docs: hwmon: Add an index file and rename docs to *.rst

Now that all files were converted to ReST format, rename them
and add an index.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

1 files changed, 0 insertions, 197 deletions

diff --git a/Documentation/hwmon/smsc47b397 b/Documentation/hwmon/smsc47b397
deleted file mode 100644
index 600194cf1804..000000000000
--- a/Documentation/hwmon/smsc47b397
+++ /dev/null
@@ -1,197 +0,0 @@
-Kernel driver smsc47b397
-========================
-
-Supported chips:
-
-  * SMSC LPC47B397-NC
-
-  * SMSC SCH5307-NS
-
-  * SMSC SCH5317
-
-    Prefix: 'smsc47b397'
-
-    Addresses scanned: none, address read from Super I/O config space
-
-    Datasheet: In this file
-
-Authors:
-
-       - Mark M. Hoffman <mhoffman@lightlink.com>
-       - Utilitek Systems, Inc.
-
-November 23, 2004
-
-The following specification describes the SMSC LPC47B397-NC [1]_ sensor chip
-(for which there is no public datasheet available). This document was
-provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected
-by Mark M. Hoffman <mhoffman@lightlink.com>.
-
-.. [1] And SMSC SCH5307-NS and SCH5317, which have different device IDs but are
-       otherwise compatible.
-
--------------------------------------------------------------------------
-
-Methods for detecting the HP SIO and reading the thermal data on a dc7100
--------------------------------------------------------------------------
-
-The thermal information on the dc7100 is contained in the SIO Hardware Monitor
-(HWM). The information is accessed through an index/data pair. The index/data
-pair is located at the HWM Base Address + 0 and the HWM Base Address + 1. The
-HWM Base address can be obtained from Logical Device 8, registers 0x60 (MSB)
-and 0x61 (LSB). Currently we are using 0x480 for the HWM Base Address and
-0x480 and 0x481 for the index/data pair.
-
-Reading temperature information.
-The temperature information is located in the following registers:
-
-=============== ======= =======================================================
-Temp1		0x25	(Currently, this reflects the CPU temp on all systems).
-Temp2		0x26
-Temp3		0x27
-Temp4		0x80
-=============== ======= =======================================================
-
-Programming Example
-The following is an example of how to read the HWM temperature registers::
-
-	MOV	DX,480H
-	MOV	AX,25H
-	OUT	DX,AL
-	MOV	DX,481H
-	IN	AL,DX
-
-AL contains the data in hex, the temperature in Celsius is the decimal
-equivalent.
-
-Ex: If AL contains 0x2A, the temperature is 42 degrees C.
-
-Reading tach information.
-The fan speed information is located in the following registers:
-
-=============== ======= ======= =================================
-		LSB	MSB
-Tach1		0x28	0x29	(Currently, this reflects the CPU
-				fan speed on all systems).
-Tach2		0x2A	0x2B
-Tach3		0x2C	0x2D
-Tach4		0x2E	0x2F
-=============== ======= ======= =================================
-
-.. Important::
-
-	Reading the tach LSB locks the tach MSB.
-	The LSB Must be read first.
-
-How to convert the tach reading to RPM
---------------------------------------
-
-The tach reading (TCount) is given by: (Tach MSB * 256) + (Tach LSB)
-The SIO counts the number of 90kHz (11.111us) pulses per revolution.
-RPM = 60/(TCount * 11.111us)
-
-Example::
-
-	Reg 0x28 = 0x9B
-	Reg 0x29 = 0x08
-
-TCount = 0x89B = 2203
-
-RPM = 60 / (2203 * 11.11111 E-6) = 2451 RPM
-
-Obtaining the SIO version.
-
-Configuration Sequence
-----------------------
-
-To program the configuration registers, the following sequence must be followed:
-1. Enter Configuration Mode
-2. Configure the Configuration Registers
-3. Exit Configuration Mode.
-
-Enter Configuration Mode
-^^^^^^^^^^^^^^^^^^^^^^^^
-
-To place the chip into the Configuration State The config key (0x55) is written
-to the CONFIG PORT (0x2E).
-
-Configuration Mode
-^^^^^^^^^^^^^^^^^^
-
-In configuration mode, the INDEX PORT is located at the CONFIG PORT address and
-the DATA PORT is at INDEX PORT address + 1.
-
-The desired configuration registers are accessed in two steps:
-
-a.	Write the index of the Logical Device Number Configuration Register
-	(i.e., 0x07) to the INDEX PORT and then write the number of the
-	desired logical device to the DATA PORT.
-
-b.	Write the address of the desired configuration register within the
-	logical device to the INDEX PORT and then write or read the config-
-	uration register through the DATA PORT.
-
-Note:
-	If accessing the Global Configuration Registers, step (a) is not required.
-
-Exit Configuration Mode
-^^^^^^^^^^^^^^^^^^^^^^^
-
-To exit the Configuration State the write 0xAA to the CONFIG PORT (0x2E).
-The chip returns to the RUN State.  (This is important).
-
-Programming Example
-^^^^^^^^^^^^^^^^^^^
-
-The following is an example of how to read the SIO Device ID located at 0x20:
-
-	; ENTER CONFIGURATION MODE
-	MOV	DX,02EH
-	MOV	AX,055H
-	OUT	DX,AL
-	; GLOBAL CONFIGURATION  REGISTER
-	MOV	DX,02EH
-	MOV	AL,20H
-	OUT	DX,AL
-	; READ THE DATA
-	MOV	DX,02FH
-	IN	AL,DX
-	; EXIT CONFIGURATION MODE
-	MOV	DX,02EH
-	MOV	AX,0AAH
-	OUT	DX,AL
-
-The registers of interest for identifying the SIO on the dc7100 are Device ID
-(0x20) and Device Rev  (0x21).
-
-The Device ID will read 0x6F (0x81 for SCH5307-NS, and 0x85 for SCH5317)
-The Device Rev currently reads 0x01
-
-Obtaining the HWM Base Address
-------------------------------
-
-The following is an example of how to read the HWM Base Address located in
-Logical Device 8::
-
-	; ENTER CONFIGURATION MODE
-	MOV	DX,02EH
-	MOV	AX,055H
-	OUT	DX,AL
-	; CONFIGURE REGISTER CRE0,
-	; LOGICAL DEVICE 8
-	MOV	DX,02EH
-	MOV	AL,07H
-	OUT	DX,AL ;Point to LD# Config Reg
-	MOV	DX,02FH
-	MOV	AL, 08H
-	OUT	DX,AL;Point to Logical Device 8
-	;
-	MOV	DX,02EH
-	MOV	AL,60H
-	OUT	DX,AL	; Point to HWM Base Addr MSB
-	MOV	DX,02FH
-	IN	AL,DX	; Get MSB of HWM Base Addr
-	; EXIT CONFIGURATION MODE
-	MOV	DX,02EH
-	MOV	AX,0AAH
-	OUT	DX,AL