Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux

Merge upstream tree in order to reinstate crct10dif.

50 files changed, 1341 insertions, 56 deletions

diff --git a/Documentation/devicetree/bindings/arm/global_timer.txt b/Documentation/devicetree/bindings/arm/global_timer.txt
new file mode 100644
index 000000000000..1e548981eda4
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/global_timer.txt
@@ -0,0 +1,24 @@
+
+* ARM Global Timer
+	Cortex-A9 are often associated with a per-core Global timer.
+
+** Timer node required properties:
+
+- compatible : Should be "arm,cortex-a9-global-timer"
+		Driver supports versions r2p0 and above.
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the GT timer
+	register window.
+
+- clocks : Should be phandle to a clock.
+
+Example:
+
+	timer@2c000600 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0x2c000600 0x20>;
+		interrupts = <1 13 0xf01>;
+		clocks = <&arm_periph_clk>;
+	};
diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt
index c80e8a3402f0..c280a0e6f42d 100644
--- a/Documentation/devicetree/bindings/dma/atmel-dma.txt
+++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt
@@ -24,8 +24,11 @@ The three cells in order are:
 1. A phandle pointing to the DMA controller.
 2. The memory interface (16 most significant bits), the peripheral interface
 (16 less significant bits).
-3. The peripheral identifier for the hardware handshaking interface. The
-identifier can be different for tx and rx.
+3. Parameters for the at91 DMA configuration register which are device
+dependant:
+  - bit 7-0: peripheral identifier for the hardware handshaking interface. The
+  identifier can be different for tx and rx.
+  - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 1 for ASAP.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt
new file mode 100644
index 000000000000..2717ecb47db9
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt
@@ -0,0 +1,48 @@
+* Freescale Direct Memory Access (DMA) Controller for i.MX
+
+This document will only describe differences to the generic DMA Controller and
+DMA request bindings as described in dma/dma.txt .
+
+* DMA controller
+
+Required properties:
+- compatible : Should be "fsl,<chip>-dma". chip can be imx1, imx21 or imx27
+- reg : Should contain DMA registers location and length
+- interrupts : First item should be DMA interrupt, second one is optional and
+    should contain DMA Error interrupt
+- #dma-cells : Has to be 1. imx-dma does not support anything else.
+
+Optional properties:
+- #dma-channels : Number of DMA channels supported. Should be 16.
+- #dma-requests : Number of DMA requests supported.
+
+Example:
+
+	dma: dma@10001000 {
+		compatible = "fsl,imx27-dma";
+		reg = <0x10001000 0x1000>;
+		interrupts = <32 33>;
+		#dma-cells = <1>;
+		#dma-channels = <16>;
+	};
+
+
+* DMA client
+
+Clients have to specify the DMA requests with phandles in a list.
+
+Required properties:
+- dmas: List of one or more DMA request specifiers. One DMA request specifier
+    consists of a phandle to the DMA controller followed by the integer
+    specifiying the request line.
+- dma-names: List of string identifiers for the DMA requests. For the correct
+    names, have a look at the specific client driver.
+
+Example:
+
+	sdhci1: sdhci@10013000 {
+		...
+		dmas = <&dma 7>;
+		dma-names = "rx-tx";
+		...
+	};
diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
index d1e3f443e205..68cee4f5539f 100644
--- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -4,14 +4,70 @@ Required properties:
 - compatible : Should be "fsl,<chip>-sdma"
 - reg : Should contain SDMA registers location and length
 - interrupts : Should contain SDMA interrupt
+- #dma-cells : Must be <3>.
+  The first cell specifies the DMA request/event ID.  See details below
+  about the second and third cell.
 - fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM
   scripts firmware
 
+The second cell of dma phandle specifies the peripheral type of DMA transfer.
+The full ID of peripheral types can be found below.
+
+	ID	transfer type
+	---------------------
+	0	MCU domain SSI
+	1	Shared SSI
+	2	MMC
+	3	SDHC
+	4	MCU domain UART
+	5	Shared UART
+	6	FIRI
+	7	MCU domain CSPI
+	8	Shared CSPI
+	9	SIM
+	10	ATA
+	11	CCM
+	12	External peripheral
+	13	Memory Stick Host Controller
+	14	Shared Memory Stick Host Controller
+	15	DSP
+	16	Memory
+	17	FIFO type Memory
+	18	SPDIF
+	19	IPU Memory
+	20	ASRC
+	21	ESAI
+
+The third cell specifies the transfer priority as below.
+
+	ID	transfer priority
+	-------------------------
+	0	High
+	1	Medium
+	2	Low
+
 Examples:
 
 sdma@83fb0000 {
 	compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
 	reg = <0x83fb0000 0x4000>;
 	interrupts = <6>;
+	#dma-cells = <3>;
 	fsl,sdma-ram-script-name = "sdma-imx51.bin";
 };
+
+DMA clients connected to the i.MX SDMA controller must use the format
+described in the dma.txt file.
+
+Examples:
+
+ssi2: ssi@70014000 {
+	compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+	reg = <0x70014000 0x4000>;
+	interrupts = <30>;
+	clocks = <&clks 49>;
+	dmas = <&sdma 24 1 0>,
+	       <&sdma 25 1 0>;
+	dma-names = "rx", "tx";
+	fsl,fifo-depth = <15>;
+};
diff --git a/Documentation/devicetree/bindings/dma/shdma.txt b/Documentation/devicetree/bindings/dma/shdma.txt
new file mode 100644
index 000000000000..c15994aa1939
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/shdma.txt
@@ -0,0 +1,75 @@
+* SHDMA Device Tree bindings
+
+Sh-/r-mobile and r-car systems often have multiple identical DMA controller
+instances, capable of serving any of a common set of DMA slave devices, using
+the same configuration. To describe this topology we require all compatible
+SHDMA DT nodes to be placed under a DMA multiplexer node. All such compatible
+DMAC instances have the same number of channels and use the same DMA
+descriptors. Therefore respective DMA DT bindings can also all be placed in the
+multiplexer node. Even if there is only one such DMAC instance on a system, it
+still has to be placed under such a multiplexer node.
+
+* DMA multiplexer
+
+Required properties:
+- compatible:	should be "renesas,shdma-mux"
+- #dma-cells:	should be <1>, see "dmas" property below
+
+Optional properties (currently unused):
+- dma-channels:	number of DMA channels
+- dma-requests:	number of DMA request signals
+
+* DMA controller
+
+Required properties:
+- compatible:	should be "renesas,shdma"
+
+Example:
+	dmac: dma-mux0 {
+		compatible = "renesas,shdma-mux";
+		#dma-cells = <1>;
+		dma-channels = <6>;
+		dma-requests = <256>;
+		reg = <0 0>;	/* Needed for AUXDATA */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dma0: shdma@fe008020 {
+			compatible = "renesas,shdma";
+			reg = <0xfe008020 0x270>,
+				<0xfe009000 0xc>;
+			interrupt-parent = <&gic>;
+			interrupts = <0 34 4
+					0 28 4
+					0 29 4
+					0 30 4
+					0 31 4
+					0 32 4
+					0 33 4>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5";
+		};
+
+		dma1: shdma@fe018020 {
+			...
+		};
+
+		dma2: shdma@fe028020 {
+			...
+		};
+	};
+
+* DMA client
+
+Required properties:
+- dmas:		a list of <[DMA multiplexer phandle] [MID/RID value]> pairs,
+		where MID/RID values are fixed handles, specified in the SoC
+		manual
+- dma-names:	a list of DMA channel names, one per "dmas" entry
+
+Example:
+	dmas = <&dmac 0xd1
+		&dmac 0xd2>;
+	dma-names = "tx", "rx";
diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
index e5f130159ae1..fff10da5e927 100644
--- a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
+++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
@@ -10,6 +10,14 @@ Recommended properties:
    services interrupts for this device.
  - ti,hwmods: Name of the hwmod associated to the LCDC
 
