spacing and an offset from the base address. - - Required properties: - - clock-frequency : Frequency of the clock input - - reg-offset : A value of 3 is required - - reg-shift : A value of 2 is required - - e) USB EHCI controllers - - Required properties: - - compatible : should be "usb-ehci". - - reg : should contain at least address and length of the standard EHCI - register set for the device. Optional platform-dependent registers - (debug-port or other) can be also specified here, but only after - definition of standard EHCI registers. - - interrupts : one EHCI interrupt should be described here. - If device registers are implemented in big endian mode, the device - node should have "big-endian-regs" property. - If controller implementation operates with big endian descriptors, - "big-endian-desc" property should be specified. - If both big endian registers and descriptors are used by the controller - implementation, "big-endian" property can be specified instead of having - both "big-endian-regs" and "big-endian-desc". - - Example (Sequoia 440EPx): - ehci@e0000300 { - compatible = "ibm,usb-ehci-440epx", "usb-ehci"; - interrupt-parent = <&UIC0>; - interrupts = <1a 4>; - reg = <0 e0000300 90 0 e0000390 70>; - big-endian; - }; - - f) MDIO on GPIOs - - Currently defined compatibles: - - virtual,gpio-mdio - - MDC and MDIO lines connected to GPIO controllers are listed in the - gpios property as described in section VIII.1 in the following order: - - MDC, MDIO. - - Example: - - mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qe_pio_a 11 - &qe_pio_c 6>; - }; - - g) SPI (Serial Peripheral Interface) busses - - SPI busses can be described with a node for the SPI master device - and a set of child nodes for each SPI slave on the bus. For this - discussion, it is assumed that the system's SPI controller is in - SPI master mode. This binding does not describe SPI controllers - in slave mode. - - The SPI master node requires the following properties: - - #address-cells - number of cells required to define a chip select - address on the SPI bus. - - #size-cells - should be zero. - - compatible - name of SPI bus controller following generic names - recommended practice. - No other properties are required in the SPI bus node. It is assumed - that a driver for an SPI bus device will understand that it is an SPI bus. - However, the binding does not attempt to define the specific method for - assigning chip select numbers. Since SPI chip select configuration is - flexible and non-standardized, it is left out of this binding with the - assumption that board specific platform code will be used to manage - chip selects. Individual drivers can define additional properties to - support describing the chip select layout. - - SPI slave nodes must be children of the SPI master node and can - contain the following properties. - - reg - (required) chip select address of device. - - compatible - (required) name of SPI device following generic names - recommended practice - - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz - - spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode - - spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode - - spi-cs-high - (optional) Empty property indicating device requires - chip select active high - - SPI example for an MPC5200 SPI bus: - spi@f00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - interrupt-parent = <&mpc5200_pic>; - - ethernet-switch@0 { - compatible = "micrel,ks8995m"; - spi-max-frequency = <1000000>; - reg = <0>; - }; - - codec@1 { - compatible = "ti,tlv320aic26"; - spi-max-frequency = <100000>; - reg = <1>; - }; - }; - -VII - Marvell Discovery mv64[345]6x System Controller chips -=========================================================== - -The Marvell mv64[345]60 series of system controller chips contain -many of the peripherals needed to implement a complete computer -system. In this section, we define device tree nodes to describe -the system controller chip itself and each of the peripherals -which it contains. Compatible string values for each node are -prefixed with the string "marvell,", for Marvell Technology Group Ltd. - -1) The /system-controller node - - This node is used to represent the system-controller and must be - present when the system uses a system controller chip. The top-level - system-controller node contains information that is global to all - devices within the system controller chip. The node name begins - with "system-controller" followed by the unit address, which is - the base address of the memory-mapped register set for the system - controller chip. - - Required properties: - - - ranges : Describes the translation of system controller addresses - for memory mapped registers. - - clock-frequency: Contains the main clock frequency for the system - controller chip. - - reg : This property defines the address and size of the - memory-mapped registers contained within the system controller - chip. The address specified in the "reg" property should match - the unit address of the system-controller node. - - #address-cells : Address representation for system controller - devices. This field represents the number of cells needed to - represent the address of the memory-mapped registers of devices - within the system controller chip. - - #size-cells : Size representation for for the memory-mapped - registers within the system controller chip. - - #interrupt-cells : Defines the width of cells used to represent - interrupts. - - Optional properties: - - - model : The specific model of the system controller chip. Such - as, "mv64360", "mv64460", or "mv64560". - - compatible : A string identifying the compatibility identifiers - of the system controller chip. - - The system-controller node contains child nodes for each system - controller device that the platform uses. Nodes should not be created - for devices which exist on the system controller chip but are not used - - Example Marvell Discovery mv64360 system-controller node: - - system-controller@f1000000 { /* Marvell Discovery mv64360 */ - #address-cells = <1>; - #size-cells = <1>; - model = "mv64360"; /* Default */ - compatible = "marvell,mv64360"; - clock-frequency = <133333333>; - reg = <0xf1000000 0x10000>; - virtual-reg = <0xf1000000>; - ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ - 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ - 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ - 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ - 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ - - [ child node definitions... ] - } - -2) Child nodes of /system-controller - - a) Marvell Discovery MDIO bus - - The MDIO is a bus to which the PHY devices are connected. For each - device that exists on this bus, a child node should be created. See - the definition of the PHY node below for an example of how to define - a PHY. - - Required properties: - - #address-cells : Should be <1> - - #size-cells : Should be <0> - - device_type : Should be "mdio" - - compatible : Should be "marvell,mv64360-mdio" - - Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - device_type = "mdio"; - compatible = "marvell,mv64360-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - - - b) Marvell Discovery ethernet controller - - The Discover ethernet controller is described with two levels - of nodes. The first level describes an ethernet silicon block - and the second level describes up to 3 ethernet nodes within - that block. The reason for the multiple levels is that the - registers for the node are interleaved within a single set - of registers. The "ethernet-block" level describes the - shared register set, and the "ethernet" nodes describe ethernet - port-specific properties. - - Ethernet block node - - Required properties: - - #address-cells : <1> - - #size-cells : <0> - - compatible : "marvell,mv64360-eth-block" - - reg : Offset and length of the register set for this block - - Example Discovery Ethernet block node: - ethernet-block@2000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "marvell,mv64360-eth-block"; - reg = <0x2000 0x2000>; - ethernet@0 { - ....... - }; - }; - - Ethernet port node - - Required properties: - - device_type : Should be "network". - - compatible : Should be "marvell,mv64360-eth". - - reg : Should be <0>, <1>, or <2>, according to which registers - within the silicon block the device uses. - - interrupts : <a> where a is the interrupt number for the port. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - phy : the phandle for the PHY connected to this ethernet - controller. - - local-mac-address : 6 bytes, MAC address - - Example Discovery Ethernet port node: - ethernet@0 { - device_type = "network"; - compatible = "marvell,mv64360-eth"; - reg = <0>; - interrupts = <32>; - interrupt-parent = <&PIC>; - phy = <&PHY0>; - local-mac-address = [ 00 00 00 00 00 00 ]; - }; - - - - c) Marvell Discovery PHY nodes - - Required properties: - - device_type : Should be "ethernet-phy" - - interrupts : <a> where a is the interrupt number for this phy. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - Example Discovery PHY node: - ethernet-phy@1 { - device_type = "ethernet-phy"; - compatible = "broadcom,bcm5421"; - interrupts = <76>; /* GPP 12 */ - interrupt-parent = <&PIC>; - reg = <1>; - }; - - - d) Marvell Discovery SDMA nodes - - Represent DMA hardware associated with the MPSC (multiprotocol - serial controllers). - - Required properties: - - compatible : "marvell,mv64360-sdma" - - reg : Offset and length of the register set for this device - - interrupts : <a> where a is the interrupt number for the DMA - device. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SDMA node: - sdma@4000 { - compatible = "marvell,mv64360-sdma"; - reg = <0x4000 0xc18>; - virtual-reg = <0xf1004000>; - interrupts = <36>; - interrupt-parent = <&PIC>; - }; - - - e) Marvell Discovery BRG nodes - - Represent baud rate generator hardware associated with the MPSC - (multiprotocol serial controllers). - - Required properties: - - compatible : "marvell,mv64360-brg" - - reg : Offset and length of the register set for this device - - clock-src : A value from 0 to 15 which selects the clock - source for the baud rate generator. This value corresponds - to the CLKS value in the BRGx configuration register. See - the mv64x60 User's Manual. - - clock-frequence : The frequency (in Hz) of the baud rate - generator's input clock. - - current-speed : The current speed setting (presumably by - firmware) of the baud rate generator. - - Example Discovery BRG node: - brg@b200 { - compatible = "marvell,mv64360-brg"; - reg = <0xb200 0x8>; - clock-src = <8>; - clock-frequency = <133333333>; - current-speed = <9600>; - }; - - - f) Marvell Discovery CUNIT nodes - - Represent the Serial Communications Unit device hardware. - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - cunit@f200 { - reg = <0xf200 0x200>; - }; - - - g) Marvell Discovery MPSCROUTING nodes - - Represent the Discovery's MPSC routing hardware - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - mpscrouting@b500 { - reg = <0xb400 0xc>; - }; - - - h) Marvell Discovery MPSCINTR nodes - - Represent the Discovery's MPSC DMA interrupt hardware registers - (SDMA cause and mask registers). - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery MPSCINTR node: - mpsintr@b800 { - reg = <0xb800 0x100>; - }; - - - i) Marvell Discovery MPSC nodes - - Represent the Discovery's MPSC (Multiprotocol Serial Controller) - serial port. - - Required properties: - - device_type : "serial" - - compatible : "marvell,mv64360-mpsc" - - reg : Offset and length of the register set for this device - - sdma : the phandle for the SDMA node used by this port - - brg : the phandle for the BRG node used by this port - - cunit : the phandle for the CUNIT node used by this port - - mpscrouting : the phandle for the MPSCROUTING node used by this port - - mpscintr : the phandle for the MPSCINTR node used by this port - - cell-index : the hardware index of this cell in the MPSC core - - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) - register - - interrupts : <a> where a is the interrupt number for the MPSC. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery MPSCINTR node: - mpsc@8000 { - device_type = "serial"; - compatible = "marvell,mv64360-mpsc"; - reg = <0x8000 0x38>; - virtual-reg = <0xf1008000>; - sdma = <&SDMA0>; - brg = <&BRG0>; - cunit = <&CUNIT>; - mpscrouting = <&MPSCROUTING>; - mpscintr = <&MPSCINTR>; - cell-index = <0>; - max_idle = <40>; - interrupts = <40>; - interrupt-parent = <&PIC>; - }; - - - j) Marvell Discovery Watch Dog Timer nodes - - Represent the Discovery's watchdog timer hardware - - Required properties: - - compatible : "marvell,mv64360-wdt" - - reg : Offset and length of the register set for this device - - Example Discovery Watch Dog Timer node: - wdt@b410 { - compatible = "marvell,mv64360-wdt"; - reg = <0xb410 0x8>; - }; - - - k) Marvell Discovery I2C nodes - - Represent the Discovery's I2C hardware - - Required properties: - - device_type : "i2c" - - compatible : "marvell,mv64360-i2c" - - reg : Offset and length of the register set for this device - - interrupts : <a> where a is the interrupt number for the I2C. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery I2C node: - compatible = "marvell,mv64360-i2c"; - reg = <0xc000 0x20>; - virtual-reg = <0xf100c000>; - interrupts = <37>; - interrupt-parent = <&PIC>; - }; - - - l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes - - Represent the Discovery's PIC hardware - - Required properties: - - #interrupt-cells : <1> - - #address-cells : <0> - - compatible : "marvell,mv64360-pic" - - reg : Offset and length of the register set for this device - - interrupt-controller - - Example Discovery PIC node: - pic { - #interrupt-cells = <1>; - #address-cells = <0>; - compatible = "marvell,mv64360-pic"; - reg = <0x0 0x88>; - interrupt-controller; - }; - - - m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes - - Represent the Discovery's MPP hardware - - Required properties: - - compatible : "marvell,mv64360-mpp" - - reg : Offset and length of the register set for this device - - Example Discovery MPP node: - mpp@f000 { - compatible = "marvell,mv64360-mpp"; - reg = <0xf000 0x10>; - }; - - - n) Marvell Discovery GPP (General Purpose Pins) nodes - - Represent the Discovery's GPP hardware - - Required properties: - - compatible : "marvell,mv64360-gpp" - - reg : Offset and length of the register set for this device - - Example Discovery GPP node: - gpp@f000 { - compatible = "marvell,mv64360-gpp"; - reg = <0xf100 0x20>; - }; - - - o) Marvell Discovery PCI host bridge node - - Represents the Discovery's PCI host bridge device. The properties - for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE - 1275-1994. A typical value for the compatible property is - "marvell,mv64360-pci". - - Example Discovery PCI host bridge node - pci@80000000 { - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - device_type = "pci"; - compatible = "marvell,mv64360-pci"; - reg = <0xcf8 0x8>; - ranges = <0x01000000 0x0 0x0 - 0x88000000 0x0 0x01000000 - 0x02000000 0x0 0x80000000 - 0x80000000 0x0 0x08000000>; - bus-range = <0 255>; - clock-frequency = <66000000>; - interrupt-parent = <&PIC>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = < - /* IDSEL 0x0a */ - 0x5000 0 0 1 &PIC 80 - 0x5000 0 0 2 &PIC 81 - 0x5000 0 0 3 &PIC 91 - 0x5000 0 0 4 &PIC 93 - - /* IDSEL 0x0b */ - 0x5800 0 0 1 &PIC 91 - 0x5800 0 0 2 &PIC 93 - 0x5800 0 0 3 &PIC 80 - 0x5800 0 0 4 &PIC 81 - - /* IDSEL 0x0c */ - 0x6000 0 0 1 &PIC 91 - 0x6000 0 0 2 &PIC 93 - 0x6000 0 0 3 &PIC 80 - 0x6000 0 0 4 &PIC 81 - - /* IDSEL 0x0d */ - 0x6800 0 0 1 &PIC 93 - 0x6800 0 0 2 &PIC 80 - 0x6800 0 0 3 &PIC 81 - 0x6800 0 0 4 &PIC 91 - >; - }; - - - p) Marvell Discovery CPU Error nodes - - Represent the Discovery's CPU error handler device. - - Required properties: - - compatible : "marvell,mv64360-cpu-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery CPU Error node: - cpu-error@0070 { - compatible = "marvell,mv64360-cpu-error"; - reg = <0x70 0x10 0x128 0x28>; - interrupts = <3>; - interrupt-parent = <&PIC>; - }; - - - q) Marvell Discovery SRAM Controller nodes - - Represent the Discovery's SRAM controller device. - - Required properties: - - compatible : "marvell,mv64360-sram-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SRAM Controller node: - sram-ctrl@0380 { - compatible = "marvell,mv64360-sram-ctrl"; - reg = <0x380 0x80>; - interrupts = <13>; - interrupt-parent = <&PIC>; - }; - - - r) Marvell Discovery PCI Error Handler nodes - - Represent the Discovery's PCI error handler device. - - Required properties: - - compatible : "marvell,mv64360-pci-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery PCI Error Handler node: - pci-error@1d40 { - compatible = "marvell,mv64360-pci-error"; - reg = <0x1d40 0x40 0xc28 0x4>; - interrupts = <12>; - interrupt-parent = <&PIC>; - }; - - - s) Marvell Discovery Memory Controller nodes - - Represent the Discovery's memory controller device. - - Required properties: - - compatible : "marvell,mv64360-mem-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery Memory Controller node: - mem-ctrl@1400 { - compatible = "marvell,mv64360-mem-ctrl"; - reg = <0x1400 0x60>; - interrupts = <17>; - interrupt-parent = <&PIC>; - }; - - -VIII - Specifying interrupt information for devices +VII - Specifying interrupt information for devices =================================================== The device tree represents the busses and devices of a hardware @@ -2439,56 +1324,7 @@ encodings listed below: 2 = high to low edge sensitive type enabled 3 = low to high edge sensitive type enabled -IX - Specifying GPIO information for devices -============================================ - -1) gpios property ------------------ - -Nodes that makes use of GPIOs should define them using `gpios' property, -format of which is: <&gpio-controller1-phandle gpio1-specifier - &gpio-controller2-phandle gpio2-specifier - 0 /* holes are permitted, means no GPIO 3 */ - &gpio-controller4-phandle gpio4-specifier - ...