Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Highlights:

   1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.

   2) Add fib_sync_mem to control the amount of dirty memory we allow to
      queue up between synchronize RCU calls, from David Ahern.

   3) Make flow classifier more lockless, from Vlad Buslov.

   4) Add PHY downshift support to aquantia driver, from Heiner
      Kallweit.

   5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
      contention on SLAB spinlocks in heavy RPC workloads.

   6) Partial GSO offload support in XFRM, from Boris Pismenny.

   7) Add fast link down support to ethtool, from Heiner Kallweit.

   8) Use siphash for IP ID generator, from Eric Dumazet.

   9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
      entries, from David Ahern.

  10) Move skb->xmit_more into a per-cpu variable, from Florian
      Westphal.

  11) Improve eBPF verifier speed and increase maximum program size,
      from Alexei Starovoitov.

  12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
      spinlocks. From Neil Brown.

  13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.

  14) Improve link partner cap detection in generic PHY code, from
      Heiner Kallweit.

  15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
      Maguire.

  16) Remove SKB list implementation assumptions in SCTP, your's truly.

  17) Various cleanups, optimizations, and simplifications in r8169
      driver. From Heiner Kallweit.

  18) Add memory accounting on TX and RX path of SCTP, from Xin Long.

  19) Switch PHY drivers over to use dynamic featue detection, from
      Heiner Kallweit.

  20) Support flow steering without masking in dpaa2-eth, from Ioana
      Ciocoi.

  21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
      Pirko.

  22) Increase the strict parsing of current and future netlink
      attributes, also export such policies to userspace. From Johannes
      Berg.

  23) Allow DSA tag drivers to be modular, from Andrew Lunn.

  24) Remove legacy DSA probing support, also from Andrew Lunn.

  25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
      Haabendal.

  26) Add a generic tracepoint for TX queue timeouts to ease debugging,
      from Cong Wang.

  27) More indirect call optimizations, from Paolo Abeni"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
  cxgb4: Fix error path in cxgb4_init_module
  net: phy: improve pause mode reporting in phy_print_status
  dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
  net: macb: Change interrupt and napi enable order in open
  net: ll_temac: Improve error message on error IRQ
  net/sched: remove block pointer from common offload structure
  net: ethernet: support of_get_mac_address new ERR_PTR error
  net: usb: smsc: fix warning reported by kbuild test robot
  staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
  net: dsa: support of_get_mac_address new ERR_PTR error
  net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
  vrf: sit mtu should not be updated when vrf netdev is the link
  net: dsa: Fix error cleanup path in dsa_init_module
  l2tp: Fix possible NULL pointer dereference
  taprio: add null check on sched_nest to avoid potential null pointer dereference
  net: mvpp2: cls: fix less than zero check on a u32 variable
  net_sched: sch_fq: handle non connected flows
  net_sched: sch_fq: do not assume EDT packets are ordered
  net: hns3: use devm_kcalloc when allocating desc_cb
  net: hns3: some cleanup for struct hns3_enet_ring
  ...

25 files changed, 272 insertions, 200 deletions

diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt
index 0e21df94a53f..0b7d4d3758ea 100644
--- a/Documentation/devicetree/bindings/net/altera_tse.txt
+++ b/Documentation/devicetree/bindings/net/altera_tse.txt
@@ -46,9 +46,8 @@ Required properties:
 	- reg: phy id used to communicate to phy.
 	- device_type: Must be "ethernet-phy".
 
-Optional properties:
-- local-mac-address: See ethernet.txt in the same directory.
-- max-frame-size: See ethernet.txt in the same directory.
+The MAC address will be determined using the optional properties defined in
+ethernet.txt.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt
index 93dcb79a5f16..9c27dfcd1133 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt
@@ -24,8 +24,6 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 
 Optional properties:
-- mac-address: mac address to be assigned to the device. Can be overridden
-  by UEFI.
 - dma-coherent: Present if dma operations are coherent
 - amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate
   a unique interrupt for each DMA channel - this requires an additional
@@ -34,6 +32,9 @@ Optional properties:
     0 - 1GbE and 10GbE (default)
     1 - 2.5GbE and 10GbE
 