+Optional properties:
+ - max-bandwidth: The maximum pixels per second that the memory
+   interface / lcd controller combination can sustain
+ - max-width: The maximum horizontal pixel width supported by
+   the lcd controller.
+ - max-pixelclock: The maximum pixel clock that can be supported
+   by the lcd controller in KHz.
+
 Example:
 
 	fb: fb@4830e000 {
diff --git a/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt b/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt
new file mode 100644
index 000000000000..370dee3226d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/men-a021-wdt.txt
@@ -0,0 +1,25 @@
+Bindings for MEN A21 Watchdog device connected to GPIO lines
+
+Required properties:
+- compatible: "men,a021-wdt"
+- gpios: Specifies the pins that control the Watchdog, order:
+  1: Watchdog enable
+  2: Watchdog fast-mode
+  3: Watchdog trigger
+  4: Watchdog reset cause bit 0
+  5: Watchdog reset cause bit 1
+  6: Watchdog reset cause bit 2
+
+Optional properties:
+- None
+
+Example:
+	watchdog {
+		compatible ="men,a021-wdt";
+		gpios = <&gpio3 9  1	/* WD_EN */
+			 &gpio3 10 1	/* WD_FAST */
+			 &gpio3 11 1	/* WD_TRIG */
+			 &gpio3 6  1	/* RST_CAUSE[0] */
+			 &gpio3 7  1	/* RST_CAUSE[1] */
+			 &gpio3 8  1>;	/* RST_CAUSE[2] */
+	};
diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt
new file mode 100644
index 000000000000..5f7619c22743
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/ads7846.txt
@@ -0,0 +1,91 @@
+Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
+SPI driven touch screen controllers.
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in
+
+	Documentation/devicetree/bindings/spi/spi-bus.txt
+
+must be specified.
+
+Additional required properties:
+
+	compatible		Must be one of the following, depending on the
+				model:
+					"ti,tsc2046"
+					"ti,ads7843"
+					"ti,ads7845"
+					"ti,ads7846"
+					"ti,ads7873"
+
+	interrupt-parent
+	interrupts		An interrupt node describing the IRQ line the chip's
+				!PENIRQ pin is connected to.
+	vcc-supply		A regulator node for the supply voltage.
+
+
+Optional properties:
+
+	ti,vref-delay-usecs		vref supply delay in usecs, 0 for
+					external vref (u16).
+	ti,vref-mv			The VREF voltage, in millivolts (u16).
+	ti,keep-vref-on			set to keep vref on for differential
+					measurements as well
+	ti,swap-xy			swap x and y axis
+	ti,settle-delay-usec		Settling time of the analog signals;
+					a function of Vcc and the capacitance
+					on the X/Y drivers.  If set to non-zero,
+					two samples are taken with settle_delay
+					us apart, and the second one is used.
+					~150 uSec with 0.01uF caps (u16).
+	ti,penirq-recheck-delay-usecs	If set to non-zero, after samples are
+					taken this delay is applied and penirq
+					is rechecked, to help avoid false
+					events.  This value is affected by the
+					material used to build the touch layer
+					(u16).
+	ti,x-plate-ohms			Resistance of the X-plate,
+					in Ohms (u16).
+	ti,y-plate-ohms			Resistance of the Y-plate,
+					in Ohms (u16).
+	ti,x-min			Minimum value on the X axis (u16).
+	ti,y-min			Minimum value on the Y axis (u16).
+	ti,x-max			Maximum value on the X axis (u16).
+	ti,y-max			Minimum value on the Y axis (u16).
+	ti,pressure-min			Minimum reported pressure value
+					(threshold) - u16.
+	ti,pressure-max			Maximum reported pressure value (u16).
+	ti,debounce-max			Max number of additional readings per
+					sample (u16).
+	ti,debounce-tol			Tolerance used for filtering (u16).
+	ti,debounce-rep			Additional consecutive good readings
+					required after the first two (u16).
+	ti,pendown-gpio-debounce	Platform specific debounce time for the
+					pendown-gpio (u32).
+	pendown-gpio			GPIO handle describing the pin the !PENIRQ
+					line is connected to.
+	linux,wakeup			use any event on touchscreen as wakeup event.
+
+
+Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
+
+	spi_controller {
+		tsc2046@0 {
+			reg = <0>;	/* CS0 */
+			compatible = "ti,tsc2046";
+			interrupt-parent = <&gpio1>;
+			interrupts = <8 0>;	/* BOOT6 / GPIO 8 */
+			spi-max-frequency = <1000000>;
+			pendown-gpio = <&gpio1 8 0>;
+			vcc-supply = <&reg_vcc3>;
+
+			ti,x-min = /bits/ 16 <0>;
+			ti,x-max = /bits/ 16 <8000>;
+			ti,y-min = /bits/ 16 <0>;
+			ti,y-max = /bits/ 16 <4800>;
+			ti,x-plate-ohms = /bits/ 16 <40>;
+			ti,pressure-max = /bits/ 16 <255>;
+
+			linux,wakeup;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
new file mode 100644
index 000000000000..491c97b78384
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
@@ -0,0 +1,44 @@
+* TI - TSC ADC (Touschscreen and analog digital converter)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties:
+- child "tsc"
+	ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
+		  support on the platform.
+	ti,x-plate-resistance: X plate resistance
+	ti,coordiante-readouts: The sequencer supports a total of 16
+				programmable steps each step is used to
+				read a single coordinate. A single
+                                readout is enough but multiple reads can
+				increase the quality.
+				A value of 5 means, 5 reads for X, 5 for
+				Y and 2 for Z (always). This utilises 12
+				of the 16 software steps available. The
+				remaining 4 can be used by the ADC.
+	ti,wire-config: Different boards could have a different order for
+			connecting wires on touchscreen. We need to provide an
+			8 bit number where in the 1st four bits represent the
+			analog lines and the next 4 bits represent positive/
+			negative terminal on that input line. Notations to
+			represent the input lines and terminals resoectively
+			is as follows:
+			AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+			XP  = 0, XN = 1, YP = 2, YN = 3.
+- child "adc"
+	ti,adc-channels: List of analog inputs available for ADC.
+			 AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+
+Example:
+	tscadc: tscadc@44e0d000 {
+		compatible = "ti,am3359-tscadc";
+		tsc {
+			ti,wires = <4>;
+			ti,x-plate-resistance = <200>;
+			ti,coordiante-readouts = <5>;
+			ti,wire-config = <0x00 0x11 0x22 0x33>;
+		};
+
+		adc {
+			ti,adc-channels = <4 5 6 7>;
+		};
+	}
diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
new file mode 100644
index 000000000000..e34c6cdd8ba8
--- /dev/null
+++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
@@ -0,0 +1,70 @@
+* ARM System MMU Architecture Implementation
+
+ARM SoCs may contain an implementation of the ARM System Memory
+Management Unit Architecture, which can be used to provide 1 or 2 stages
+of address translation to bus masters external to the CPU.
+
+The SMMU may also raise interrupts in response to various fault
+conditions.
+
+** System MMU required properties:
+
+- compatible    : Should be one of:
+
+                        "arm,smmu-v1"
+                        "arm,smmu-v2"
+                        "arm,mmu-400"
+                        "arm,mmu-500"
+
+                  depending on the particular implementation and/or the
+                  version of the architecture implemented.
+
+- reg           : Base address and size of the SMMU.
+
+- #global-interrupts : The number of global interrupts exposed by the
+                       device.
+
+- interrupts    : Interrupt list, with the first #global-irqs entries
+                  corresponding to the global interrupts and any
+                  following entries corresponding to context interrupts,
+                  specified in order of their indexing by the SMMU.
+
+                  For SMMUv2 implementations, there must be exactly one
+                  interrupt per context bank. In the case of a single,
+                  combined interrupt, it must be listed multiple times.
+
+- mmu-masters   : A list of phandles to device nodes representing bus
+                  masters for which the SMMU can provide a translation
+                  and their corresponding StreamIDs (see example below).
+                  Each device node linked from this list must have a
+                  "#stream-id-cells" property, indicating the number of
+                  StreamIDs associated with it.
+
+** System MMU optional properties:
+
+- smmu-parent   : When multiple SMMUs are chained together, this
+                  property can be used to provide a phandle to the
+                  parent SMMU (that is the next SMMU on the path going
+                  from the mmu-masters towards memory) node for this
+                  SMMU.
+
+Example:
+
+        smmu {
+                compatible = "arm,smmu-v1";
+                reg = <0xba5e0000 0x10000>;
+                #global-interrupts = <2>;
+                interrupts = <0 32 4>,
+                             <0 33 4>,
+                             <0 34 4>, /* This is the first context interrupt */
+                             <0 35 4>,
+                             <0 36 4>,
+                             <0 37 4>;
+
+                /*
+                 * Two DMA controllers, the first with two StreamIDs (0xd01d
+                 * and 0xd01e) and the second with only one (0xd11c).
+                 */
+                mmu-masters = <&dma0 0xd01d 0xd01e>,
+                              <&dma1 0xd11c>;
+        };
diff --git a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt
index de9f6b78ee51..0bf6fb7fbeab 100644
--- a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt
+++ b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt
@@ -2,8 +2,10 @@ Exynos4x12/Exynos5 SoC series camera host interface (FIMC-LITE)
 
