Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.12 kernel cycle.

  Core changes:

   - Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
     This was a much discussed change. It affects use cases where people
     write drivers that might or might not be using GPIO resources. I
     have decided that this is the lesser evil right now.

   - Make gpiod_count() behave consistently across different hardware
     descriptions.

   - Fix the syntax around open drain/open source to not infer active
     high/low semantics.

  New drivers:

   - A new single-register fixed-direction framework driver for hardware
     that have lines controlled by a single register that just work in
     one direction (out or in), including IRQ support.

   - Support the Fintek F71889A GPIO SuperIO controller.

   - Support the National NI 169445 MMIO GPIO.

   - Support for the X-Gene derivative of the DWC GPIO controller

   - Support for the Rohm BD9571MWV-M PMIC GPIO controller.

   - Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
     and replace both the Gemini and the Moxa ART custom drivers with
     this driver.

  Driver improvements:

   - A whole slew of drivers have their spinlocks chaned to raw
     spinlocks as they provide irqchips, and thus we are progressing on
     realtime compliance.

   - Use devm_irq_alloc_descs() in a slew of drivers, getting managed
     resources.

   - Support for the embedded PWM controller inside the MVEBU driver.

   - Debounce, open source and open drain support for the Aspeed driver.

   - Misc smaller fixes like spelling and syntax and whatnot"

* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: f7188x: Add a missing break
  gpio: omap: return error if requested debounce time is not possible
  gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
  gpio: gpio-wcove: fix GPIO IRQ status mask
  gpio: DT bindings, move tca9554 from pcf857x to pca953x
  gpio: move tca9554 from pcf857x to pca953x
  gpio: arizona: Correct check whether the pin is an input
  gpio: Add XRA1403 DTS binding documentation
  dt-bindings: add exar to vendor prefixes list
  gpio: gpio-wcove: fix irq pending status bit width
  gpio: dwapb: use dwapb_read instead of readl_relaxed
  gpio: aspeed: Add open-source and open-drain support
  gpio: aspeed: Add debounce support
  gpio: aspeed: dt: Add optional clocks property
  gpio: aspeed: dt: Fix description alignment in bindings document
  gpio: mvebu: Add limited PWM support
  gpio: Use unsigned int for interrupt numbers
  gpio: f7188x: Add F71889A GPIO support.
  gpio: core: Decouple open drain/source flag with active low/high
  gpio: arizona: Correct handling for reading input GPIOs
  ...

10 files changed, 153 insertions, 24 deletions

diff --git a/Documentation/devicetree/bindings/gpio/cortina,gemini-gpio.txt b/Documentation/devicetree/bindings/gpio/faraday,ftgpio010.txt
index 5c9246c054e5..d04236558619 100644
--- a/Documentation/devicetree/bindings/gpio/cortina,gemini-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/faraday,ftgpio010.txt
@@ -1,8 +1,11 @@
-Cortina Systems Gemini GPIO Controller
+Faraday Technology FTGPIO010 GPIO Controller
 
 Required properties:
 
-- compatible : Must be "cortina,gemini-gpio"
+- compatible : Should be one of
+  "cortina,gemini-gpio", "faraday,ftgpio010"
+  "moxa,moxart-gpio", "faraday,ftgpio010"
+  "faraday,ftgpio010"
 - reg : Should contain registers location and length
 - interrupts : Should contain the interrupt line for the GPIO block
 - gpio-controller : marks this as a GPIO controller
@@ -14,7 +17,7 @@ Required properties:
 Example:
 
 gpio@4d000000 {
-	compatible = "cortina,gemini-gpio";
+	compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
 	reg = <0x4d000000 0x100>;
 	interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
 	gpio-controller;
diff --git a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt
index 393bb2ed8a77..c756afa88cc6 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt
@@ -17,7 +17,8 @@ Required properties:
 
 Optional properties:
 
-- interrupt-parent     : The parent interrupt controller, optional if inherited
+- interrupt-parent      : The parent interrupt controller, optional if inherited
+- clocks                : A phandle to the HPLL clock node for debounce timings
 
 The gpio and interrupt properties are further described in their respective
 bindings documentation:
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
index a6f3bec1da7d..42c3bb2d53e8 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
@@ -38,6 +38,24 @@ Required properties:
 - #gpio-cells: Should be two. The first cell is the pin number. The
   second cell is reserved for flags, unused at the moment.
 
+Optional properties:
+
+In order to use the GPIO lines in PWM mode, some additional optional
+properties are required. Only Armada 370 and XP support these properties.
+
+- compatible: Must contain "marvell,armada-370-xp-gpio"
+
+- reg: an additional register set is needed, for the GPIO Blink
+  Counter on/off registers.
+
+- reg-names: Must contain an entry "pwm" corresponding to the
+  additional register range needed for PWM operation.
+
+- #pwm-cells: Should be two. The first cell is the GPIO line number. The
+  second cell is the period in nanoseconds.
+
+- clocks: Must be a phandle to the clock for the GPIO controller.
+
 Example:
 
 		gpio0: gpio@d0018100 {
@@ -51,3 +69,17 @@ Example:
 			#interrupt-cells = <2>;
 			interrupts = <16>, <17>, <18>, <19>;
 		};
+
+		gpio1: gpio@18140 {
+			compatible = "marvell,armada-370-xp-gpio";
+			reg = <0x18140 0x40>, <0x181c8 0x08>;
+			reg-names = "gpio", "pwm";
+			ngpios = <17>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			#pwm-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <87>, <88>, <89>;
+			clocks = <&coreclk 0>;
+		};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
index e63935710011..7f57271df2bc 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
@@ -26,6 +26,7 @@ Required properties:
 	ti,tca6416
 	ti,tca6424
 	ti,tca9539
+	ti,tca9554
 	onsemi,pca9654
 	exar,xra1202
 