+The MAC address will be determined using the optional properties defined in
+ethernet.txt.
+
 The following optional properties are represented by an array with each
 value corresponding to a particular speed. The first array value represents
 the setting for the 1GbE speed, the second value for the 2.5GbE speed and
diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt
index 0bfad656a9ff..0120ebe93262 100644
--- a/Documentation/devicetree/bindings/net/brcm,amac.txt
+++ b/Documentation/devicetree/bindings/net/brcm,amac.txt
@@ -16,8 +16,8 @@ Required properties:
 				registers (required for Northstar2)
  - interrupts:	Interrupt number
 
-Optional properties:
-- mac-address:	See ethernet.txt file in the same directory
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Examples:
 
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 3264e1978d25..7c7ac5eb0313 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -49,10 +49,12 @@ Required properties:
 
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
-- mac-address		: See ethernet.txt file in the same directory
 - phy_id		: Specifies slave phy id (deprecated, use phy-handle)
 - phy-handle		: See ethernet.txt file in the same directory
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
 Slave sub-nodes:
 - fixed-link		: See fixed-link.txt file in the same directory
 
diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt
index ca83dcc84fb8..5e3579e72e2d 100644
--- a/Documentation/devicetree/bindings/net/davinci_emac.txt
+++ b/Documentation/devicetree/bindings/net/davinci_emac.txt
@@ -20,11 +20,12 @@ Required properties:
 Optional properties:
 - phy-handle: See ethernet.txt file in the same directory.
               If absent, davinci_emac driver defaults to 100/FULL.
-- nvmem-cells: phandle, reference to an nvmem node for the MAC address
-- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
 - ti,davinci-rmii-en: 1 byte, 1 means use RMII
 - ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM?
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
 Example (enbw_cmc board):
 	eth0: emac@1e20000 {
 		compatible = "ti,davinci-dm6467-emac";
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
index d66a5292b9d3..f66bb7ecdb82 100644
--- a/Documentation/devicetree/bindings/net/dsa/dsa.txt
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -1,12 +1,6 @@
 Distributed Switch Architecture Device Tree Bindings
 ----------------------------------------------------
 
-Two bindings exist, one of which has been deprecated due to
-limitations.
-
-Current Binding
----------------
-
 Switches are true Linux devices and can be probed by any means. Once
 probed, they register to the DSA framework, passing a node
 pointer. This node is expected to fulfil the following binding, and
@@ -71,9 +65,8 @@ properties, described in binding documents:
 			  Documentation/devicetree/bindings/net/fixed-link.txt
 			  for details.
 
-- local-mac-address	: See
-			  Documentation/devicetree/bindings/net/ethernet.txt
-			  for details.
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Example
 