 Required properties:
 
-- compatible	: should be "samsung,exynos4212-fimc-lite" for Exynos4212 and
-		  Exynos4412 SoCs;
+- compatible	: should be one of:
+		  "samsung,exynos4212-fimc-lite" for Exynos4212/4412 SoCs,
+		  "samsung,exynos5250-fimc-lite" for Exynos5250 compatible
+		   devices;
 - reg		: physical base address and size of the device memory mapped
 		  registers;
 - interrupts	: should contain FIMC-LITE interrupt;
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
new file mode 100644
index 000000000000..cb60443ff78f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
@@ -0,0 +1,40 @@
+* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor
+
+The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+- compatible: value should be either one among the following
+	(a) "aptina,mt9p031" for mt9p031 sensor
+	(b) "aptina,mt9p031m" for mt9p031m sensor
+
+- input-clock-frequency: Input clock frequency.
+
+- pixel-clock-frequency: Pixel clock frequency.
+
+Optional Properties:
+- reset-gpios: Chip reset GPIO
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		mt9p031@5d {
+			compatible = "aptina,mt9p031";
+			reg = <0x5d>;
+			reset-gpios = <&gpio3 30 0>;
+
+			port {
+				mt9p031_1: endpoint {
+					input-clock-frequency = <6000000>;
+					pixel-clock-frequency = <96000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
new file mode 100644
index 000000000000..46752cc71f2e
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
@@ -0,0 +1,44 @@
+* Texas Instruments TVP514x video decoder
+
+The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip
+digital video decoder that digitizes and decodes all popular baseband analog
+video formats into digital video component. The tvp514x decoder supports analog-
+to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
+conversion and decoding of NTSC, PAL and SECAM composite and S-video into
+component YCbCr.
+
+Required Properties :
+- compatible : value should be either one among the following
+	(a) "ti,tvp5146" for tvp5146 decoder.
+	(b) "ti,tvp5146m2" for tvp5146m2 decoder.
+	(c) "ti,tvp5147" for tvp5147 decoder.
+	(d) "ti,tvp5147m1" for tvp5147m1 decoder.
+
+- hsync-active: HSYNC Polarity configuration for endpoint.
+
+- vsync-active: VSYNC Polarity configuration for endpoint.
+
+- pclk-sample: Clock polarity of the endpoint.
+
+For further reading on port node refer to Documentation/devicetree/bindings/
+media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp514x@5c {
+			compatible = "ti,tvp5146";
+			reg = <0x5c>;
+
+			port {
+				tvp514x_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt
index 51c776b7f7a3..96312f6c4c26 100644
--- a/Documentation/devicetree/bindings/media/samsung-fimc.txt
+++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt
@@ -127,22 +127,22 @@ Example:
 				};
 			};
 		};
-	};
 
-	/* MIPI CSI-2 bus IF sensor */
-	s5c73m3: sensor@0x1a {
-		compatible = "samsung,s5c73m3";
-		reg = <0x1a>;
-		vddio-supply = <...>;
+		/* MIPI CSI-2 bus IF sensor */
+		s5c73m3: sensor@0x1a {
+			compatible = "samsung,s5c73m3";
+			reg = <0x1a>;
+			vddio-supply = <...>;
 
-		clock-frequency = <24000000>;
-		clocks = <...>;
-		clock-names = "mclk";
+			clock-frequency = <24000000>;
+			clocks = <...>;
+			clock-names = "mclk";
 
-		port {
-			s5c73m3_1: endpoint {
-				data-lanes = <1 2 3 4>;
-				remote-endpoint = <&csis0_ep>;
+			port {
+				s5c73m3_1: endpoint {
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csis0_ep>;
+				};
 			};
 		};
 	};
diff --git a/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt
index 5f8e28e2484f..be45f0b1a449 100644
--- a/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt
+++ b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt
@@ -5,8 +5,8 @@ Required properties:
 