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
index ada4e2973323..7d3bd631d011 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
@@ -25,7 +25,6 @@ Required Properties:
     - "nxp,pcf8574": For the NXP PCF8574
     - "nxp,pcf8574a": For the NXP PCF8574A
     - "nxp,pcf8575": For the NXP PCF8575
-    - "ti,tca9554": For the TI TCA9554
 
   - reg: I2C slave address.
 
diff --git a/Documentation/devicetree/bindings/gpio/gpio-thunderx.txt b/Documentation/devicetree/bindings/gpio/gpio-thunderx.txt
new file mode 100644
index 000000000000..3f883ae29d11
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-thunderx.txt
@@ -0,0 +1,27 @@
+Cavium ThunderX/OCTEON-TX GPIO controller bindings
+
+Required Properties:
+- reg: The controller bus address.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Must be 2.
+  - First cell is the GPIO pin number relative to the controller.
+  - Second cell is a standard generic flag bitfield as described in gpio.txt.
+
+Optional Properties:
+- compatible: "cavium,thunder-8890-gpio", unused as PCI driver binding is used.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Must be present and have value of 2 if
+                    "interrupt-controller" is present.
+  - First cell is the GPIO pin number relative to the controller.
+  - Second cell is triggering flags as defined in interrupts.txt.
+
+Example:
+
+gpio_6_0: gpio@6,0 {
+	compatible = "cavium,thunder-8890-gpio";
+	reg = <0x3000 0 0 0 0>; /*  DEVFN = 0x30 (6:0) */
+	gpio-controller;
+	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xra1403.txt b/Documentation/devicetree/bindings/gpio/gpio-xra1403.txt
new file mode 100644
index 000000000000..e13cc399b363
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xra1403.txt
@@ -0,0 +1,46 @@
+GPIO Driver for XRA1403 16-BIT GPIO Expander With Reset Input from EXAR
+
+The XRA1403 is an 16-bit GPIO expander with an SPI interface. Features available:
+	- Individually programmable inputs:
+		- Internal pull-up resistors
+		- Polarity inversion
+		- Individual interrupt enable
+		- Rising edge and/or Falling edge interrupt
+		- Input filter
+	- Individually programmable outputs
+		- Output Level Control
+		- Output Three-State Control
+
+Properties
+----------
+Check documentation for SPI and GPIO controllers regarding properties needed to configure the node.
+
+	- compatible = "exar,xra1403".
+	- reg - SPI id of the device.
+	- gpio-controller - marks the node as gpio.
+	- #gpio-cells - should be two where the first cell is the pin number
+		and the second one is used for optional parameters.
+
+Optional properties:
+-------------------
+	- reset-gpios: in case available used to control the device reset line.
+	- interrupt-controller - marks the node as interrupt controller.
+	- #interrupt-cells - should be two and represents the number of cells
+		needed to encode interrupt source.
+
+Example
+--------
+
+	gpioxra0: gpio@2 {
+		compatible = "exar,xra1403";
+		reg = <2>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		reset-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <1000000>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt b/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt
deleted file mode 100644
index f8e8f185a3db..000000000000
--- a/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt
+++ /dev/null
@@ -1,19 +0,0 @@
-MOXA ART GPIO Controller
-
-Required properties:
-
-- #gpio-cells : Should be 2, The first cell is the pin number,
-		the second cell is used to specify polarity:
-			0 = active high
-			1 = active low
-- compatible : Must be "moxa,moxart-gpio"
-- reg : Should contain registers location and length
-
-Example:
-
-	gpio: gpio@98700000 {
-		gpio-controller;
-		#gpio-cells = <2>;
-		compatible = "moxa,moxart-gpio";
-		reg =	<0x98700000 0xC>;
-	};
diff --git a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
new file mode 100644
index 000000000000..ca2f8c745a27
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
@@ -0,0 +1,38 @@
+Bindings for the National Instruments 169445 GPIO NAND controller
+
+The 169445 GPIO NAND controller has two memory mapped GPIO registers, one
+for input (the ready signal) and one for output (control signals).  It is
+intended to be used with the GPIO NAND driver.
+
+Required properties:
+	- compatible: should be "ni,169445-nand-gpio"
+	- reg-names: must contain
+		"dat" - data register
+	- reg: address + size pairs describing the GPIO register sets;
+		order must correspond with the order of entries in reg-names
+	- #gpio-cells: must be set to 2. The first cell is the pin number and
+			the second cell is used to specify the gpio polarity:
+			0 = active high
+			1 = active low
+	- gpio-controller: Marks the device node as a gpio controller.
+
+Optional properties:
+	- no-output: disables driving output on the pins
+
+Examples:
+	gpio1: nand-gpio-out@1f300010 {
+		compatible = "ni,169445-nand-gpio";
+		reg = <0x1f300010 0x4>;
+		reg-names = "dat";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio2: nand-gpio-in@1f300014 {
+		compatible = "ni,169445-nand-gpio";
+		reg = <0x1f300014 0x4>;
+		reg-names = "dat";
+		gpio-controller;
+		#gpio-cells = <2>;
+		no-output;
+	};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index bbb8174405bc..257ec07cbaa0 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -103,6 +103,7 @@ ettus	NI Ettus Research
 eukrea  Eukréa Electromatique
 everest	Everest Semiconductor Co. Ltd.
 everspin	Everspin Technologies, Inc.
+exar	Exar Corporation
 excito	Excito
 ezchip	EZchip Semiconductor
 faraday	Faraday Technology Corporation