Merge tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "No dramatic changes are found in this development cycle, but as usual,
  many commits are applied in a wide range of drivers.

  Most of big changes are in ASoC, where a few bits of framework work
  and quite a lot of cleanups and improvements to existing code have
  been done. The rest are usual stuff, a few HD-audio and USB-audio
  quirks and fixes, as well as the drop of kthread usages in the whole
  subsystem.

  Below are some highlights:

  ASoC:
   - support for stereo DAPM controls
   - some initial work on the of-graph sound card
   - regmap conversions of the remaining AC'97 drivers
   - a new version of the topology ABI; this should be backward
     compatible
   - updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
     Intel skylake, atom-sst
   - new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
     Realtek RT5665

  USB-audio:
   - yet another race fix at disconnection
   - tolerated packet size calculation for some Android devices
   - quirks for Axe-Fx II, QuickCam, TEAC 501/503

  HD-audio:
   - improvement of Dell pin fixup mapping
   - quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic

  Misc:
   - replace all kthread usages with simple works"

* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
  ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
  ALSA: usb-audio: Eliminate noise at the start of DSD playback.
  ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
  ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
  ASoC: topology: avoid uninitialized kcontrol_type
  ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
  ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
  ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
  ASoC: zte: spdif and i2s drivers are not zx296702 specific
  ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
  ASoC: rsnd: enable/disable ADG when suspend/resume timing
  ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
  ALSA: cs46xx: add a new line
  ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
  ASoC: nau8825: disable sinc filter for high THD of ADC
  ALSA: usb-audio: more tolerant packetsize
  ALSA: usb-audio: avoid setting of sample rate multiple times on bus
  ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
  ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
  ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
  ...

1 files changed, 88 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
new file mode 100644
index 000000000000..5b9b38f578bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
@@ -0,0 +1,88 @@
+Devicetree bindings for the Axentia TSE-850 audio complex
+
+Required properties:
+  - compatible: "axentia,tse850-pcm5142"
+  - axentia,ssc-controller: The phandle of the atmel SSC controller used as
+    cpu dai.
+  - axentia,audio-codec: The phandle of the PCM5142 codec.
+  - axentia,add-gpios: gpio specifier that controls the mixer.
+  - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1.
+  - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2.
+  - axentia,ana-supply: Regulator that supplies the output amplifier. Must
+    support voltages in the 2V - 20V range, in 1V steps.
+
+The schematics explaining the gpios are as follows:
+
+               loop1 relays
+   IN1 +---o  +------------+  o---+ OUT1
+            \                /
+             +              +
+             |   /          |
+             +--o  +--.     |
+             |  add   |     |
+             |        V     |
+             |      .---.   |
+   DAC +----------->|Sum|---+
+             |      '---'   |
+             |              |
+             +              +
+
+   IN2 +---o--+------------+--o---+ OUT2
+               loop2 relays
+
+The 'loop1' gpio pin controlls two relays, which are either in loop position,
+meaning that input and output are directly connected, or they are in mixer
+position, meaning that the signal is passed through the 'Sum' mixer. Similarly
+for 'loop2'.
+
+In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer
+(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays
+are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2
+are TSE-850 connectors and DAC is the PCB name of the (filtered) output from
+the PCM5142 codec.
+
+Example:
+
+	&i2c {
+		codec: pcm5142@4c {
+			compatible = "ti,pcm5142";
+
+			reg = <0x4c>;
+
+			AVDD-supply = <&reg_3v3>;
+			DVDD-supply = <&reg_3v3>;
+			CPVDD-supply = <&reg_3v3>;
+
+			clocks = <&sck>;
+
+			pll-in = <3>;
+			pll-out = <6>;
+		};
+	};
+
+	ana: ana-reg {
+		compatible = "pwm-regulator";
+
+		regulator-name = "ANA";
+
+		pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+		pwm-dutycycle-unit = <1000>;
+		pwm-dutycycle-range = <100 1000>;
+
+		regulator-min-microvolt = <2000000>;
+		regulator-max-microvolt = <20000000>;
+		regulator-ramp-delay = <1000>;
+	};
+
+	sound {
+		compatible = "axentia,tse850-pcm5142";
+
+		axentia,ssc-controller = <&ssc0>;
+		axentia,audio-codec = <&codec>;
+
+		axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+		axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+		axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+		axentia,ana-supply = <&ana>;
+	};