 - compatible	  : "samsung,s5pv210-csis" for S5PV210 (S5PC110),
 		    "samsung,exynos4210-csis" for Exynos4210 (S5PC210),
-		    "samsung,exynos4212-csis" for Exynos4212/Exynos4412
-		    SoC series;
+		    "samsung,exynos4212-csis" for Exynos4212/Exynos4412,
+		    "samsung,exynos5250-csis" for Exynos5250;
 - reg		  : offset and length of the register set for the device;
 - interrupts      : should contain MIPI CSIS interrupt; the format of the
 		    interrupt specifier depends on the interrupt controller;
diff --git a/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt
new file mode 100644
index 000000000000..1ce4e46bcbb7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt
@@ -0,0 +1,18 @@
+Bindings, specific for the sh_mobile_ceu_camera.c driver:
+ - compatible: Should be "renesas,sh-mobile-ceu"
+ - reg: register base and size
+ - interrupts: the interrupt number
+ - interrupt-parent: the interrupt controller
+ - renesas,max-width: maximum image width, supported on this SoC
+ - renesas,max-height: maximum image height, supported on this SoC
+
+Example:
+
+ceu0: ceu@0xfe910000 {
+	compatible = "renesas,sh-mobile-ceu";
+	reg = <0xfe910000 0xa0>;
+	interrupt-parent = <&intcs>;
+	interrupts = <0x880>;
+	renesas,max-width = <8188>;
+	renesas,max-height = <8188>;
+};
diff --git a/Documentation/devicetree/bindings/metag/meta.txt b/Documentation/devicetree/bindings/metag/meta.txt
new file mode 100644
index 000000000000..f4457f57ab08
--- /dev/null
+++ b/Documentation/devicetree/bindings/metag/meta.txt
@@ -0,0 +1,30 @@
+* Meta Processor Binding
+
+This binding specifies what properties must be available in the device tree
+representation of a Meta Processor Core, which is the root node in the tree.
+
+Required properties:
+
+    - compatible: Specifies the compatibility list for the Meta processor.
+      The type shall be <string> and the value shall include "img,meta".
+
+Optional properties:
+
+    - clocks: Clock consumer specifiers as described in
+      Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+    - clock-names: Clock consumer names as described in
+      Documentation/devicetree/bindings/clock/clock-bindings.txt.
+
+Clocks are identified by name. Valid clocks are:
+
+    - "core": The Meta core clock from which the Meta timers are derived.
+
+* Examples
+
+/ {
+	compatible = "toumaz,tz1090", "img,meta";
+
+	clocks = <&meta_core_clk>;
+	clock-names = "core";
+};
diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt
new file mode 100644
index 000000000000..23a3650ff2a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max8998.txt
@@ -0,0 +1,119 @@
+* Maxim MAX8998, National/TI LP3974 multi-function device
+
+The Maxim MAX8998 is a multi-function device which includes voltage/current
+regulators, real time clock, battery charging controller and several
+other sub-blocks. It is interfaced using an I2C interface. Each sub-block
+is addressed by the host system using different i2c slave address.
+
+PMIC sub-block
+--------------
+
+The PMIC sub-block contains a number of voltage and current regulators,
+with controllable parameters and dynamic voltage scaling capability.
+In addition, it includes a real time clock and battery charging controller
+as well. It is accessible at I2C address 0x66.
+
+Required properties:
+- compatible: Should be one of the following:
+    - "maxim,max8998" for Maxim MAX8998
+    - "national,lp3974" or "ti,lp3974" for National/TI LP3974.
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+  the interrupts from MAX8998 are routed to.
+- interrupts: Interrupt specifiers for two interrupt sources.
+  - First interrupt specifier is for main interrupt.
+  - Second interrupt specifier is for power-on/-off interrupt.
+- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used
+  for buck 1 dvs. The format of the gpio specifier depends on the gpio
+  controller.
+- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used
+  for buck 2 dvs. The format of the gpio specifier depends on the gpio
+  controller.
+- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from
+  the possible 4 options selectable by the dvs gpios. The value of this
+  property should be 0, 1, 2 or 3. If not specified or out of range,
+  a default value of 0 is taken.
+- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from
+  the possible 2 options selectable by the dvs gpios. The value of this
+  property should be 0 or 1. If not specified or out of range, a default
+  value of 0 is taken.
+- max8998,pmic-buck-voltage-lock: If present, disallows changing of
+  preprogrammed buck dvfs voltages.
+
+Additional properties required if max8998,pmic-buck1-dvs-gpios is defined:
+- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts
+  for buck1 regulator that can be selected using dvs gpio.
+
+Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
+- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
+  for buck2 regulator that can be selected using dvs gpio.
+
+Regulators: All the regulators of MAX8998 to be instantiated shall be
+listed in a child node named 'regulators'. Each regulator is represented
+by a child node of the 'regulators' node.
+
+	regulator-name {
+		/* standard regulator bindings here */
+	};
+
+Following regulators of the MAX8998 PMIC block are supported. Note that
+the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK
+number as described in MAX8998 datasheet.
+
+	- LDOn
+		  - valid values for n are 2 to 17
+		  - Example: LDO2, LDO10, LDO17
+	- BUCKn
+		  - valid values for n are 1 to 4.
+		  - Example: BUCK1, BUCK2, BUCK3, BUCK4
+
+	- ENVICHG: Battery Charging Current Monitor Output. This is a fixed
+		   voltage type regulator
+
+	- ESAFEOUT1: (ldo19)
+	- ESAFEOUT2: (ld020)
+
+Standard regulator bindings are used inside regulator subnodes. Check
+  Documentation/devicetree/bindings/regulator/regulator.txt
+for more details.
+
+Example:
+
+	pmic@66 {
+		compatible = "maxim,max8998-pmic";
+		reg = <0x66>;
+		interrupt-parent = <&wakeup_eint>;
+		interrupts = <4 0>, <3 0>;
+
+		/* Buck 1 DVS settings */
+		max8998,pmic-buck1-default-dvs-idx = <0>;
+		max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
+					       <&gpx0 1 1 0 0>; /* SET2 */
+		max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+						 <1000000>, <950000>;
+
+		/* Buck 2 DVS settings */
+		max8998,pmic-buck2-default-dvs-idx = <0>;
+		max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
+		max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
+
+		/* Regulators to instantiate */
+		regulators {
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_ARM_1.2V";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
new file mode 100644
index 000000000000..8e15ec35ac99
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
@@ -0,0 +1,28 @@
+Texas Instruments TWL family (twl4030) reset and power management module
+
+The power management module inside the TWL family provides several facilities
+to control the power resources, including power scripts. For now, the
+binding only supports the complete shutdown of the system after poweroff.
+
+Required properties:
+- compatible : must be "ti,twl4030-power"
+
+Optional properties:
+- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or
+		   SLEEP-to-OFF transition when the system poweroffs.
+
+Example:
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_power: power {
+			compatible = "ti,twl4030-power";
+			ti,use_poweroff;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index 85aada2263d5..458b57f199af 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -28,6 +28,7 @@ Optional properties:
 - cap-mmc-highspeed: MMC high-speed timing is supported
 - cap-power-off-card: powering off the card is safe
 - cap-sdio-irq: enable SDIO IRQ signalling on this interface
+- full-pwr-cycle: full power cycle of the card is supported
 
 *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
 polarity properties, we have to fix the meaning of the "normal" and "inverted"
diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
new file mode 100644
index 000000000000..8a3d91d47b6a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
@@ -0,0 +1,23 @@
+* Rockchip specific extensions to the Synopsis Designware Mobile
+  Storage Host Controller
+
+The Synopsis designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsis dw mshc controller properties described
+by synopsis-dw-mshc.txt and the properties used by the Rockchip specific
+extensions to the Synopsis Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+	- "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following
+
+Example:
+
+	rkdwmmc0@12200000 {
+		compatible = "rockchip,rk2928-dw-mshc";
+		reg = <0x12200000 0x1000>;
+		interrupts = <0 75 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
index 1180d7814af8..cdcebea9c6f5 100644
--- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
@@ -39,6 +39,19 @@ Required Properties:
 
 Optional properties:
 
+* clocks: from common clock binding: handle to biu and ciu clocks for the
+  bus interface unit clock and the card interface unit clock.
+
+* clock-names: from common clock binding: Shall be "biu" and "ciu".
+  If the biu clock is missing we'll simply skip enabling it.  If the
+  ciu clock is missing we'll just assume that the clock is running at
+  clock-frequency.  It is an error to omit both the ciu clock and the
+  clock-frequency.
+
+* clock-frequency: should be the frequency (in Hz) of the ciu clock.  If this
+  is specified and the ciu clock is specified then we'll try to set the ciu
+  clock to this at probe time.
+
 * num-slots: specifies the number of slots supported by the controller.
   The number of physical slots actually used could be equal or less than the
   value specified by num-slots. If this property is not specified, the value
@@ -55,6 +68,9 @@ Optional properties:
 
 * broken-cd: as documented in mmc core bindings.
 
+* vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
+  specified we'll defer probe until we can find this regulator.
+
 Aliases:
 
 - All the MSHC controller nodes should be represented in the aliases node using
@@ -67,6 +83,8 @@ board specific portions as listed below.
 
 	dwmmc0@12200000 {
 		compatible = "snps,dw-mshc";
+		clocks = <&clock 351>, <&clock 132>;
+		clock-names = "biu", "ciu";
 		reg = <0x12200000 0x1000>;
 		interrupts = <0 75 0>;
 		#address-cells = <1>;
@@ -74,11 +92,13 @@ board specific portions as listed below.
 	};
 
 	dwmmc0@12200000 {
+		clock-frequency = <400000000>;
 		num-slots = <1>;
 		supports-highspeed;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
+		vmmc-supply = <&buck8>;
 
 		slot@0 {
 			reg = <0>;
diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt
new file mode 100644
index 000000000000..b90bfcd138ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt
@@ -0,0 +1,22 @@
+* Allwinner EMAC ethernet controller
+
+Required properties:
+- compatible: should be "allwinner,sun4i-emac".
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+- phy: A phandle to a phy node defining the PHY address (as the reg
+  property, a single integer).
+- clocks: A phandle to the reference clock for this device
+
+Optional properties:
+- (local-)mac-address: mac address to be used by this driver
+
+Example:
+
+emac: ethernet@01c0b000 {
+       compatible = "allwinner,sun4i-emac";
+       reg = <0x01c0b000 0x1000>;
+       interrupts = <55>;
+       clocks = <&ahb_gates 17>;
+       phy = <&phy0>;
+};
diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt
new file mode 100644
index 000000000000..00b9f9a3ec1d
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt
@@ -0,0 +1,26 @@
+* Allwinner A10 MDIO Ethernet Controller interface
+
+Required properties:
+- compatible: should be "allwinner,sun4i-mdio".
+- reg: address and length of the register set for the device.
+
+Optional properties:
+- phy-supply: phandle to a regulator if the PHY needs one
+
+Example at the SoC level:
+mdio@01c0b080 {
+	compatible = "allwinner,sun4i-mdio";
+	reg = <0x01c0b080 0x14>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+
+And at the board level:
+
+mdio@01c0b080 {
+	phy-supply = <&reg_emac_3v3>;
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt
new file mode 100644
index 000000000000..bcbc3f009158
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/arc_emac.txt
@@ -0,0 +1,38 @@
+* Synopsys ARC EMAC 10/100 Ethernet driver (EMAC)
+
+Required properties:
+- compatible: Should be "snps,arc-emac"
+- reg: Address and length of the register set for the device
+- interrupts: Should contain the EMAC interrupts
+- clock-frequency: CPU frequency. It is needed to calculate and set polling
+period of EMAC.
+- max-speed: Maximum supported data-rate in Mbit/s. In some HW configurations
+bandwidth of external memory controller might be a limiting factor. That's why
+it's required to specify which data-rate is supported on current SoC or FPGA.
+For example if only 10 Mbit/s is supported (10BASE-T) set "10". If 100 Mbit/s is
+supported (100BASE-TX) set "100".
+- phy: PHY device attached to the EMAC via MDIO bus
+
+Child nodes of the driver are the individual PHY devices connected to the
+MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus.
+
+Optional properties:
+- mac-address: 6 bytes, mac address
+
+Examples:
+
+	ethernet@c0fc2000 {
+		compatible = "snps,arc-emac";
+		reg = <0xc0fc2000 0x3c>;
+		interrupts = <6>;
+		mac-address = [ 00 11 22 33 44 55 ];
+		clock-frequency = <80000000>;
+		max-speed = <100>;
+		phy = <&phy0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@0 {
+			reg = <1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
index 8ff324eaa889..56d6cc336e1c 100644
--- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
+++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
@@ -16,6 +16,8 @@ Optional properties:
 
 - clock-frequency : The oscillator frequency driving the flexcan device
 
+- xceiver-supply: Regulator that powers the CAN transceiver
+
 Example:
 
 	can@1c000 {
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 4f2ca6b4a182..05d660e4ac64 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -28,6 +28,8 @@ Optional properties:
 Slave Properties:
 Required properties:
 - phy_id		: Specifies slave phy id
+- phy-mode		: The interface between the SoC and the PHY (a string
+			  that of_get_phy_mode() can understand)
 - mac-address		: Specifies slave MAC address
 
 Optional properties:
@@ -58,11 +60,13 @@ Examples:
 		cpts_clock_shift = <29>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
 		cpsw_emac1: slave@1 {
 			phy_id = <&davinci_mdio>, <1>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
@@ -84,11 +88,13 @@ Examples:
 		cpts_clock_shift = <29>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
 		cpsw_emac1: slave@1 {
 			phy_id = <&davinci_mdio>, <1>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt
new file mode 100644
index 000000000000..2d39c990e641
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt
@@ -0,0 +1,26 @@
+Davicom DM9000 Fast Ethernet controller
+
+Required properties:
+- compatible = "davicom,dm9000";
+- reg : physical addresses and sizes of registers, must contain 2 entries:
+    first entry : address register,
+    second entry : data register.
+- interrupt-parent : interrupt controller to which the device is connected
+- interrupts : interrupt specifier specific to interrupt controller
+
+Optional properties:
+- local-mac-address : A bytestring of 6 bytes specifying Ethernet MAC address
+    to use (from firmware or bootloader)
+- davicom,no-eeprom : Configuration EEPROM is not available
+- davicom,ext-phy : Use external PHY
+
+Example:
+
+	ethernet@18000000 {
+		compatible = "davicom,dm9000";
+		reg = <0x18000000 0x2 0x18000004 0x2>;
+		interrupt-parent = <&gpn>;
+		interrupts = <7 4>;
+		local-mac-address = [00 00 de ad be ef];
+		davicom,no-eeprom;
+	};
diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt
new file mode 100644
index 000000000000..a73b79f227e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt
@@ -0,0 +1,85 @@
+Marvell Orion/Discovery ethernet controller
+=============================================
+
+The Marvell Discovery ethernet controller can be found on Marvell Orion SoCs
+(Kirkwood, Dove, Orion5x, and Discovery Innovation) and as part of Marvell
+Discovery system controller chips (mv64[345]60).
+
+The Discovery ethernet controller is described with two levels of nodes. The
+first level describes the ethernet controller itself and the second level
+describes up to 3 ethernet port nodes within that controller. The reason for
+the multiple levels is that the port registers are interleaved within a single
+set of controller registers. Each port node describes port-specific properties.
+
+Note: The above separation is only true for Discovery system controllers.
+For Orion SoCs we stick to the separation, although there each controller has
+only one port associated. Multiple ports are implemented as multiple single-port
+controllers. As Kirkwood has some issues with proper initialization after reset,
+an extra compatible string is added for it.
+
+* Ethernet controller node
+
+Required controller properties:
+ - #address-cells: shall be 1.
+ - #size-cells: shall be 0.
+ - compatible: shall be one of "marvell,orion-eth", "marvell,kirkwood-eth".
+ - reg: address and length of the controller registers.
+
+Optional controller properties:
+ - clocks: phandle reference to the controller clock.
+ - marvell,tx-checksum-limit: max tx packet size for hardware checksum.
+
+* Ethernet port node
+
+Required port properties:
+ - device_type: shall be "network".
+ - compatible: shall be one of "marvell,orion-eth-port",
+      "marvell,kirkwood-eth-port".
+ - reg: port number relative to ethernet controller, shall be 0, 1, or 2.
+ - interrupts: port interrupt.
+ - local-mac-address: 6 bytes MAC address.
+
+Optional port properties:
+ - marvell,tx-queue-size: size of the transmit ring buffer.
+ - marvell,tx-sram-addr: address of transmit descriptor buffer located in SRAM.
+ - marvell,tx-sram-size: size of transmit descriptor buffer located in SRAM.
+ - marvell,rx-queue-size: size of the receive ring buffer.
+ - marvell,rx-sram-addr: address of receive descriptor buffer located in SRAM.
+ - marvell,rx-sram-size: size of receive descriptor buffer located in SRAM.
+
+and
+
+ - phy-handle: phandle reference to ethernet PHY.
+
+or
+
+ - speed: port speed if no PHY connected.
+ - duplex: port mode if no PHY connected.
+
+* Node example:
+
+mdio-bus {
+	...
+	ethphy: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		...
+	};
+};
+
+eth: ethernet-controller@72000 {
+	compatible = "marvell,orion-eth";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x72000 0x2000>;
+	clocks = <&gate_clk 2>;
+	marvell,tx-checksum-limit = <1600>;
+
+	ethernet@0 {
+		device_type = "network";
+		compatible = "marvell,orion-eth-port";
+		reg = <0>;
+		interrupts = <29>;
+		phy-handle = <&ethphy>;
+		local-mac-address = [00 00 00 00 00 00];
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt
new file mode 100644
index 000000000000..11ace3c3d805
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt
@@ -0,0 +1,9 @@
+Micrel KS8851 Ethernet mac
+
+Required properties:
+- compatible = "micrel,ks8851-ml" of parallel interface
+- reg : 2 physical address and size of registers for data and command
+- interrupts : interrupt connection
+
+Optional properties:
+- local-mac-address : Ethernet mac address to use
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index 060bbf098ef3..261c563b5f06 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -12,6 +12,16 @@ Required properties:
   property
 - phy-mode: String, operation mode of the PHY interface.
   Supported values are: "mii", "rmii", "gmii", "rgmii".
+- snps,phy-addr		phy address to connect to.
+- snps,reset-gpio 	gpio number for phy reset.
+- snps,reset-active-low boolean flag to indicate if phy reset is active low.
+- snps,reset-delays-us  is triplet of delays
+	The 1st cell is reset pre-delay in micro seconds.
+	The 2nd cell is reset pulse in micro seconds.
+	The 3rd cell is reset post-delay in micro seconds.
+- snps,pbl		Programmable Burst Length
+- snps,fixed-burst	Program the DMA to use the fixed burst mode
+- snps,mixed-burst	Program the DMA to use the mixed burst mode
 