@@ -262,152 +255,3 @@ linked into one DSA cluster.
 		};
 	};
 };
-
-Deprecated Binding
-------------------
-
-The deprecated binding makes use of a platform device to represent the
-switches. The switches themselves are not Linux devices, and make use
-of an MDIO bus for management.
-
-Required properties:
-- compatible		: Should be "marvell,dsa"
-- #address-cells	: Must be 2, first cell is the address on the MDIO bus
-			  and second cell is the address in the switch tree.
-			  Second cell is used only when cascading/chaining.
-- #size-cells		: Must be 0
-- dsa,ethernet		: Should be a phandle to a valid Ethernet device node
-- dsa,mii-bus		: Should be a phandle to a valid MDIO bus device node
-
-Optional properties:
-- interrupts		: property with a value describing the switch
-			  interrupt number (not supported by the driver)
-
-A DSA node can contain multiple switch chips which are therefore child nodes of
-the parent DSA node. The maximum number of allowed child nodes is 4
-(DSA_MAX_SWITCHES).
-Each of these switch child nodes should have the following required properties:
-
-- reg			: Contains two fields. The first one describes the
-			  address on the MII bus. The second is the switch
-			  number that must be unique in cascaded configurations
-- #address-cells	: Must be 1
-- #size-cells		: Must be 0
-
-A switch child node has the following optional property:
-
-- eeprom-length		: Set to the length of an EEPROM connected to the
-			  switch. Must be set if the switch can not detect
-			  the presence and/or size of a connected EEPROM,
-			  otherwise optional.
-
-A switch may have multiple "port" children nodes
-
-Each port children node must have the following mandatory properties:
-- reg			: Describes the port address in the switch
-- label			: Describes the label associated with this port, special
-			  labels are "cpu" to indicate a CPU port and "dsa" to
-			  indicate an uplink/downlink port.
-
-Note that a port labelled "dsa" will imply checking for the uplink phandle
-described below.
-
-Optional property:
-- link			: Should be a list of phandles to another switch's DSA port.
-			  This property is only used when switches are being
-			  chained/cascaded together. This port is used as outgoing port
-			  towards the phandle port, which can be more than one hop away.
-
-- phy-handle		: Phandle to a PHY on an external MDIO bus, not the
-			  switch internal one. See
-			  Documentation/devicetree/bindings/net/ethernet.txt
-			  for details.
-
-- phy-mode		: String representing the connection to the designated
-			  PHY node specified by the 'phy-handle' property. See
-			  Documentation/devicetree/bindings/net/ethernet.txt
-			  for details.
-
-- mii-bus		: Should be a phandle to a valid MDIO bus device node.
-			  This mii-bus will be used in preference to the
-			  global dsa,mii-bus defined above, for this switch.
-
-Optional subnodes:
-- fixed-link		: Fixed-link subnode describing a link to a non-MDIO
-			  managed entity. See
-			  Documentation/devicetree/bindings/net/fixed-link.txt
-			  for details.
-
-Example:
-
-	dsa@0 {
-		compatible = "marvell,dsa";
-		#address-cells = <2>;
-		#size-cells = <0>;
-
-		interrupts = <10>;
-		dsa,ethernet = <&ethernet0>;
-		dsa,mii-bus = <&mii_bus0>;
-
-		switch@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <16 0>;	/* MDIO address 16, switch 0 in tree */
-
-			port@0 {
-				reg = <0>;
-				label = "lan1";
-				phy-handle = <&phy0>;
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan2";
-			};
-
-			port@5 {
-				reg = <5>;
-				label = "cpu";
-			};
-
-			switch0port6: port@6 {
-				reg = <6>;
-				label = "dsa";
-				link = <&switch1port0
-				        &switch2port0>;
-			};
-		};
-
-		switch@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <17 1>;	/* MDIO address 17, switch 1 in tree */
-			mii-bus = <&mii_bus1>;
-			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
-			switch1port0: port@0 {
-				reg = <0>;
-				label = "dsa";
-				link = <&switch0port6>;
-			};
-			switch1port1: port@1 {
-				reg = <1>;
-				label = "dsa";
-				link = <&switch2port1>;
-			};
-		};
-
-		switch@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <18 2>;	/* MDIO address 18, switch 2 in tree */
-			mii-bus = <&mii_bus1>;
-
-			switch2port0: port@0 {
-				reg = <0>;
-				label = "dsa";
-				link = <&switch1port1
-				        &switch0port6>;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/net/dsa/sja1105.txt b/Documentation/devicetree/bindings/net/dsa/sja1105.txt
new file mode 100644
index 000000000000..13fd21074d48
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/sja1105.txt
@@ -0,0 +1,156 @@
+NXP SJA1105 switch driver
+=========================
+
+Required properties:
+
+- compatible:
+	Must be one of:
+	- "nxp,sja1105e"
+	- "nxp,sja1105t"
+	- "nxp,sja1105p"
+	- "nxp,sja1105q"
+	- "nxp,sja1105r"
+	- "nxp,sja1105s"
+
+	Although the device ID could be detected at runtime, explicit bindings
+	are required in order to be able to statically check their validity.
+	For example, SGMII can only be specified on port 4 of R and S devices,
+	and the non-SGMII devices, while pin-compatible, are not equal in terms
+	of support for RGMII internal delays (supported on P/Q/R/S, but not on
+	E/T).
+
+Optional properties:
+
+- sja1105,role-mac:
+- sja1105,role-phy:
+	Boolean properties that can be assigned under each port node. By
+	default (unless otherwise specified) a port is configured as MAC if it
+	is driving a PHY (phy-handle is present) or as PHY if it is PHY-less
+	(fixed-link specified, presumably because it is connected to a MAC).
+	The effect of this property (in either its implicit or explicit form)
+	is:
+	- In the case of MII or RMII it specifies whether the SJA1105 port is a
+	  clock source or sink for this interface (not applicable for RGMII
+	  where there is a Tx and an Rx clock).
+	- In the case of RGMII it affects the behavior regarding internal
+	  delays:
+	  1. If sja1105,role-mac is specified, and the phy-mode property is one
+	     of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity
+	     designated to apply the delay/clock skew necessary for RGMII
+	     is the PHY. The SJA1105 MAC does not apply any internal delays.
+	  2. If sja1105,role-phy is specified, and the phy-mode property is one
+	     of the above, the designated entity to apply the internal delays
+	     is the SJA1105 MAC (if hardware-supported). This is only supported
+	     by the second-generation (P/Q/R/S) hardware. On a first-generation
+	     E or T device, it is an error to specify an RGMII phy-mode other
+	     than "rgmii" for a port that is in fixed-link mode. In that case,
+	     the clock skew must either be added by the MAC at the other end of
+	     the fixed-link, or by PCB serpentine traces on the board.
+	These properties are required, for example, in the case where SJA1105
+	ports are at both ends of a MII/RMII PHY-less setup. One end would need
+	to have sja1105,role-mac, while the other sja1105,role-phy.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard
+DSA required and optional properties.
+
+Other observations
+------------------
+
+The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least
+one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
+cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
+depends on the SPI bus master driver.
+
+Example
+-------
+
+Ethernet switch connected via SPI to the host, CPU port wired to enet2:
+
+arch/arm/boot/dts/ls1021a-tsn.dts:
+
+/* SPI controller of the LS1021 */
+&dspi0 {
+	sja1105@1 {
+		reg = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "nxp,sja1105t";
+		spi-max-frequency = <4000000>;
+		fsl,spi-cs-sck-delay = <1000>;
+		fsl,spi-sck-cs-delay = <1000>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				/* ETH5 written on chassis */
+				label = "swp5";
+				phy-handle = <&rgmii_phy6>;
+				phy-mode = "rgmii-id";
+				reg = <0>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@1 {
+				/* ETH2 written on chassis */
+				label = "swp2";
+				phy-handle = <&rgmii_phy3>;
+				phy-mode = "rgmii-id";
+				reg = <1>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@2 {
+				/* ETH3 written on chassis */
+				label = "swp3";
+				phy-handle = <&rgmii_phy4>;
+				phy-mode = "rgmii-id";
+				reg = <2>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@3 {
+				/* ETH4 written on chassis */
+				phy-handle = <&rgmii_phy5>;
+				label = "swp4";
+				phy-mode = "rgmii-id";
+				reg = <3>;
+				/* Implicit "sja1105,role-mac;" */
+			};
+			port@4 {
+				/* Internal port connected to eth2 */
+				ethernet = <&enet2>;
+				phy-mode = "rgmii";
+				reg = <4>;
+				/* Implicit "sja1105,role-phy;" */
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+/* MDIO controller of the LS1021 */
+&mdio0 {
+	/* BCM5464 */
+	rgmii_phy3: ethernet-phy@3 {
+		reg = <0x3>;
+	};
+	rgmii_phy4: ethernet-phy@4 {
+		reg = <0x4>;
+	};
+	rgmii_phy5: ethernet-phy@5 {
+		reg = <0x5>;
+	};
+	rgmii_phy6: ethernet-phy@6 {
+		reg = <0x6>;
+	};
+};
+
+/* Ethernet master port of the LS1021 */
+&enet2 {
+	phy-connection-type = "rgmii";
+	status = "ok";
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt
index a68621580584..e88c3641d613 100644
--- a/Documentation/devicetree/bindings/net/ethernet.txt
+++ b/Documentation/devicetree/bindings/net/ethernet.txt
@@ -4,12 +4,14 @@ NOTE: All 'phy*' properties documented below are Ethernet specific. For the
 generic PHY 'phys' property, see
 Documentation/devicetree/bindings/phy/phy-bindings.txt.
 