>; - -Note that gpio-specifier length is controller dependent. - -gpio-specifier may encode: bank, pin position inside the bank, -whether pin is open-drain and whether pin is logically inverted. - -Example of the node using GPIOs: - - node { - gpios = <&qe_pio_e 18 0>; - }; - -In this example gpio-specifier is "18 0" and encodes GPIO pin number, -and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. - -2) gpio-controller nodes ------------------------- - -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -Example of two SOC GPIO banks defined as gpio-controller nodes: - - qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; - compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; - reg = <0x1400 0x18>; - gpio-controller; - }; - - qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; - compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; - reg = <0x1460 0x18>; - gpio-controller; - }; - -X - Specifying Device Power Management Information (sleep property) +VIII - Specifying Device Power Management Information (sleep property) =================================================================== Devices on SOCs often have mechanisms for placing devices into low-power diff --git a/Documentation/powerpc/dts-bindings/4xx/emac.txt b/Documentation/powerpc/dts-bindings/4xx/emac.txt new file mode 100644 index 000000000000..2161334a7ca5 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/4xx/emac.txt @@ -0,0 +1,148 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a ths + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + - reg : <registers mapping> + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + + Example: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : <interrupt mapping for the MAL interrupts sources: + 5 sources: tx_eob, rx_eob, serr, txde, rxde>. + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : <registers mapping> + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : <registers mapping> + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a + diff --git a/Documentation/powerpc/dts-bindings/gpio/gpio.txt b/Documentation/powerpc/dts-bindings/gpio/gpio.txt new file mode 100644 index 000000000000..edaa84d288a1 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/gpio/gpio.txt @@ -0,0 +1,50 @@ +Specifying GPIO information for devices +============================================ + +1) gpios property +----------------- + +Nodes that makes use of GPIOs should define them using `gpios' property, +format of which is: <&gpio-controller1-phandle gpio1-specifier + &gpio-controller2-phandle gpio2-specifier + 0 /* holes are permitted, means no GPIO 3 */ + &gpio-controller4-phandle gpio4-specifier + ...>; + +Note that gpio-specifier length is controller dependent. + +gpio-specifier may encode: bank, pin position inside the bank, +whether pin is open-drain and whether pin is logically inverted. + +Example of the node using GPIOs: + + node { + gpios = <&qe_pio_e 18 0>; + }; + +In this example gpio-specifier is "18 0" and encodes GPIO pin number, +and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +2) gpio-controller nodes +------------------------ + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +Example of two SOC GPIO banks defined as gpio-controller nodes: + + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; + + diff --git a/Documentation/powerpc/dts-bindings/gpio/mdio.txt b/Documentation/powerpc/dts-bindings/gpio/mdio.txt new file mode 100644 index 000000000000..bc9549529014 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/gpio/mdio.txt @@ -0,0 +1,19 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Example: + +mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/powerpc/dts-bindings/marvell.txt b/Documentation/powerpc/dts-bindings/marvell.txt new file mode 100644 index 000000000000..3708a2fd4747 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/marvell.txt @@ -0,0 +1,521 @@ +Marvell Discovery mv64[345]6x System Controller chips +=========================================================== + +The Marvell mv64[345]60 series of system controller chips contain +many of the peripherals needed to implement a complete computer +system. In this section, we define device tree nodes to describe +the system controller chip itself and each of the peripherals +which it contains. Compatible string values for each node are +prefixed with the string "marvell,", for Marvell Technology Group Ltd. + +1) The /system-controller node + + This node is used to represent the system-controller and must be + present when the system uses a system controller chip. The top-level + system-controller node contains information that is global to all + devices within the system controller chip. The node name begins + with "system-controller" followed by the unit address, which is + the base address of the memory-mapped register set for the system + controller chip. + + Required properties: + + - ranges : Describes the translation of system controller addresses + for memory mapped registers. + - clock-frequency: Contains the main clock frequency for the system + controller chip. + - reg : This property defines the address and size of the + memory-mapped registers contained within the system controller + chip. The address specified in the "reg" property should match + the unit address of the system-controller node. + - #address-cells : Address representation for system controller + devices. This field represents the number of cells needed to + represent the address of the memory-mapped registers of devices + within the system controller chip. + - #size-cells : Size representation for for the memory-mapped + registers within the system controller chip. + - #interrupt-cells : Defines the width of cells used to represent + interrupts. + + Optional properties: + + - model : The specific model of the system controller chip. Such + as, "mv64360", "mv64460", or "mv64560". + - compatible : A string identifying the compatibility identifiers + of the system controller chip. + + The system-controller node contains child nodes for each system + controller device that the platform uses. Nodes should not be created + for devices which exist on the system controller chip but are not used + + Example Marvell Discovery mv64360 system-controller node: + + system-controller@f1000000 { /* Marvell Discovery mv64360 */ + #address-cells = <1>; + #size-cells = <1>; + model = "mv64360"; /* Default */ + compatible = "marvell,mv64360"; + clock-frequency = <133333333>; + reg = <0xf1000000 0x10000>; + virtual-reg = <0xf1000000>; + ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ + 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ + 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ + 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ + 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ + + [ child node definitions... ] + } + +2) Child nodes of /system-controller + + a) Marvell Discovery MDIO bus + + The MDIO is a bus to which the PHY devices are connected. For each + device that exists on this bus, a child node should be created. See + the definition of the PHY node below for an example of how to define + a PHY. + + Required properties: + - #address-cells : Should be <1> + - #size-cells : Should be <0> + - device_type : Should be "mdio" + - compatible : Should be "marvell,mv64360-mdio" + + Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + device_type = "mdio"; + compatible = "marvell,mv64360-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + + + b) Marvell Discovery ethernet controller + + The Discover ethernet controller is described with two levels + of nodes. The first level describes an ethernet silicon block + and the second level describes up to 3 ethernet nodes within + that block. The reason for the multiple levels is that the + registers for the node are interleaved within a single set + of registers. The "ethernet-block" level describes the + shared register set, and the "ethernet" nodes describe ethernet + port-specific properties. + + Ethernet block node + + Required properties: + - #address-cells : <1> + - #size-cells : <0> + - compatible : "marvell,mv64360-eth-block" + - reg : Offset and length of the register set for this block + + Example Discovery Ethernet block node: + ethernet-block@2000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,mv64360-eth-block"; + reg = <0x2000 0x2000>; + ethernet@0 { + ....... + }; + }; + + Ethernet port node + + Required properties: + - device_type : Should be "network". + - compatible : Should be "marvell,mv64360-eth". + - reg : Should be <0>, <1>, or <2>, according to which registers + within the silicon block the device uses. + - interrupts : <a> where a is the interrupt number for the port. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + - phy : the phandle for the PHY connected to this ethernet + controller. + - local-mac-address : 6 bytes, MAC address + + Example Discovery Ethernet port node: + ethernet@0 { + device_type = "network"; + compatible = "marvell,mv64360-eth"; + reg = <0>; + interrupts = <32>; + interrupt-parent = <&PIC>; + phy = <&PHY0>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + + + c) Marvell Discovery PHY nodes + + Required properties: + - device_type : Should be "ethernet-phy" + - interrupts : <a> where a is the interrupt number for this phy. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + + Example Discovery PHY node: + ethernet-phy@1 { + device_type = "ethernet-phy"; + compatible = "broadcom,bcm5421"; + interrupts = <76>; /* GPP 12 */ + interrupt-parent = <&PIC>; + reg = <1>; + }; + + + d) Marvell Discovery SDMA nodes + + Represent DMA hardware associated with the MPSC (multiprotocol + serial controllers). + + Required properties: + - compatible : "marvell,mv64360-sdma" + - reg : Offset and length of the register set for this device + - interrupts : <a> where a is the interrupt number for the DMA + device. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SDMA node: + sdma@4000 { + compatible = "marvell,mv64360-sdma"; + reg = <0x4000 0xc18>; + virtual-reg = <0xf1004000>; + interrupts = <36>; + interrupt-parent = <&PIC>; + }; + + + e) Marvell Discovery BRG nodes + + Represent baud rate generator hardware associated with the MPSC + (multiprotocol serial controllers). + + Required properties: + - compatible : "marvell,mv64360-brg" + - reg : Offset and length of the register set for this device + - clock-src : A value from 0 to 15 which selects the clock + source for the baud rate generator. This value corresponds + to the CLKS value in the BRGx configuration register. See + the mv64x60 User's Manual. + - clock-frequence : The frequency (in Hz) of the baud rate + generator's input clock. + - current-speed : The current speed setting (presumably by + firmware) of the baud rate generator. + + Example Discovery BRG node: + brg@b200 { + compatible = "marvell,mv64360-brg"; + reg = <0xb200 0x8>; + clock-src = <8>; + clock-frequency = <133333333>; + current-speed = <9600>; + }; + + + f) Marvell Discovery CUNIT nodes + + Represent the Serial Communications Unit device hardware. + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + cunit@f200 { + reg = <0xf200 0x200>; + }; + + + g) Marvell Discovery MPSCROUTING nodes + + Represent the Discovery's MPSC routing hardware + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery CUNIT node: + mpscrouting@b500 { + reg = <0xb400 0xc>; + }; + + + h) Marvell Discovery MPSCINTR nodes + + Represent the Discovery's MPSC DMA interrupt hardware registers + (SDMA cause and mask registers). + + Required properties: + - reg : Offset and length of the register set for this device + + Example Discovery MPSCINTR node: + mpsintr@b800 { + reg = <0xb800 0x100>; + }; + + + i) Marvell Discovery MPSC nodes + + Represent the Discovery's MPSC (Multiprotocol Serial Controller) + serial port. + + Required properties: + - device_type : "serial" + - compatible : "marvell,mv64360-mpsc" + - reg : Offset and length of the register set for this device + - sdma : the phandle for the SDMA node used by this port + - brg : the phandle for the BRG node used by this port + - cunit : the phandle for the CUNIT node used by this port + - mpscrouting : the phandle for the MPSCROUTING node used by this port + - mpscintr : the phandle for the MPSCINTR node used by this port + - cell-index : the hardware index of this cell in the MPSC core + - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) + register + - interrupts : <a> where a is the interrupt number for the MPSC. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery MPSCINTR node: + mpsc@8000 { + device_type = "serial"; + compatible = "marvell,mv64360-mpsc"; + reg = <0x8000 0x38>; + virtual-reg = <0xf1008000>; + sdma = <&SDMA0>; + brg = <&BRG0>; + cunit = <&CUNIT>; + mpscrouting = <&MPSCROUTING>; + mpscintr = <&MPSCINTR>; + cell-index = <0>; + max_idle = <40>; + interrupts = <40>; + interrupt-parent = <&PIC>; + }; + + + j) Marvell Discovery Watch Dog Timer nodes + + Represent the Discovery's watchdog timer hardware + + Required properties: + - compatible : "marvell,mv64360-wdt" + - reg : Offset and length of the register set for this device + + Example Discovery Watch Dog Timer node: + wdt@b410 { + compatible = "marvell,mv64360-wdt"; + reg = <0xb410 0x8>; + }; + + + k) Marvell Discovery I2C nodes + + Represent the Discovery's I2C hardware + + Required properties: + - device_type : "i2c" + - compatible : "marvell,mv64360-i2c" + - reg : Offset and length of the register set for this device + - interrupts : <a> where a is the interrupt number for the I2C. + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery I2C node: + compatible = "marvell,mv64360-i2c"; + reg = <0xc000 0x20>; + virtual-reg = <0xf100c000>; + interrupts = <37>; + interrupt-parent = <&PIC>; + }; + + + l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes + + Represent the Discovery's PIC hardware + + Required properties: + - #interrupt-cells : <1> + - #address-cells : <0> + - compatible : "marvell,mv64360-pic" + - reg : Offset and length of the register set for this device + - interrupt-controller + + Example Discovery PIC node: + pic { + #interrupt-cells = <1>; + #address-cells = <0>; + compatible = "marvell,mv64360-pic"; + reg = <0x0 0x88>; + interrupt-controller; + }; + + + m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes + + Represent the Discovery's MPP hardware + + Required properties: + - compatible : "marvell,mv64360-mpp" + - reg : Offset and length of the register set for this device + + Example Discovery MPP node: + mpp@f000 { + compatible = "marvell,mv64360-mpp"; + reg = <0xf000 0x10>; + }; + + + n) Marvell Discovery GPP (General Purpose Pins) nodes + + Represent the Discovery's GPP hardware + + Required properties: + - compatible : "marvell,mv64360-gpp" + - reg : Offset and length of the register set for this device + + Example Discovery GPP node: + gpp@f000 { + compatible = "marvell,mv64360-gpp"; + reg = <0xf100 0x20>; + }; + + + o) Marvell Discovery PCI host bridge node + + Represents the Discovery's PCI host bridge device. The properties + for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE + 1275-1994. A typical value for the compatible property is + "marvell,mv64360-pci". + + Example Discovery PCI host bridge node + pci@80000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + compatible = "marvell,mv64360-pci"; + reg = <0xcf8 0x8>; + ranges = <0x01000000 0x0 0x0 + 0x88000000 0x0 0x01000000 + 0x02000000 0x0 0x80000000 + 0x80000000 0x0 0x08000000>; + bus-range = <0 255>; + clock-frequency = <66000000>; + interrupt-parent = <&PIC>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0a */ + 0x5000 0 0 1 &PIC 80 + 0x5000 0 0 2 &PIC 81 + 0x5000 0 0 3 &PIC 91 + 0x5000 0 0 4 &PIC 93 + + /* IDSEL 0x0b */ + 0x5800 0 0 1 &PIC 91 + 0x5800 0 0 2 &PIC 93 + 0x5800 0 0 3 &PIC 80 + 0x5800 0 0 4 &PIC 81 + + /* IDSEL 0x0c */ + 0x6000 0 0 1 &PIC 91 + 0x6000 0 0 2 &PIC 93 + 0x6000 0 0 3 &PIC 80 + 0x6000 0 0 4 &PIC 81 + + /* IDSEL 0x0d */ + 0x6800 0 0 1 &PIC 93 + 0x6800 0 0 2 &PIC 80 + 0x6800 0 0 3 &PIC 81 + 0x6800 0 0 4 &PIC 91 + >; + }; + + + p) Marvell Discovery CPU Error nodes + + Represent the Discovery's CPU error handler device. + + Required properties: + - compatible : "marvell,mv64360-cpu-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery CPU Error node: + cpu-error@0070 { + compatible = "marvell,mv64360-cpu-error"; + reg = <0x70 0x10 0x128 0x28>; + interrupts = <3>; + interrupt-parent = <&PIC>; + }; + + + q) Marvell Discovery SRAM Controller nodes + + Represent the Discovery's SRAM controller device. + + Required properties: + - compatible : "marvell,mv64360-sram-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery SRAM Controller node: + sram-ctrl@0380 { + compatible = "marvell,mv64360-sram-ctrl"; + reg = <0x380 0x80>; + interrupts = <13>; + interrupt-parent = <&PIC>; + }; + + + r) Marvell Discovery PCI Error Handler nodes + + Represent the Discovery's PCI error handler device. + + Required properties: + - compatible : "marvell,mv64360-pci-error" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery PCI Error Handler node: + pci-error@1d40 { + compatible = "marvell,mv64360-pci-error"; + reg = <0x1d40 0x40 0xc28 0x4>; + interrupts = <12>; + interrupt-parent = <&PIC>; + }; + + + s) Marvell Discovery Memory Controller nodes + + Represent the Discovery's memory controller device. + + Required properties: + - compatible : "marvell,mv64360-mem-ctrl" + - reg : Offset and length of the register set for this device + - interrupts : the interrupt number for this device + - interrupt-parent : the phandle for the interrupt controller + that services interrupts for this device. + + Example Discovery Memory Controller node: + mem-ctrl@1400 { + compatible = "marvell,mv64360-mem-ctrl"; + reg = <0x1400 0x60>; + interrupts = <17>; + interrupt-parent = <&PIC>; + }; + + diff --git a/Documentation/powerpc/dts-bindings/phy.txt b/Documentation/powerpc/dts-bindings/phy.txt new file mode 100644 index 000000000000..bb8c742eb8c5 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/phy.txt @@ -0,0 +1,25 @@ +PHY nodes + +Required properties: + + - device_type : Should be "ethernet-phy" + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + - linux,phandle : phandle for this node; likely referenced by an + ethernet controller node. + +Example: + +ethernet-phy@0 { + linux,phandle = <2452000> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; + device_type = "ethernet-phy"; +}; diff --git a/Documentation/powerpc/dts-bindings/spi-bus.txt b/Documentation/powerpc/dts-bindings/spi-bus.txt new file mode 100644 index 000000000000..e782add2e457 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/spi-bus.txt @@ -0,0 +1,57 @@ +SPI (Serial Peripheral Interface) busses + +SPI busses can be described with a node for the SPI master device +and a set of child nodes for each SPI slave on the bus. For this +discussion, it is assumed that the system's SPI controller is in +SPI master mode. This binding does not describe SPI controllers +in slave mode. + +The SPI master node requires the following properties: +- #address-cells - number of cells required to define a chip select + address on the SPI bus. +- #size-cells - should be zero. +- compatible - name