docs: hwmon: Add an index file and rename docs to *.rst

Now that all files were converted to ReST format, rename them
and add an index.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

1 files changed, 0 insertions, 109 deletions

diff --git a/Documentation/hwmon/amc6821 b/Documentation/hwmon/amc6821
deleted file mode 100644
index d10eabcbc0f3..000000000000
--- a/Documentation/hwmon/amc6821
+++ /dev/null
@@ -1,109 +0,0 @@
-Kernel driver amc6821
-=====================
-
-Supported chips:
-
-	Texas Instruments AMC6821
-
-	Prefix: 'amc6821'
-
-	Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e
-
-	Datasheet: http://focus.ti.com/docs/prod/folders/print/amc6821.html
-
-Authors:
-	Tomaz Mertelj <tomaz.mertelj@guest.arnes.si>
-
-
-Description
------------
-
-This driver implements support for the Texas Instruments amc6821 chip.
-The chip has one on-chip and one remote temperature sensor and one pwm fan
-regulator.
-The pwm can be controlled either from software or automatically.
-
-The driver provides the following sensor accesses in sysfs:
-
-======================= ==      ===============================================
-temp1_input		ro	on-chip temperature
-temp1_min		rw	"
-temp1_max		rw	"
-temp1_crit		rw	"
-temp1_min_alarm		ro	"
-temp1_max_alarm		ro	"
-temp1_crit_alarm	ro	"
-
-temp2_input		ro	remote temperature
-temp2_min		rw	"
-temp2_max		rw	"
-temp2_crit		rw	"
-temp2_min_alarm		ro	"
-temp2_max_alarm		ro	"
-temp2_crit_alarm	ro	"
-temp2_fault		ro	"
-
-fan1_input		ro	tachometer speed
-fan1_min		rw	"
-fan1_max		rw	"
-fan1_fault		ro	"
-fan1_div		rw	Fan divisor can be either 2 or 4.
-
-pwm1			rw	pwm1
-pwm1_enable		rw	regulator mode, 1=open loop, 2=fan controlled
-				by remote temperature, 3=fan controlled by
-				combination of the on-chip temperature and
-				remote-sensor temperature,
-pwm1_auto_channels_temp ro	1 if pwm_enable==2, 3 if pwm_enable==3
-pwm1_auto_point1_pwm	ro	Hardwired to 0, shared for both
-				temperature channels.
-pwm1_auto_point2_pwm	rw	This value is shared for both temperature
-				channels.
-pwm1_auto_point3_pwm	rw	Hardwired to 255, shared for both
-				temperature channels.
-
-temp1_auto_point1_temp	ro	Hardwired to temp2_auto_point1_temp
-				which is rw. Below this temperature fan stops.
-temp1_auto_point2_temp	rw	The low-temperature limit of the proportional
-				range. Below this temperature
-				pwm1 = pwm1_auto_point2_pwm. It can go from
-				0 degree C to 124 degree C in steps of
-				4 degree C. Read it out after writing to get
-				the actual value.
-temp1_auto_point3_temp	rw	Above this temperature fan runs at maximum
-				speed. It can go from temp1_auto_point2_temp.
-				It can only have certain discrete values
-				which depend on temp1_auto_point2_temp and
-				pwm1_auto_point2_pwm. Read it out after
-				writing to get the actual value.
-
-temp2_auto_point1_temp	rw	Must be between 0 degree C and 63 degree C and
-				it defines the passive cooling temperature.
-				Below this temperature the fan stops in
-				the closed loop mode.
-temp2_auto_point2_temp	rw	The low-temperature limit of the proportional
-				range. Below this temperature
-				pwm1 = pwm1_auto_point2_pwm. It can go from
-				0 degree C to 124 degree C in steps
-				of 4 degree C.
-
-temp2_auto_point3_temp	rw	Above this temperature fan runs at maximum
-				speed. It can only have certain discrete
-				values which depend on temp2_auto_point2_temp
-				and pwm1_auto_point2_pwm. Read it out after
-				writing to get actual value.
-======================= ==      ===============================================
-
-
-Module parameters
------------------
-
-If your board has a BIOS that initializes the amc6821 correctly, you should
-load the module with: init=0.
-
-If your board BIOS doesn't initialize the chip, or you want
-different settings, you can set the following parameters:
-
-- init=1,
-- pwminv: 0 default pwm output, 1 inverts pwm output.
-