-- local-mac-address: array of 6 bytes, specifies the MAC address that was
-  assigned to the network device;
 - mac-address: array of 6 bytes, specifies the MAC address that was last used by
   the boot program; should be used in cases where the MAC address assigned to
   the device by the boot program is different from the "local-mac-address"
   property;
+- local-mac-address: array of 6 bytes, specifies the MAC address that was
+  assigned to the network device;
+- nvmem-cells: phandle, reference to an nvmem node for the MAC address
+- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
 - max-speed: number, specifies maximum speed in Mbit/s supported by the device;
 - max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
   the maximum frame size (there's contradiction in the Devicetree
@@ -36,7 +38,7 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt.
   * "smii"
   * "xgmii"
   * "trgmii"
-  * "2000base-x",
+  * "1000base-x",
   * "2500base-x",
   * "rxaui"
   * "xaui"
diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac.txt b/Documentation/devicetree/bindings/net/hisilicon-femac.txt
index d11af5ecace8..5f96976f3cea 100644
--- a/Documentation/devicetree/bindings/net/hisilicon-femac.txt
+++ b/Documentation/devicetree/bindings/net/hisilicon-femac.txt
@@ -14,7 +14,6 @@ Required properties:
 	the PHY reset signal(optional).
 - reset-names: should contain the reset signal name "mac"(required)
 	and "phy"(optional).
-- mac-address: see ethernet.txt [1].
 - phy-mode: see ethernet.txt [1].
 - phy-handle: see ethernet.txt [1].
 - hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given.
@@ -22,6 +21,9 @@ Required properties:
 	The 2nd cell is reset pulse in micro seconds.
 	The 3rd cell is reset post-delay in micro seconds.
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt[1].
+
 [1] Documentation/devicetree/bindings/net/ethernet.txt
 