of SPI bus controller following generic names + recommended practice. +No other properties are required in the SPI bus node. It is assumed +that a driver for an SPI bus device will understand that it is an SPI bus. +However, the binding does not attempt to define the specific method for +assigning chip select numbers. Since SPI chip select configuration is +flexible and non-standardized, it is left out of this binding with the +assumption that board specific platform code will be used to manage +chip selects. Individual drivers can define additional properties to +support describing the chip select layout. + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. +- reg - (required) chip select address of device. +- compatible - (required) name of SPI device following generic names + recommended practice +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz +- spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode +- spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode +- spi-cs-high - (optional) Empty property indicating device requires + chip select active high + +SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/powerpc/dts-bindings/usb-ehci.txt b/Documentation/powerpc/dts-bindings/usb-ehci.txt new file mode 100644 index 000000000000..fa18612f757b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/usb-ehci.txt @@ -0,0 +1,25 @@ +USB EHCI controllers + +Required properties: + - compatible : should be "usb-ehci". + - reg : should contain at least address and length of the standard EHCI + register set for the device. Optional platform-dependent registers + (debug-port or other) can be also specified here, but only after + definition of standard EHCI registers. + - interrupts : one EHCI interrupt should be described here. +If device registers are implemented in big endian mode, the device +node should have "big-endian-regs" property. +If controller implementation operates with big endian descriptors, +"big-endian-desc" property should be specified. +If both big endian registers and descriptors are used by the controller +implementation, "big-endian" property can be specified instead of having +both "big-endian-regs" and "big-endian-desc". + +Example (Sequoia 440EPx): + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "usb-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <1a 4>; + reg = <0 e0000300 90 0 e0000390 70>; + big-endian; + }; diff --git a/Documentation/powerpc/dts-bindings/xilinx.txt b/Documentation/powerpc/dts-bindings/xilinx.txt new file mode 100644 index 000000000000..80339fe4300b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/xilinx.txt @@ -0,0 +1,295 @@ + d) Xilinx IP cores + + The Xilinx EDK toolchain ships with a set of IP cores (devices) for use + in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range + of standard device types (network, serial, etc.) and miscellaneous + devices (gpio, LCD, spi, etc). Also, since these devices are + implemented within the fpga fabric every instance of the device can be + synthesised with different options that change the behaviour. + + Each IP-core has a set of parameters which the FPGA designer can use to + control how the core is synthesized. Historically, the EDK tool would + extract the device parameters relevant to device drivers and copy them + into an 'xparameters.h' in the form of #define symbols. This tells the + device drivers how the IP cores are configured, but it requres the kernel + to be recompiled every time the FPGA bitstream is resynthesized. + + The new approach is to export the parameters into the device tree and + generate a new device tree each time the FPGA bitstream changes. The + parameters which used to be exported as #defines will now become + properties of the device node. In general, device nodes for IP-cores + will take the following form: + + (name): (generic-name)@(base-address) { + compatible = "xlnx,(ip-core-name)-(HW_VER)" + [, (list of compatible devices), ...]; + reg = <(baseaddr) (size)>; + interrupt-parent = <&interrupt-controller-phandle>; + interrupts = < ... >; + xlnx,(parameter1) = "(string-value)"; + xlnx,(parameter2) = <(int-value)>; + }; + + (generic-name): an open firmware-style name that describes the + generic class of device. Preferably, this is one word, such + as 'serial' or 'ethernet'. + (ip-core-name): the name of the ip block (given after the BEGIN + directive in system.mhs). Should be in lowercase + and all underscores '_' converted to dashes '-'. + (name): is derived from the "PARAMETER INSTANCE" value. + (parameter#): C_* parameters from system.mhs. The C_ prefix is + dropped from the parameter name, the name is converted + to lowercase and all underscore '_' characters are + converted to dashes '-'. + (baseaddr): the baseaddr parameter value (often named C_BASEADDR). + (HW_VER): from the HW_VER parameter. + (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). + + Typically, the compatible list will include the exact IP core version + followed by an older IP core version which implements the same + interface or any other device with the same interface. + + 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. + + For example, the following block from system.mhs: + + BEGIN opb_uartlite + PARAMETER INSTANCE = opb_uartlite_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BAUDRATE = 115200 + PARAMETER C_DATA_BITS = 8 + PARAMETER C_ODD_PARITY = 0 + PARAMETER C_USE_PARITY = 0 + PARAMETER C_CLK_FREQ = 50000000 + PARAMETER C_BASEADDR = 0xEC100000 + PARAMETER C_HIGHADDR = 0xEC10FFFF + BUS_INTERFACE SOPB = opb_7 + PORT OPB_Clk = CLK_50MHz + PORT Interrupt = opb_uartlite_0_Interrupt + PORT RX = opb_uartlite_0_RX + PORT TX = opb_uartlite_0_TX + PORT OPB_Rst = sys_bus_reset_0 + END + + becomes the following device tree node: + + opb_uartlite_0: serial@ec100000 { + device_type = "serial"; + compatible = "xlnx,opb-uartlite-1.00.b"; + reg = <ec100000 10000>; + interrupt-parent = <&opb_intc_0>; + interrupts = <1 0>; // got this from the opb_intc parameters + current-speed = <d#115200>; // standard serial device prop + clock-frequency = <d#50000000>; // standard serial device prop + xlnx,data-bits = <8>; + xlnx,odd-parity = <0>; + xlnx,use-parity = <0>; + }; + + Some IP cores actually