Merge branch 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata changes from Tejun Heo:
 "Except for a few, all the changes are for ahci platform drivers for
  the arm devices.  Nothing too interesting or dangerous.  There's one
  merge from libata/for-3.16-fixes to pull in dependent changes"

* 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
  ata: libahci: Silence compiler warning on 64-bit
  Documentation: bindings: document the sub-nodes AHCI bindings
  ata: ahci_platform: add a generic AHCI compatible
  ata: libahci: allow to use multiple PHYs
  ata: libahci_platform: move port_map parameters into the AHCI structure
  ahci: imx: add missing clk_disable_unprepare() on error in imx_sata_enable()
  ahci_xgene: Use correct OOB tunning parameters for APM X-Gene SoC AHCI SATA Host controller driver.
  ahci_xgene: Fix the watermark threshold for the APM X-Gene SATA host controller driver.
  ahci: st: Make of_device_id array const
  sata_sil24: Identify which card suffered IRQ status error
  ahci: st: Provide DT bindings for ST's SATA implementation
  ata: Add support for the Tegra124 SATA controller
  ata: ahci_platform: Increase AHCI_MAX_CLKS to 4
  of: Add NVIDIA Tegra SATA controller binding
  dt-bindings: ata: document ability to disable spread-spectrum clock
  ata: ahci_imx: add disable for spread-spectrum
  dt-bindings: ata: add ahci_imx electrical properties
  ata: ahci_imx: allow hardware parameters to be specified in DT
  dt-bindings: ata: create bindings for imx sata controller
  ata: pata_samsung_cf: removes s5pc100 related ata codes
  ...

4 files changed, 137 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
index c96d8dcf98fd..4ab09f2202d4 100644
--- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -3,28 +3,43 @@
 SATA nodes are defined to describe on-chip Serial ATA controllers.
 Each SATA controller should have its own node.
 
+It is possible, but not required, to represent each port as a sub-node.
+It allows to enable each port independently when dealing with multiple
+PHYs.
+
 Required properties:
 - compatible        : compatible string, one of:
   - "allwinner,sun4i-a10-ahci"
-  - "fsl,imx53-ahci"
-  - "fsl,imx6q-ahci"
   - "hisilicon,hisi-ahci"
   - "ibm,476gtr-ahci"
   - "marvell,armada-380-ahci"
   - "snps,dwc-ahci"
   - "snps,exynos5440-ahci"
   - "snps,spear-ahci"
+  - "generic-ahci"
 - interrupts        : <interrupt mapping for SATA IRQ>
 - reg               : <registers mapping>
 
+Please note that when using "generic-ahci" you must also specify a SoC specific
+compatible:
+	compatible = "manufacturer,soc-model-ahci", "generic-ahci";
+
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
 - clocks            : a list of phandle + clock specifier pairs
 - target-supply     : regulator for SATA target power
+- phys              : reference to the SATA PHY node
+- phy-names         : must be "sata-phy"
+
+Required properties when using sub-nodes:
+- #address-cells    : number of cells to encode an address
+- #size-cells       : number of cells representing the size of an address
+
+
+Sub-nodes required properties:
+- reg               : the port number
+- phys              : reference to the SATA PHY node
 
-"fsl,imx53-ahci", "fsl,imx6q-ahci" required properties:
-- clocks            : must contain the sata, sata_ref and ahb clocks
-- clock-names       : must contain "ahb" for the ahb clock
 
