Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq updates from Thomas Gleixner:
 "The interrupt brigade came up with the following updates:

   - Driver for the Marvell System Error Interrupt machinery

   - Overhaul of the GIC-V3 ITS driver

   - Small updates and fixes all over the place"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
  genirq: Fix race on spurious interrupt detection
  softirq: Fix typo in __do_softirq() comments
  genirq: Fix grammar s/an /a /
  irqchip/gic: Unify GIC priority definitions
  irqchip/gic-v3: Remove acknowledge loop
  dt-bindings/interrupt-controller: Add documentation for Marvell SEI controller
  dt-bindings/interrupt-controller: Update Marvell ICU bindings
  irqchip/irq-mvebu-icu: Add support for System Error Interrupts (SEI)
  arm64: marvell: Enable SEI driver
  irqchip/irq-mvebu-sei: Add new driver for Marvell SEI
  irqchip/irq-mvebu-icu: Support ICU subnodes
  irqchip/irq-mvebu-icu: Disociate ICU and NSR
  irqchip/irq-mvebu-icu: Clarify the reset operation of configured interrupts
  irqchip/irq-mvebu-icu: Fix wrong private data retrieval
  dt-bindings/interrupt-controller: Fix Marvell ICU length in the example
  genirq/msi: Allow creation of a tree-based irqdomain for platform-msi
  dt-bindings: irqchip: renesas-irqc: Document r8a7744 support
  dt-bindings: irqchip: renesas-irqc: Document R-Car E3 support
  irqchip/pdc: Setup all edge interrupts as rising edge at GIC
  irqchip/gic-v3-its: Allow use of LPI tables in reserved memory
  ...

3 files changed, 113 insertions, 13 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
index aa8bf2ec8905..1c94a57a661e 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
@@ -5,6 +5,8 @@ The Marvell ICU (Interrupt Consolidation Unit) controller is
 responsible for collecting all wired-interrupt sources in the CP and
 communicating them to the GIC in the AP, the unit translates interrupt
 requests on input wires to MSG memory mapped transactions to the GIC.
+These messages will access a different GIC memory area depending on
+their type (NSR, SR, SEI, REI, etc).
 
 Required properties:
 
@@ -12,20 +14,23 @@ Required properties:
 
 - reg: Should contain ICU registers location and length.
 
-- #interrupt-cells: Specifies the number of cells needed to encode an
-  interrupt source. The value shall be 3.
+Subnodes: Each group of interrupt is declared as a subnode of the ICU,
+with their own compatible.
+
+Required properties for the icu_nsr/icu_sei subnodes:
 
-  The 1st cell is the group type of the ICU interrupt. Possible group
-  types are:
+- compatible: Should be one of:
+              * "marvell,cp110-icu-nsr"
+	      * "marvell,cp110-icu-sr"
+	      * "marvell,cp110-icu-sei"
+	      * "marvell,cp110-icu-rei"
 
-   ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure
-   ICU_GRP_SR  (0x1) : Shared peripheral interrupt, secure
-   ICU_GRP_SEI (0x4) : System error interrupt
-   ICU_GRP_REI (0x5) : RAM error interrupt
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2.
 
-  The 2nd cell is the index of the interrupt in the ICU unit.
+  The 1st cell is the index of the interrupt in the ICU unit.
 
-  The 3rd cell is the type of the interrupt. See arm,gic.txt for
+  The 2nd cell is the type of the interrupt. See arm,gic.txt for
   details.
 
 - interrupt-controller: Identifies the node as an interrupt
@@ -35,17 +40,73 @@ Required properties:
   that allows to trigger interrupts using MSG memory mapped
   transactions.
 