 Example:
diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt
index eea73adc678f..cddf46bf6b63 100644
--- a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt
+++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt
@@ -18,7 +18,6 @@ Required properties:
 - #size-cells: must be <0>.
 - phy-mode: see ethernet.txt [1].
 - phy-handle: see ethernet.txt [1].
-- mac-address: see ethernet.txt [1].
 - clocks: clock phandle and specifier pair.
 - clock-names: contain the clock name "mac_core"(required) and "mac_ifc"(optional).
 - resets: should contain the phandle to the MAC core reset signal(optional),
@@ -31,6 +30,9 @@ Required properties:
 	The 2nd cell is reset pulse in micro seconds.
 	The 3rd cell is reset post-delay in micro seconds.
 
+The MAC address will be determined using the properties defined in
+ethernet.txt[1].
+
 - PHY subnode: inherits from phy binding [2]
 
 [1] Documentation/devicetree/bindings/net/ethernet.txt
diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt
index 04ba1dc34fd6..3a65aabc76a2 100644
--- a/Documentation/devicetree/bindings/net/keystone-netcp.txt
+++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt
@@ -135,14 +135,14 @@ Optional properties:
 		are swapped.  The netcp driver will swap the two DWORDs
 		back to the proper order when this property is set to 2
 		when it obtains the mac address from efuse.
-- local-mac-address:	the driver is designed to use the of_get_mac_address api
-			only if efuse-mac is 0. When efuse-mac is 0, the MAC
-			address is obtained from local-mac-address. If this
-			attribute is not present, then the driver will use a
-			random MAC address.
 - "netcp-device label":	phandle to the device specification for each of NetCP
 			sub-module attached to this interface.
 
+The MAC address will be determined using the optional properties defined in
+ethernet.txt, as provided by the of_get_mac_address API and only if efuse-mac
+is set to 0. If any of the optional MAC address properties are not present,
+then the driver will use random MAC address.
+
 Example binding:
 
 netcp: netcp@2000000 {
diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
index 8b80515729d7..9c5e94482b5f 100644
--- a/Documentation/devicetree/bindings/net/macb.txt
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -26,9 +26,8 @@ Required properties:
 	Optional elements: 'tsu_clk'
 - clocks: Phandles to input clocks.
 
