Merge branch 'next' (accumulated 3.16 merge window patches) into master

Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.

* accumulated work in next: (6809 commits)
  ufs: sb mutex merge + mutex_destroy
  powerpc: update comments for generic idle conversion
  cris: update comments for generic idle conversion
  idle: remove cpu_idle() forward declarations
  nbd: zero from and len fields in NBD_CMD_DISCONNECT.
  mm: convert some level-less printks to pr_*
  MAINTAINERS: adi-buildroot-devel is moderated
  MAINTAINERS: add linux-api for review of API/ABI changes
  mm/kmemleak-test.c: use pr_fmt for logging
  fs/dlm/debug_fs.c: replace seq_printf by seq_puts
  fs/dlm/lockspace.c: convert simple_str to kstr
  fs/dlm/config.c: convert simple_str to kstr
  mm: mark remap_file_pages() syscall as deprecated
  mm: memcontrol: remove unnecessary memcg argument from soft limit functions
  mm: memcontrol: clean up memcg zoneinfo lookup
  mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
  mm/mempool.c: update the kmemleak stack trace for mempool allocations
  lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
  mm: introduce kmemleak_update_trace()
  mm/kmemleak.c: use %u to print ->checksum
  ...

1 files changed, 131 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt
new file mode 100644
index 000000000000..b7e71bf5caf4
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,sta350.txt
@@ -0,0 +1,131 @@
+STA350 audio CODEC
+
+The driver for this device only supports I2C.
+
+Required properties:
+
+  - compatible: "st,sta350"
+  - reg: the I2C address of the device for I2C
+  - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+  - power-down-gpios: a GPIO spec for the power down pin. If specified,
+		      it will be deasserted before communication to the codec
+		      starts.
+
+  - vdd-dig-supply: regulator spec, providing 3.3V
+  - vdd-pll-supply: regulator spec, providing 3.3V
+  - vcc-supply: regulator spec, providing 5V - 26V
+
+Optional properties:
+
+  -  st,output-conf: number, Selects the output configuration:
+	0: 2-channel (full-bridge) power, 2-channel data-out
+	1: 2 (half-bridge). 1 (full-bridge) on-board power
+	2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
+	3: 1 Channel Mono-Parallel
+	If parameter is missing, mode 0 will be enabled.
+	This property has to be specified as '/bits/ 8' value.
+
+  -  st,ch1-output-mapping: Channel 1 output mapping
+  -  st,ch2-output-mapping: Channel 2 output mapping
+  -  st,ch3-output-mapping: Channel 3 output mapping
+	0: Channel 1
+	1: Channel 2
+	2: Channel 3
+	If parameter is missing, channel 1 is choosen.
+	This properties have to be specified as '/bits/ 8' values.
+
+  -  st,thermal-warning-recover:
+	If present, thermal warning recovery is enabled.
+
+  -  st,thermal-warning-adjustment:
+	If present, thermal warning adjustment is enabled.
+
+  -  st,fault-detect-recovery:
+	If present, then fault recovery will be enabled.
+
+  -  st,ffx-power-output-mode: string
+	The FFX power output mode selects how the FFX output timing is
+	configured. Must be one of these values:
+	  -  "drop-compensation"
+	  -  "tapered-compensation"
+	  -  "full-power-mode"
+	  -  "variable-drop-compensation" (default)
+
+  -  st,drop-compensation-ns: number
+	Only required for "st,ffx-power-output-mode" ==
+	"variable-drop-compensation".
+	Specifies the drop compensation in nanoseconds.
+	The value must be in the range of 0..300, and only
+	multiples of 20 are allowed. Default is 140ns.
+
+  -  st,overcurrent-warning-adjustment:
+	If present, overcurrent warning adjustment is enabled.
+
+  -  st,max-power-use-mpcc:
+	If present, then MPCC bits are used for MPC coefficients,
+	otherwise standard MPC coefficients are used.
+
+  -  st,max-power-corr:
+	If present, power bridge correction for THD reduction near maximum
+	power output is enabled.
+
+  -  st,am-reduction-mode:
+	If present, FFX mode runs in AM reduction mode, otherwise normal
+	FFX mode is used.
+
+  -  st,odd-pwm-speed-mode:
+	If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
+	channels. If not present, normal PWM spped mode (384 kHz) will be used.
+
+  -  st,distortion-compensation:
+	If present, distortion compensation variable uses DCC coefficient.
+	If not present, preset DC coefficient is used.
+
+  -  st,invalid-input-detect-mute:
+	If present, automatic invalid input detect mute is enabled.
+
+  -  st,activate-mute-output:
+	If present, a mute output will be activated in ase the volume will
+	reach a value lower than -76 dBFS.
+
+  -  st,bridge-immediate-off:
+	If present, the bridge will be switched off immediately after the
+	power-down-gpio goes low. Otherwise, the bridge will wait for 13
+	million clock cycles to pass before shutting down.
+
+  -  st,noise-shape-dc-cut:
+	If present, the noise-shaping technique on the DC cutoff filter are
+	enabled.
+
+  -  st,powerdown-master-volume:
+	If present, the power-down pin and I2C power-down functions will
+	act on the master volume. Otherwise, the functions will act on the
+	mute commands.
+
+  -  st,powerdown-delay-divider:
+	If present, the bridge power-down time will be divided by the provided
+	value. If not specified, a divider of 1 will be used. Allowed values
+	are 1, 2, 4, 8, 16, 32, 64 and 128.
+	This property has to be specified as '/bits/ 8' value.
+
+Example:
+
+codec: sta350@38 {
+	compatible = "st,sta350";
+	reg = <0x1c>;
+	reset-gpios = <&gpio1 19 0>;
+	power-down-gpios = <&gpio1 16 0>;
+	st,output-conf = /bits/ 8  <0x3>;	// set output to 2-channel
+						// (full-bridge) power,
+						// 2-channel data-out
+	st,ch1-output-mapping = /bits/ 8 <0>;	// set channel 1 output ch 1
+	st,ch2-output-mapping = /bits/ 8 <0>;	// set channel 2 output ch 1
+	st,ch3-output-mapping = /bits/ 8 <0>;	// set channel 3 output ch 1
+	st,max-power-correction;		// enables power bridge
+						// correction for THD reduction
+						// near maximum power output
+	st,invalid-input-detect-mute;		// mute if no valid digital
+						// audio signal is provided.
+};