implement 2 or more logical devices. In + this case, the device should still describe the whole IP core with + a single node and add a child node for each logical device. The + ranges property can be used to translate from parent IP-core to the + registers of each device. In addition, the parent node should be + compatible with the bus type 'xlnx,compound', and should contain + #address-cells and #size-cells, as with any other bus. (Note: this + makes the assumption that both logical devices have the same bus + binding. If this is not true, then separate nodes should be used + for each logical device). The 'cell-index' property can be used to + enumerate logical devices within an IP core. For example, the + following is the system.mhs entry for the dual ps2 controller found + on the ml403 reference design. + + BEGIN opb_ps2_dual_ref + PARAMETER INSTANCE = opb_ps2_dual_ref_0 + PARAMETER HW_VER = 1.00.a + PARAMETER C_BASEADDR = 0xA9000000 + PARAMETER C_HIGHADDR = 0xA9001FFF + BUS_INTERFACE SOPB = opb_v20_0 + PORT Sys_Intr1 = ps2_1_intr + PORT Sys_Intr2 = ps2_2_intr + PORT Clkin1 = ps2_clk_rx_1 + PORT Clkin2 = ps2_clk_rx_2 + PORT Clkpd1 = ps2_clk_tx_1 + PORT Clkpd2 = ps2_clk_tx_2 + PORT Rx1 = ps2_d_rx_1 + PORT Rx2 = ps2_d_rx_2 + PORT Txpd1 = ps2_d_tx_1 + PORT Txpd2 = ps2_d_tx_2 + END + + It would result in the following device tree nodes: + + opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,compound"; + ranges = <0 a9000000 2000>; + // If this device had extra parameters, then they would + // go here. + ps2@0 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <0 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + ps2@1000 { + compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; + reg = <1000 40>; + interrupt-parent = <&opb_intc_0>; + interrupts = <3 0>; + cell-index = <0>; + }; + }; + + Also, the system.mhs file defines bus attachments from the processor + to the devices. The device tree structure should reflect the bus + attachments. Again an example; this system.mhs fragment: + + BEGIN ppc405_virtex4 + PARAMETER INSTANCE = ppc405_0 + PARAMETER HW_VER = 1.01.a + BUS_INTERFACE DPLB = plb_v34_0 + BUS_INTERFACE IPLB = plb_v34_0 + END + + BEGIN opb_intc + PARAMETER INSTANCE = opb_intc_0 + PARAMETER HW_VER = 1.00.c + PARAMETER C_BASEADDR = 0xD1000FC0 + PARAMETER C_HIGHADDR = 0xD1000FDF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN opb_uart16550 + PARAMETER INSTANCE = opb_uart16550_0 + PARAMETER HW_VER = 1.00.d + PARAMETER C_BASEADDR = 0xa0000000 + PARAMETER C_HIGHADDR = 0xa0001FFF + BUS_INTERFACE SOPB = opb_v20_0 + END + + BEGIN plb_v34 + PARAMETER INSTANCE = plb_v34_0 + PARAMETER HW_VER = 1.02.a + END + + BEGIN plb_bram_if_cntlr + PARAMETER INSTANCE = plb_bram_if_cntlr_0 + PARAMETER HW_VER = 1.00.b + PARAMETER C_BASEADDR = 0xFFFF0000 + PARAMETER C_HIGHADDR = 0xFFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + END + + BEGIN plb2opb_bridge + PARAMETER INSTANCE = plb2opb_bridge_0 + PARAMETER HW_VER = 1.01.a + PARAMETER C_RNG0_BASEADDR = 0x20000000 + PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF + PARAMETER C_RNG1_BASEADDR = 0x60000000 + PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF + PARAMETER C_RNG2_BASEADDR = 0x80000000 + PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF + PARAMETER C_RNG3_BASEADDR = 0xC0000000 + PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF + BUS_INTERFACE SPLB = plb_v34_0 + BUS_INTERFACE MOPB = opb_v20_0 + END + + Gives this device tree (some properties removed for clarity): + + plb@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "xlnx,plb-v34-1.02.a"; + device_type = "ibm,plb"; + ranges; // 1:1 translation + + plb_bram_if_cntrl_0: bram@ffff0000 { + reg = <ffff0000 10000>; + } + + opb@20000000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <20000000 20000000 20000000 + 60000000 60000000 20000000 + 80000000 80000000 40000000 + c0000000 c0000000 20000000>; + + opb_uart16550_0: serial@a0000000 { + reg = <a00000000 2000>; + }; + + opb_intc_0: interrupt-controller@d1000fc0 { + reg = <d1000fc0 20>; + }; + }; + }; + + That covers the general approach to binding xilinx IP cores into the + device tree. The following are bindings for specific devices: + + i) Xilinx ML300 Framebuffer + + Simple framebuffer device from the ML300 reference design (also on the + ML403 reference design as well as others). + + Optional properties: + - resolution = <xres yres> : pixel resolution of framebuffer. Some + implementations use a different resolution. + Default is <d#640 d#480> + - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory. + Default is <d#1024 d#480>. + - rotate-display (empty) : rotate display 180 degrees. + + ii) Xilinx SystemACE + + The Xilinx SystemACE device is used to program FPGAs from an FPGA + bitstream stored on a CF card. It can also be used as a generic CF + interface device. + + Optional properties: + - 8-bit (empty) : Set this property for SystemACE in 8 bit mode + + iii) Xilinx EMAC and Xilinx TEMAC + + Xilinx Ethernet devices. In addition to general xilinx properties + listed above, nodes for these devices should include a phy-handle + property, and may include other common network device properties + like local-mac-address. + + iv) Xilinx Uartlite + + Xilinx uartlite devices are simple fixed speed serial ports. + + Required properties: + - current-speed : Baud rate of uartlite + + v) Xilinx hwicap + + Xilinx hwicap devices provide access to the configuration logic + of the FPGA through the Internal Configuration Access Port + (ICAP). The ICAP enables partial reconfiguration of the FPGA, + readback of the configuration information, and some control over + 'warm boots' of the FPGA fabric. + + Required properties: + - xlnx,family : The family of the FPGA, necessary since the + capabilities of the underlying ICAP hardware + differ between different families. May be + 'virtex2p', 'virtex4', or 'virtex5'. + + vi) Xilinx Uart 16550 + + Xilinx UART 16550 devices are very similar to the NS16550 but with + different register spacing and an offset from the base address. + + Required properties: + - clock-frequency : Frequency of the clock input + - reg-offset : A value of 3 is required + - reg-shift : A value of 2 is required + + |