 Optional properties:
 - mac-address: 6 bytes, mac address
diff --git a/Documentation/devicetree/bindings/net/via-velocity.txt b/Documentation/devicetree/bindings/net/via-velocity.txt
new file mode 100644
index 000000000000..b3db469b1ad7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/via-velocity.txt
@@ -0,0 +1,20 @@
+* VIA Velocity 10/100/1000 Network Controller
+
+Required properties:
+- compatible : Should be "via,velocity-vt6110"
+- reg : Address and length of the io space
+- interrupts : Should contain the controller interrupt line
+
+Optional properties:
+- no-eeprom : PCI network cards use an external EEPROM to store data. Embedded
+	devices quite often set this data in uboot and do not provide an eeprom.
+	Specify this option if you have no external eeprom.
+
+Examples:
+
+eth0@d8004000 {
+	compatible = "via,velocity-vt6110";
+	reg = <0xd8004000 0x400>;
+	interrupts = <10>;
+	no-eeprom;
+};
diff --git a/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt
new file mode 100644
index 000000000000..2246bc5c874b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt
@@ -0,0 +1,44 @@
+Binding for TI/National Semiconductor LP8727 Charger
+
+Required properties:
+- compatible: "ti,lp8727"
+- reg: I2C slave address 27h
+
+Optional properties:
+- interrupt-parent: interrupt controller node (see interrupt binding[0])
+- interrupts: interrupt specifier (see interrupt binding[0])
+- debounce-ms: interrupt debounce time. (u32)
+
+AC and USB charging parameters
+- charger-type: "ac" or "usb" (string)
+- eoc-level: value of 'enum lp8727_eoc_level' (u8)
+- charging-current: value of 'enum lp8727_ichg' (u8)
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Example)
+
+lp8727@27 {
+	compatible = "ti,lp8727";
+	reg = <0x27>;
+
+	/* GPIO 134 is used for LP8728 interrupt pin */
+	interrupt-parent = <&gpio5>; 	/* base = 128 */
+	interrupts = <6 0x2>;		/* offset = 6, falling edge type */
+
+	debounce-ms = <300>;
+
+	/* AC charger: 5% EOC and 500mA charging current */
+	ac {
+		charger-type = "ac";
+		eoc-level = /bits/ 8 <0>;
+		charging-current = /bits/ 8 <4>;
+	};
+
+	/* USB charger: 10% EOC and 400mA charging current */
+	usb {
+		charger-type = "usb";
+		eoc-level = /bits/ 8 <1>;
+		charging-current = /bits/ 8 <2>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
new file mode 100644
index 000000000000..1e3dfe7a4894
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
@@ -0,0 +1,27 @@
+NXP PCA9685 16-channel 12-bit PWM LED controller
+================================================
+
+Required properties:
+  - compatible: "nxp,pca9685-pwm"
+  - #pwm-cells: should be 2. The first cell specifies the per-chip index
+    of the PWM to use and the second cell is the period in nanoseconds.
+    The index 16 is the ALLCALL channel, that sets all PWM channels at the same
+    time.
+
+Optional properties:
+  - invert (bool): boolean to enable inverted logic
+  - open-drain (bool): boolean to configure outputs with open-drain structure;
+		       if omitted use totem-pole structure
+
+Example:
+
+For LEDs that are directly connected to the PCA, the following setting is
+applicable:
+
+pca: pca@41 {
+	compatible = "nxp,pca9685-pwm";
+	#pwm-cells = <2>;
+	reg = <0x41>;
+	invert;
+	open-drain;
+};
diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
index 9e5e51d78868..5c186a7a77ba 100644
--- a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
@@ -1,6 +1,6 @@
 * Maxim MAX8997 Voltage and Current Regulator
 
-The Maxim MAX8997 is a multi-function device which includes volatage and
+The Maxim MAX8997 is a multi-function device which includes voltage and
 current regulators, rtc, charger controller and other sub-blocks. It is
 interfaced to the host controller using a i2c interface. Each sub-block is
 addressed by the host system using different i2c slave address. This document
diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
index a35ff99003a5..d1660a90fc06 100644
--- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
@@ -1,6 +1,6 @@
 * Samsung S5M8767 Voltage and Current Regulator
 
-The Samsung S5M8767 is a multi-function device which includes volatage and
+The Samsung S5M8767 is a multi-function device which includes voltage and
 current regulators, rtc, charger controller and other sub-blocks. It is
 interfaced to the host controller using a i2c interface. Each sub-block is
 addressed by the host system using different i2c slave address. This document
@@ -103,13 +103,13 @@ Example:
 
 		s5m8767,pmic-buck-default-dvs-idx = <0>;
 
-		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */
-						 <&gpx0 1 1 0 0>, /* DVS2 */
-						 <&gpx0 2 1 0 0>; /* DVS3 */
+		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
+						 <&gpx0 1 0>, /* DVS2 */
+						 <&gpx0 2 0>; /* DVS3 */
 
-		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */
-						<&gpx2 4 1 0 0>, /* SET2 */
-						<&gpx2 5 1 0 0>; /* SET3 */
+		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
+						<&gpx2 4 0>, /* SET2 */
+						<&gpx2 5 0>; /* SET3 */
 