 Examples:
         sata@ffe08000 {
@@ -40,3 +55,23 @@ Examples:
 		clocks = <&pll6 0>, <&ahb_gates 25>;
 		target-supply = <&reg_ahci_5v>;
 	};
+
+With sub-nodes:
+	sata@f7e90000 {
+		compatible = "marvell,berlin2q-achi", "generic-ahci";
+		reg = <0xe90000 0x1000>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&chip CLKID_SATA>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sata0: sata-port@0 {
+			reg = <0>;
+			phys = <&sata_phy 0>;
+		};
+
+		sata1: sata-port@1 {
+			reg = <1>;
+			phys = <&sata_phy 1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt
new file mode 100644
index 000000000000..0574a77a0b9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/ahci-st.txt
@@ -0,0 +1,31 @@
+STMicroelectronics STi SATA controller
+
+This binding describes a SATA device.
+
+Required properties:
+ - compatible	   : Must be "st,sti-ahci"
+ - reg		   : Physical base addresses and length of register sets
+ - interrupts	   : Interrupt associated with the SATA device
+ - interrupt-names :   Associated name must be; "hostc"
+ - resets	   : The power-down and soft-reset lines of SATA IP
+ - reset-names	   :   Associated names must be; "pwr-dwn" and "sw-rst"
+ - clocks	   : The phandle for the clock
+ - clock-names	   :   Associated name must be; "ahci_clk"
+ - phys		   : The phandle for the PHY device
+ - phy-names	   :   Associated name must be; "ahci_phy"
+
+Example:
+
+	sata0: sata@fe380000 {
+		compatible      = "st,sti-ahci";
+		reg             = <0xfe380000 0x1000>;
+		interrupts      = <GIC_SPI 157 IRQ_TYPE_NONE>;
+		interrupt-names = "hostc";
+		phys	        = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>;
+		phy-names       = "ahci_phy";
+		resets	        = <&powerdown STIH416_SATA0_POWERDOWN>,
+				  <&softreset STIH416_SATA0_SOFTRESET>;
+		reset-names     = "pwr-dwn", "sw-rst";
+		clocks	        = <&clk_s_a0_ls CLK_ICN_REG>;
+		clock-names     = "ahci_clk";
+	};
diff --git a/Documentation/devicetree/bindings/ata/imx-sata.txt b/Documentation/devicetree/bindings/ata/imx-sata.txt
new file mode 100644
index 000000000000..fa511db18408
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/imx-sata.txt
@@ -0,0 +1,36 @@
+* Freescale i.MX AHCI SATA Controller
+
+The Freescale i.MX SATA controller mostly conforms to the AHCI interface
+with some special extensions at integration level.
+
+Required properties:
+- compatible : should be one of the following:
+   - "fsl,imx53-ahci" for i.MX53 SATA controller
+   - "fsl,imx6q-ahci" for i.MX6Q SATA controller
+- interrupts : interrupt mapping for SATA IRQ
+- reg : registers mapping
+- clocks : list of clock specifiers, must contain an entry for each
+  required entry in clock-names
+- clock-names : should include "sata", "sata_ref" and "ahb" entries
+
+Optional properties:
+- fsl,transmit-level-mV : transmit voltage level, in millivolts.
+- fsl,transmit-boost-mdB : transmit boost level, in milli-decibels
+- fsl,transmit-atten-16ths : transmit attenuation, in 16ths
+- fsl,receive-eq-mdB : receive equalisation, in milli-decibels
+  Please refer to the technical documentation or the driver source code
+  for the list of legal values for these options.
+- fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA
+  link.
+
+Examples:
+
+sata@02200000 {
+	compatible = "fsl,imx6q-ahci";
+	reg = <0x02200000 0x4000>;
+	interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks IMX6QDL_CLK_SATA>,
+		 <&clks IMX6QDL_CLK_SATA_REF_100M>,
+		 <&clks IMX6QDL_CLK_AHB>;
+	clock-names = "sata", "sata_ref", "ahb";
+};
diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt
new file mode 100644
index 000000000000..946f2072570b
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt
@@ -0,0 +1,30 @@
+Tegra124 SoC SATA AHCI controller
+
+Required properties :
+- compatible : "nvidia,tegra124-ahci".
+- reg : Should contain 2 entries:
+  - AHCI register set (SATA BAR5)
+  - SATA register set
+- interrupts : Defines the interrupt used by SATA
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - sata
+  - sata-oob
+  - cml1
+  - pll_e
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - sata
+  - sata-oob
+  - sata-cold
+- phys : Must contain an entry for each entry in phy-names.
+  See ../phy/phy-bindings.txt for details.
+- phy-names : Must include the following entries:
+  - sata-phy : XUSB PADCTL SATA PHY
+- hvdd-supply : Defines the SATA HVDD regulator
+- vddio-supply : Defines the SATA VDDIO regulator
+- avdd-supply : Defines the SATA AVDD regulator
+- target-5v-supply : Defines the SATA 5V power regulator
+- target-12v-supply : Defines the SATA 12V power regulator