-Optional properties:
-- nvmem-cells: phandle, reference to an nvmem node for the MAC address
-- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Optional properties for PHY child node:
 - reset-gpios : Should specify the gpio for phy reset
diff --git a/Documentation/devicetree/bindings/net/marvell-pxa168.txt b/Documentation/devicetree/bindings/net/marvell-pxa168.txt
index 845a148a346e..5574af3554aa 100644
--- a/Documentation/devicetree/bindings/net/marvell-pxa168.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pxa168.txt
@@ -11,7 +11,9 @@ Optional properties:
 - #address-cells: must be 1 when using sub-nodes.
 - #size-cells: must be 0 when using sub-nodes.
 - phy-handle: see ethernet.txt file in the same directory.
-- local-mac-address: see ethernet.txt file in the same directory.
+
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Sub-nodes:
 Each PHY can be represented as a sub-node. This is not mandatory.
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt b/Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt
new file mode 100644
index 000000000000..3a96cbed9294
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt
@@ -0,0 +1,48 @@
+Properties for the MDIO bus multiplexer/glue of Amlogic G12a SoC family.
+
+This is a special case of a MDIO bus multiplexer. It allows to choose between
+the internal mdio bus leading to the embedded 10/100 PHY or the external
+MDIO bus.
+
+Required properties in addition to the generic multiplexer properties:
+- compatible : amlogic,g12a-mdio-mux
+- reg: physical address and length of the multiplexer/glue registers
+- clocks: list of clock phandle, one for each entry clock-names.
+- clock-names: should contain the following:
+  * "pclk"   : peripheral clock.
+  * "clkin0" : platform crytal
+  * "clkin1" : SoC 50MHz MPLL
+
+Example :
+
+mdio_mux: mdio-multiplexer@4c000 {
+	compatible = "amlogic,g12a-mdio-mux";
+	reg = <0x0 0x4c000 0x0 0xa4>;
+	clocks = <&clkc CLKID_ETH_PHY>,
+		 <&xtal>,
+		 <&clkc CLKID_MPLL_5OM>;
+	clock-names = "pclk", "clkin0", "clkin1";
+	mdio-parent-bus = <&mdio0>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ext_mdio: mdio@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	int_mdio: mdio@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		internal_ephy: ethernet-phy@8 {
+			compatible = "ethernet-phy-id0180.3301",
+				     "ethernet-phy-ieee802.3-c22";
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <8>;
+			max-speed = <100>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt
index 24626e082b83..a8275921a896 100644
--- a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt
+++ b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt
@@ -21,8 +21,9 @@ Optional properties:
 - spi-max-frequency: Maximum frequency of the SPI bus when accessing the ENC28J60.
   According to the ENC28J80 datasheet, the chip allows a maximum of 20 MHz, however,
   board designs may need to limit this value.
-- local-mac-address: See ethernet.txt in the same directory.
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Example (for NXP i.MX28 with pin control stuff for GPIO irq):
 
diff --git a/Documentation/devicetree/bindings/net/microchip,lan78xx.txt b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt
index 76786a0f6d3d..11a679530ae6 100644
--- a/Documentation/devicetree/bindings/net/microchip,lan78xx.txt
+++ b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt
@@ -7,9 +7,8 @@ The Device Tree properties, if present, override the OTP and EEPROM.
 Required properties:
 - compatible: Should be one of "usb424,7800", "usb424,7801" or "usb424,7850".
 
-Optional properties:
-- local-mac-address:   see ethernet.txt
-- mac-address:         see ethernet.txt
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Optional properties of the embedded PHY:
 - microchip,led-modes: a 0..4 element vector, with each element configuring
diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index 17c1d2bd00f6..9b9e5b1765dd 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -51,6 +51,10 @@ Optional Properties:
   to ensure the integrated PHY is used. The absence of this property indicates
   the muxers should be configured so that the external PHY is used.
 
+- resets: The reset-controller phandle and specifier for the PHY reset signal.
+
+- reset-names: Must be "phy" for the PHY reset signal.
+
 - reset-gpios: The GPIO phandle and specifier for the PHY reset signal.
 
 - reset-assert-us: Delay after the reset was asserted in microseconds.
@@ -67,6 +71,8 @@ ethernet-phy@0 {
 	interrupts = <35 IRQ_TYPE_EDGE_RISING>;
 	reg = <0>;
 
+	resets = <&rst 8>;
+	reset-names = "phy";
 	reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 	reset-assert-us = <1000>;
 	reset-deassert-us = <2000>;
diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt
index e4a8a51086df..21c36e524993 100644
--- a/Documentation/devicetree/bindings/net/qca,qca7000.txt
+++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt
@@ -23,7 +23,6 @@ Optional properties:
 		      Numbers smaller than 1000000 or greater than 16000000
 		      are invalid. Missing the property will set the SPI
 		      frequency to 8000000 Hertz.
-- local-mac-address : see ./ethernet.txt
 - qca,legacy-mode   : Set the SPI data transfer of the QCA7000 to legacy mode.
 		      In this mode the SPI master must toggle the chip select
 		      between each data word. In burst mode these gaps aren't
@@ -31,6 +30,9 @@ Optional properties:
 		      the QCA7000 is setup via GPIO pin strapping. If the
 		      property is missing the driver defaults to burst mode.
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
 SPI Example:
 
 /* Freescale i.MX28 SPI master*/
diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
index 824c0e23c544..7ef6118abd3d 100644
--- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
@@ -11,20 +11,21 @@ Required properties:
  - compatible: should contain one of the following:
    * "qcom,qca6174-bt"
    * "qcom,wcn3990-bt"
+   * "qcom,wcn3998-bt"
 