 		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
 						 <1250000>, <1200000>,
diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
index 658749b90b97..75b0c1669504 100644
--- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
@@ -18,20 +18,20 @@ For twl6030 regulators/LDOs
   - "ti,twl6030-vdd1" for VDD1 SMPS
   - "ti,twl6030-vdd2" for VDD2 SMPS
   - "ti,twl6030-vdd3" for VDD3 SMPS
-For twl6025 regulators/LDOs
+For twl6032 regulators/LDOs
 - compatible:
-  - "ti,twl6025-ldo1" for LDO1 LDO
-  - "ti,twl6025-ldo2" for LDO2 LDO
-  - "ti,twl6025-ldo3" for LDO3 LDO
-  - "ti,twl6025-ldo4" for LDO4 LDO
-  - "ti,twl6025-ldo5" for LDO5 LDO
-  - "ti,twl6025-ldo6" for LDO6 LDO
-  - "ti,twl6025-ldo7" for LDO7 LDO
-  - "ti,twl6025-ldoln" for LDOLN LDO
-  - "ti,twl6025-ldousb" for LDOUSB LDO
-  - "ti,twl6025-smps3" for SMPS3 SMPS
-  - "ti,twl6025-smps4" for SMPS4 SMPS
-  - "ti,twl6025-vio" for VIO SMPS
+  - "ti,twl6032-ldo1" for LDO1 LDO
+  - "ti,twl6032-ldo2" for LDO2 LDO
+  - "ti,twl6032-ldo3" for LDO3 LDO
+  - "ti,twl6032-ldo4" for LDO4 LDO
+  - "ti,twl6032-ldo5" for LDO5 LDO
+  - "ti,twl6032-ldo6" for LDO6 LDO
+  - "ti,twl6032-ldo7" for LDO7 LDO
+  - "ti,twl6032-ldoln" for LDOLN LDO
+  - "ti,twl6032-ldousb" for LDOUSB LDO
+  - "ti,twl6032-smps3" for SMPS3 SMPS
+  - "ti,twl6032-smps4" for SMPS4 SMPS
+  - "ti,twl6032-vio" for VIO SMPS
 For twl4030 regulators/LDOs
 - compatible:
   - "ti,twl4030-vaux1" for VAUX1 LDO
diff --git a/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt b/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt
new file mode 100644
index 000000000000..0c9222d27fae
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt
@@ -0,0 +1,74 @@
+* Texas Instrument OMAP SCM bandgap bindings
+
+In the System Control Module, OMAP supplies a voltage reference
+and a temperature sensor feature that are gathered in the band
+gap voltage and temperature sensor (VBGAPTS) module. The band
+gap provides current and voltage reference for its internal
+circuits and other analog IP blocks. The analog-to-digital
+converter (ADC) produces an output value that is proportional
+to the silicon temperature.
+
+Required properties:
+- compatible : Should be:
+  - "ti,omap4430-bandgap" : for OMAP4430 bandgap
+  - "ti,omap4460-bandgap" : for OMAP4460 bandgap
+  - "ti,omap4470-bandgap" : for OMAP4470 bandgap
+  - "ti,omap5430-bandgap" : for OMAP5430 bandgap
+- interrupts : this entry should indicate which interrupt line
+the talert signal is routed to;
+Specific:
+- gpios : this entry should be used to inform which GPIO
+line the tshut signal is routed to. The informed GPIO will
+be treated as an IRQ;
+- regs : this entry must also be specified and it is specific
+to each bandgap version, because the mapping may change from
+soc to soc, apart of depending on available features.
+
+Example:
+OMAP4430:
+bandgap {
+	reg = <0x4a002260 0x4 0x4a00232C 0x4>;
+	compatible = "ti,omap4430-bandgap";
+};
+
+OMAP4460:
+bandgap {
+	reg = <0x4a002260 0x4
+		0x4a00232C 0x4
+		0x4a002378 0x18>;
+	compatible = "ti,omap4460-bandgap";
+	interrupts = <0 126 4>; /* talert */
+	gpios = <&gpio3 22 0>; /* tshut */
+};
+
+OMAP4470:
+bandgap {
+	reg = <0x4a002260 0x4
+		0x4a00232C 0x4
+		0x4a002378 0x18>;
+	compatible = "ti,omap4470-bandgap";
+	interrupts = <0 126 4>; /* talert */
+	gpios = <&gpio3 22 0>; /* tshut */
+};
+
+OMAP5430:
+bandgap {
+	reg = <0x4a0021e0 0xc
+		0x4a00232c 0xc
+		0x4a002380 0x2c
+		0x4a0023C0 0x3c>;
+	compatible = "ti,omap5430-bandgap";
+	interrupts = <0 126 4>; /* talert */
+};
+
+DRA752:
+bandgap {
+	reg = <0x4a0021e0 0xc
+		0x4a00232c 0xc
+		0x4a002380 0x2c
+		0x4a0023C0 0x3c
+		0x4a002564 0x8
+		0x4a002574 0x50>;
+	compatible = "ti,dra752-bandgap";
+	interrupts = <0 126 4>; /* talert */
+};
diff --git a/Documentation/devicetree/bindings/timer/lsi,zevio-timer.txt b/Documentation/devicetree/bindings/timer/lsi,zevio-timer.txt
new file mode 100644
index 000000000000..b2d07ad90e9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/lsi,zevio-timer.txt
@@ -0,0 +1,33 @@
+TI-NSPIRE timer
+
+Required properties:
+
+- compatible : should be "lsi,zevio-timer".
+- reg : The physical base address and size of the timer (always first).
+- clocks: phandle to the source clock.
+
+Optional properties:
+
+- interrupts : The interrupt number of the first timer.
+- reg : The interrupt acknowledgement registers
+	(always after timer base address)
+
+If any of the optional properties are not given, the timer is added as a
+clock-source only.
+
+Example:
+
+timer {
+	compatible = "lsi,zevio-timer";
+	reg = <0x900D0000 0x1000>, <0x900A0020 0x8>;
+	interrupts = <19>;
+	clocks = <&timer_clk>;
+};
+
+Example (no clock-events):
+
+timer {
+	compatible = "lsi,zevio-timer";
+	reg = <0x900D0000 0x1000>;
+	clocks = <&timer_clk>;
+};
diff --git a/Documentation/devicetree/bindings/timer/marvell,orion-timer.txt b/Documentation/devicetree/bindings/timer/marvell,orion-timer.txt
new file mode 100644
index 000000000000..62bb8260cf6a
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/marvell,orion-timer.txt
@@ -0,0 +1,17 @@
+Marvell Orion SoC timer
+
+Required properties:
+- compatible: shall be "marvell,orion-timer"
+- reg: base address of the timer register starting with TIMERS CONTROL register
+- interrupt-parent: phandle of the bridge interrupt controller
+- interrupts: should contain the interrupts for Timer0 and Timer1
+- clocks: phandle of timer reference clock (tclk)
+
+Example:
+	timer: timer {
+		compatible = "marvell,orion-timer";
+		reg = <0x20300 0x20>;
+		interrupt-parent = <&bridge_intc>;
+		interrupts = <1>, <2>;
+		clocks = <&core_clk 0>;
+	};
diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
index 36b9aede3f40..0aee0ad3f035 100644
--- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt
@@ -8,7 +8,7 @@ TWL6030 USB COMPARATOR
    usb interrupt number that raises VBUS interrupts when the controller has to
    act as device
  - usb-supply : phandle to the regulator device tree node. It should be vusb
-   if it is twl6030 or ldousb if it is twl6025 subclass.
+   if it is twl6030 or ldousb if it is twl6032 subclass.
 
