Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 131 insertions, 0 deletions

diff --git a/Documentation/networking/ltpc.txt b/Documentation/networking/ltpc.txt
new file mode 100644
index 000000000000..fe2a9129d959
--- /dev/null
+++ b/Documentation/networking/ltpc.txt
@@ -0,0 +1,131 @@
+This is the ALPHA version of the ltpc driver.
+
+In order to use it, you will need at least version 1.3.3 of the
+netatalk package, and the Apple or Farallon LocalTalk PC card.
+There are a number of different LocalTalk cards for the PC; this
+driver applies only to the one with the 65c02 processor chip on it.
+
+To include it in the kernel, select the CONFIG_LTPC switch in the
+configuration dialog.  You can also compile it as a module.
+
+While the driver will attempt to autoprobe the I/O port address, IRQ
+line, and DMA channel of the card, this does not always work.  For
+this reason, you should be prepared to supply these parameters
+yourself.  (see "Card Configuration" below for how to determine or
+change the settings on your card)
+
+When the driver is compiled into the kernel, you can add a line such
+as the following to your /etc/lilo.conf:
+
+ append="ltpc=0x240,9,1"
+
+where the parameters (in order) are the port address, IRQ, and DMA
+channel.  The second and third values can be omitted, in which case
+the driver will try to determine them itself.
+
+If you load the driver as a module, you can pass the parameters "io=",
+"irq=", and "dma=" on the command line with insmod or modprobe, or add
+them as options in /etc/modprobe.conf:
+
+ alias lt0 ltpc # autoload the module when the interface is configured
+ options ltpc io=0x240 irq=9 dma=1
+
+Before starting up the netatalk demons (perhaps in rc.local), you
+need to add a line such as:
+
+ /sbin/ifconfig lt0 127.0.0.42
+
+The address is unimportant - however, the card needs to be configured
+with ifconfig so that Netatalk can find it.
+
+The appropriate netatalk configuration depends on whether you are
+attached to a network that includes AppleTalk routers or not.  If,
+like me, you are simply connecting to your home Macintoshes and
+printers, you need to set up netatalk to "seed".  The way I do this
+is to have the lines
+
+ dummy -seed -phase 2 -net 2000 -addr 2000.26 -zone "1033"
+ lt0 -seed -phase 1 -net 1033 -addr 1033.27 -zone "1033"
+
+in my atalkd.conf.  What is going on here is that I need to fool
+netatalk into thinking that there are two AppleTalk interfaces
+present; otherwise, it refuses to seed.  This is a hack, and a more
+permanent solution would be to alter the netatalk code.  Also, make
+sure you have the correct name for the dummy interface - If it's
+compiled as a module, you will need to refer to it as "dummy0" or some
+such.
+
+If you are attached to an extended AppleTalk network, with routers on
+it, then you don't need to fool around with this -- the appropriate
+line in atalkd.conf is
+
+ lt0 -phase 1
+
+--------------------------------------
+
+Card Configuration:
+
+The interrupts and so forth are configured via the dipswitch on the
+board.  Set the switches so as not to conflict with other hardware.
+
+       Interrupts -- set at most one.  If none are set, the driver uses
+       polled mode.  Because the card was developed in the XT era, the
+       original documentation refers to IRQ2.  Since you'll be running
+       this on an AT (or later) class machine, that really means IRQ9.
+
+       SW1     IRQ 4
+       SW2     IRQ 3
+       SW3     IRQ 9 (2 in original card documentation only applies to XT)
+
+
+       DMA -- choose DMA 1 or 3, and set both corresponding switches.
+
+       SW4     DMA 3
+       SW5     DMA 1
+       SW6     DMA 3
+       SW7     DMA 1
+
+
+       I/O address -- choose one.
+
+       SW8     220 / 240
+
+--------------------------------------
+
+IP:
+
+Yes, it is possible to do IP over LocalTalk.  However, you can't just
+treat the LocalTalk device like an ordinary Ethernet device, even if
+that's what it looks like to Netatalk.
+
+Instead, you follow the same procedure as for doing IP in EtherTalk.
+See Documentation/networking/ipddp.txt for more information about the
+kernel driver and userspace tools needed.
+
+--------------------------------------
+
+BUGS:
+
+IRQ autoprobing often doesn't work on a cold boot.  To get around
+this, either compile the driver as a module, or pass the parameters
+for the card to the kernel as described above.
+
+Also, as usual, autoprobing is not recommended when you use the driver
+as a module. (though it usually works at boot time, at least)
+
+Polled mode is *really* slow sometimes, but this seems to depend on
+the configuration of the network.
+
+It may theoretically be possible to use two LTPC cards in the same
+machine, but this is unsupported, so if you really want to do this,
+you'll probably have to hack the initialization code a bit.
+
+______________________________________
+
+THANKS:
+	Thanks to Alan Cox for helpful discussions early on in this
+work, and to Denis Hainsworth for doing the bleeding-edge testing.
+
+-- Bradford Johnson <bradford@math.umn.edu>
+
+-- Updated 11/09/1998 by David Huggins-Daines <dhd@debian.org>