 Optional properties for compatible string qcom,qca6174-bt:
 
  - enable-gpios: gpio specifier used to enable chip
  - clocks: clock provided to the controller (SUSCLK_32KHZ)
 
-Required properties for compatible string qcom,wcn3990-bt:
+Required properties for compatible string qcom,wcn399x-bt:
 
  - vddio-supply: VDD_IO supply regulator handle.
  - vddxo-supply: VDD_XO supply regulator handle.
  - vddrf-supply: VDD_RF supply regulator handle.
  - vddch0-supply: VDD_CH0 supply regulator handle.
 
-Optional properties for compatible string qcom,wcn3990-bt:
+Optional properties for compatible string qcom,wcn399x-bt:
 
  - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
 
diff --git a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt
index 46e591178911..2cff6d8a585a 100644
--- a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt
+++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt
@@ -21,10 +21,12 @@ Required properties:
   range.
 
 Optional properties:
-- mac-address: 6 bytes, mac address
 - max-frame-size: Maximum Transfer Unit (IEEE defined MTU), rather
 		  than the maximum frame size.
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
 Example:
 
 	aliases {
diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
index 36f1aef585f0..ad3c6e109ce1 100644
--- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
+++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
@@ -103,8 +103,6 @@ Required properties:
 
 Optional properties:
 - dma-coherent: Present if dma operations are coherent
-- mac-address: See ethernet.txt in the same directory
-- local-mac-address: See ethernet.txt in the same directory
 - phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY.
   See ../gpio/gpio.txt.
 - snps,en-lpi: If present it enables use of the AXI low-power interface
@@ -133,6 +131,9 @@ Optional properties:
     - device_type: Must be "ethernet-phy".
     - fixed-mode device tree subnode: see fixed-link.txt in the same directory
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
 Examples:
 ethernet2@40010000 {
 	clock-names = "phy_ref_clk", "apb_pclk";
diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
index fc8f01718690..4e85fc495e87 100644
--- a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
+++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
@@ -31,8 +31,8 @@ Required properties:
  - socionext,syscon-phy-mode: A phandle to syscon with one argument
 	that configures phy mode. The argument is the ID of MAC instance.
 
-Optional properties:
- - local-mac-address: See ethernet.txt in the same directory.
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
 
 Required subnode:
  - mdio: A container for child nodes representing phy nodes.
diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt
index 0cff94fb0433..9d6c9feb12ff 100644
--- a/Documentation/devicetree/bindings/net/socionext-netsec.txt
+++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt
@@ -26,11 +26,12 @@ Required properties:
 Optional properties: (See ethernet.txt file in the same directory)
 - dma-coherent: Boolean property, must only be present if memory
 	accesses performed by the device are cache coherent.
-- local-mac-address: See ethernet.txt in the same directory.
-- mac-address: See ethernet.txt in the same directory.
 - max-speed: See ethernet.txt in the same directory.
 - max-frame-size: See ethernet.txt in the same directory.
 
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
 Example:
 	eth0: ethernet@522d0000 {
 		compatible = "socionext,synquacer-netsec";
diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt
index 7b9a776230c0..74665502f4cf 100644
--- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt
+++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt
@@ -13,11 +13,12 @@ properties:
 
 Optional properties:
 
-- mac-address: See ethernet.txt in the parent directory
-- local-mac-address: See ethernet.txt in the parent directory
 - ieee80211-freq-limit: See ieee80211.txt
 - mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data
 
+The driver is using of_get_mac_address API, so the MAC address can be as well
+be set with corresponding optional properties defined in net/ethernet.txt.
+
 Optional nodes:
 - led: Properties for a connected LED
   Optional properties:
diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt
index b7396c8c271c..aaaeeb5f935b 100644
--- a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt
+++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt
@@ -34,9 +34,9 @@ Optional properties:
 			ath9k wireless chip (in this case the calibration /
 			EEPROM data will be loaded from userspace using the
 			kernel firmware loader).
-- mac-address: See ethernet.txt in the parent directory
-- local-mac-address: See ethernet.txt in the parent directory
 
+The MAC address will be determined using the optional properties defined in
+net/ethernet.txt.
 
 In this example, the node is defined as child node of the PCI controller:
 &pci0 {