+Note: each 'interrupts' property referring to any 'icu_xxx' node shall
+      have a different number within [0:206].
+
 Example:
 
 icu: interrupt-controller@1e0000 {
 	compatible = "marvell,cp110-icu";
-	reg = <0x1e0000 0x10>;
+	reg = <0x1e0000 0x440>;
+
+	CP110_LABEL(icu_nsr): interrupt-controller@10 {
+		compatible = "marvell,cp110-icu-nsr";
+		reg = <0x10 0x20>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		msi-parent = <&gicp>;
+	};
+
+	CP110_LABEL(icu_sei): interrupt-controller@50 {
+		compatible = "marvell,cp110-icu-sei";
+		reg = <0x50 0x10>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		msi-parent = <&sei>;
+	};
+};
+
+node1 {
+	interrupt-parent = <&icu_nsr>;
+	interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+node2 {
+	interrupt-parent = <&icu_sei>;
+	interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+/* Would not work with the above nodes */
+node3 {
+	interrupt-parent = <&icu_nsr>;
+	interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+The legacy bindings were different in this way:
+
+- #interrupt-cells: The value was 3.
+	The 1st cell was the group type of the ICU interrupt. Possible
+	group types were:
+	ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure
+	ICU_GRP_SR  (0x1) : Shared peripheral interrupt, secure
+	ICU_GRP_SEI (0x4) : System error interrupt
+	ICU_GRP_REI (0x5) : RAM error interrupt
+	The 2nd cell was the index of the interrupt in the ICU unit.
+	The 3rd cell was the type of the interrupt. See arm,gic.txt for
+	details.
+
+Example:
+
+icu: interrupt-controller@1e0000 {
+	compatible = "marvell,cp110-icu";
+	reg = <0x1e0000 0x440>;
+
 	#interrupt-cells = <3>;
 	interrupt-controller;
 	msi-parent = <&gicp>;
 };
 
-usb3h0: usb3@500000 {
+node1 {
 	interrupt-parent = <&icu>;
 	interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>;
 };
diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt
new file mode 100644
index 000000000000..0beafed502f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt
@@ -0,0 +1,36 @@
+Marvell SEI (System Error Interrupt) Controller
+-----------------------------------------------
+
+Marvell SEI (System Error Interrupt) controller is an interrupt
+aggregator. It receives interrupts from several sources and aggregates
+them to a single interrupt line (an SPI) on the parent interrupt
+controller.
+
+This interrupt controller can handle up to 64 SEIs, a set comes from the
+AP and is wired while a second set comes from the CPs by the mean of
+MSIs.
+
+Required properties:
+
+- compatible: should be one of:
+              * "marvell,ap806-sei"
+- reg: SEI registers location and length.
+- interrupts: identifies the parent IRQ that will be triggered.
+- #interrupt-cells: number of cells to define an SEI wired interrupt
+                    coming from the AP, should be 1. The cell is the IRQ
+                    number.
+- interrupt-controller: identifies the node as an interrupt controller
+                        for AP interrupts.
+- msi-controller: identifies the node as an MSI controller for the CPs
+                  interrupts.
+
+Example:
+
+        sei: interrupt-controller@3f0200 {
+                compatible = "marvell,ap806-sei";
+                reg = <0x3f0200 0x40>;
+                interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+                #interrupt-cells = <1>;
+                interrupt-controller;
+                msi-controller;
+        };
diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
index a046ed374d80..8de96a4fb2d5 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
@@ -2,10 +2,12 @@ DT bindings for the R-Mobile/R-Car/RZ/G interrupt controller
 
 Required properties:
 
-- compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback.
+- compatible: must be "renesas,irqc-<soctype>" or "renesas,intc-ex-<soctype>",
+	      and "renesas,irqc" as fallback.
   Examples with soctypes are:
     - "renesas,irqc-r8a73a4" (R-Mobile APE6)
     - "renesas,irqc-r8a7743" (RZ/G1M)
+    - "renesas,irqc-r8a7744" (RZ/G1N)
     - "renesas,irqc-r8a7745" (RZ/G1E)
     - "renesas,irqc-r8a77470" (RZ/G1C)
     - "renesas,irqc-r8a7790" (R-Car H2)
@@ -19,6 +21,7 @@ Required properties:
     - "renesas,intc-ex-r8a77965" (R-Car M3-N)
     - "renesas,intc-ex-r8a77970" (R-Car V3M)
     - "renesas,intc-ex-r8a77980" (R-Car V3H)
+    - "renesas,intc-ex-r8a77990" (R-Car E3)
     - "renesas,intc-ex-r8a77995" (R-Car D3)
 - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
   interrupts.txt in this directory