 twl6030-usb {
 	compatible = "ti,twl6030-usb";
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index db0457d61682..366ce9b87240 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -18,6 +18,7 @@ chrp	Common Hardware Reference Platform
 cirrus	Cirrus Logic, Inc.
 cortina	Cortina Systems, Inc.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
+davicom	DAVICOM Semiconductor, Inc.
 denx	Denx Software Engineering
 emmicro	EM Microelectronic
 epson	Seiko Epson Corp.
@@ -25,6 +26,7 @@ est	ESTeem Wireless Modems
 fsl	Freescale Semiconductor
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
+hisilicon	Hisilicon Limited.
 hp	Hewlett Packard
 ibm	International Business Machines (IBM)
 idt	Integrated Device Technologies, Inc.
@@ -42,6 +44,7 @@ nxp	NXP Semiconductors
 onnn	ON Semiconductor Corp.
 picochip	Picochip Ltd
 powervr	PowerVR (deprecated, use img)
+qca	Qualcomm Atheros, Inc.
 qcom	Qualcomm, Inc.
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
@@ -58,6 +61,7 @@ snps 	Synopsys, Inc.
 st	STMicroelectronics
 ste	ST-Ericsson
 stericsson	ST-Ericsson
+toumaz	Toumaz
 ti	Texas Instruments
 toshiba	Toshiba Corporation
 v3	V3 Semiconductor
diff --git a/Documentation/devicetree/bindings/video/display-timing.txt b/Documentation/devicetree/bindings/video/display-timing.txt
index 150038552bc3..e1d4a0b59612 100644
--- a/Documentation/devicetree/bindings/video/display-timing.txt
+++ b/Documentation/devicetree/bindings/video/display-timing.txt
@@ -34,6 +34,7 @@ optional properties:
 			- ignored     = ignored
  - interlaced (bool): boolean to enable interlaced mode
  - doublescan (bool): boolean to enable doublescan mode
+ - doubleclk (bool): boolean to enable doubleclock mode
 
 All the optional properties that are not bool follow the following logic:
     <1>: high active
diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
index 589edee37394..323983be3c30 100644
--- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt
+++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt
@@ -1,22 +1,23 @@
 Device-Tree bindings for drm hdmi driver
 
 Required properties:
-- compatible: value should be "samsung,exynos5-hdmi".
+- compatible: value should be one among the following:
+	1) "samsung,exynos5-hdmi" <DEPRECATED>
+	2) "samsung,exynos4210-hdmi"
+	3) "samsung,exynos4212-hdmi"
 - reg: physical base address of the hdmi and length of memory mapped
 	region.
 - interrupts: interrupt number to the cpu.
 - hpd-gpio: following information about the hotplug gpio pin.
 	a) phandle of the gpio controller node.
 	b) pin number within the gpio controller.
-	c) pin function mode.
-	d) optional flags and pull up/down.
-	e) drive strength.
+	c) optional flags and pull up/down.
 
 Example:
 
 	hdmi {
-		compatible = "samsung,exynos5-hdmi";
+		compatible = "samsung,exynos4212-hdmi";
 		reg = <0x14530000 0x100000>;
 		interrupts = <0 95 0>;
-		hpd-gpio = <&gpx3 7 0xf 1 3>;
+		hpd-gpio = <&gpx3 7 1>;
 	};
diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt
index fa166d945809..41eee971562b 100644
--- a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt
+++ b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt
@@ -1,12 +1,15 @@
 Device-Tree bindings for hdmiddc driver
 
 Required properties:
-- compatible: value should be "samsung,exynos5-hdmiddc".
+- compatible: value should be one of the following
+	1) "samsung,exynos5-hdmiddc" <DEPRECATED>
+	2) "samsung,exynos4210-hdmiddc"
+
 - reg: I2C address of the hdmiddc device.
 
 Example:
 
 	hdmiddc {
-		compatible = "samsung,exynos5-hdmiddc";
+		compatible = "samsung,exynos4210-hdmiddc";
 		reg = <0x50>;
 	};
diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt
index 858f4f9b902f..162f641f7639 100644
--- a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt
+++ b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt
@@ -1,12 +1,15 @@
 Device-Tree bindings for hdmiphy driver
 
 Required properties:
-- compatible: value should be "samsung,exynos5-hdmiphy".
+- compatible: value should be one of the following:
+	1) "samsung,exynos5-hdmiphy" <DEPRECATED>
+	2) "samsung,exynos4210-hdmiphy".
+	3) "samsung,exynos4212-hdmiphy".
 - reg: I2C address of the hdmiphy device.
 
 Example:
 
 	hdmiphy {
-		compatible = "samsung,exynos5-hdmiphy";
+		compatible = "samsung,exynos4210-hdmiphy";
 		reg = <0x38>;
 	};
diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt
index 9b2ea0343566..3334b0a8e343 100644
--- a/Documentation/devicetree/bindings/video/exynos_mixer.txt
+++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt
@@ -1,7 +1,12 @@
 Device-Tree bindings for mixer driver
 
 Required properties:
-- compatible: value should be "samsung,exynos5-mixer".
+- compatible: value should be one of the following:
+	1) "samsung,exynos5-mixer" <DEPRECATED>
+	2) "samsung,exynos4210-mixer"
+	3) "samsung,exynos5250-mixer"
+	4) "samsung,exynos5420-mixer"
+
 - reg: physical base address of the mixer and length of memory mapped
 	region.
 - interrupts: interrupt number to the cpu.
@@ -9,7 +14,7 @@ Required properties:
 Example:
 
 	mixer {
-		compatible = "samsung,exynos5-mixer";
+		compatible = "samsung,exynos5250-mixer";
 		reg = <0x14450000 0x10000>;
 		interrupts = <0 94 0>;
 	};
diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
new file mode 100644
index 000000000000..46da08db186a
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt
@@ -0,0 +1,51 @@
+Freescale imx21 Framebuffer
+
+This framebuffer driver supports devices imx1, imx21, imx25, and imx27.
+
+Required properties:
+- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : One interrupt of the fb dev
+
+Required nodes:
+- display: Phandle to a display node as described in
+	Documentation/devicetree/bindings/video/display-timing.txt
+	Additional, the display node has to define properties:
+	- bits-per-pixel: Bits per pixel
+	- fsl,pcr: LCDC PCR value
+
+Optional properties:
+- fsl,dmacr: DMA Control Register value. This is optional. By default, the
+	register is not modified as recommended by the datasheet.
+- fsl,lscr1: LCDC Sharp Configuration Register value.
+
+Example:
+
+	imxfb: fb@10021000 {
+		compatible = "fsl,imx21-fb";
+		interrupts = <61>;
+		reg = <0x10021000 0x1000>;
+		display = <&display0>;
+	};
+
+	...
+
+	display0: display0 {
+		model = "Primeview-PD050VL1";
+		native-mode = <&timing_disp0>;
+		bits-per-pixel = <16>;
+		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
+		display-timings {
+			timing_disp0: 640x480 {
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <112>;
+				hfront-porch = <36>;
+				hsync-len = <32>;
+				vback-porch = <33>;
+				vfront-porch = <33>;
+				vsync-len = <2>;
+				clock-frequency = <25000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt
index 3d0060cff062..7a125427ff4b 100644
--- a/Documentation/devicetree/bindings/video/ssd1307fb.txt
+++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt
@@ -1,13 +1,17 @@
 * Solomon SSD1307 Framebuffer Driver
 
 Required properties:
-  - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for
-    now is i2c.
+  - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for
+    now is i2c, and the supported chips are ssd1306 and ssd1307.
   - reg: Should contain address of the controller on the I2C bus. Most likely
          0x3c or 0x3d
   - pwm: Should contain the pwm to use according to the OF device tree PWM
-         specification [0]
+         specification [0]. Only required for the ssd1307.
   - reset-gpios: Should contain the GPIO used to reset the OLED display
+  - solomon,height: Height in pixel of the screen driven by the controller
+  - solomon,width: Width in pixel of the screen driven by the controller
+  - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
+    mapped to.
 
 Optional properties:
   - reset-active-low: Is the reset gpio is active on physical low?
diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt
index d209366b4a69..f801d71de1cd 100644
--- a/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt
+++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt
@@ -5,9 +5,14 @@ Required properties:
 - compatible : should be "brcm,bcm2835-pm-wdt"
 - reg : Specifies base physical address and size of the registers.
 
+Optional properties:
+
+- timeout-sec   : Contains the watchdog timeout in seconds
+
 Example:
 
 watchdog {
 	compatible = "brcm,bcm2835-pm-wdt";
 	reg = <0x7e100000 0x28>;
+	timeout-sec = <10>;
 };