Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late DT updates from Arnd Bergmann:
 "These updates have been kept in a separate branch mostly because they
  rely on updates to the respective clk drivers to keep the shared
  header files in sync.

   - The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
     automotive SoC similar to the ⅹ8a7795 chip we already support, but
     the dts changes rely on a clock driver change that has been merged
     for v4.9 through the clk tree.

   - The Amlogic meson-gxbb (S905) platform gains support for a few
     drivers merged through our tree, in particular the network and usb
     driver changes are required and included here, and also the clk
     tree changes.

   - The Allwinner platforms have seen a large-scale change to their clk
     drivers and the dts file updates must come after that. This
     includes the newly added Nextthing GR8 platform, which is derived
     from sun5i/A13.

   - Some integrator (arm32) changes rely on clk driver changes.

   - A single patch for lpc32xx has no such dependency but wasn't added
     until just before the merge window"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  ARM: dts: lpc32xx: add device node for IRAM on-chip memory
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ...

1 files changed, 27 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt
new file mode 100644
index 000000000000..9da5ea234154
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/meson-usb2-phy.txt
@@ -0,0 +1,27 @@
+* Amlogic USB2 PHY
+
+Required properties:
+- compatible:	Depending on the platform this should be one of:
+	"amlogic,meson8b-usb2-phy"
+	"amlogic,meson-gxbb-usb2-phy"
+- reg:		The base address and length of the registers
+- #phys-cells:	should be 0 (see phy-bindings.txt in this directory)
+- clocks:	phandle and clock identifier for the phy clocks
+- clock-names:	"usb_general" and "usb"
+
+Optional properties:
+- resets:	reference to the reset controller
+- phy-supply:	see phy-bindings.txt in this directory
+
+
+Example:
+
+usb0_phy: usb_phy@0 {
+	compatible = "amlogic,meson-gxbb-usb2-phy";
+	#phy-cells = <0>;
+	reg = <0x0 0x0 0x0 0x20>;
+	resets = <&reset RESET_USB_OTG>;
+	clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
+	clock-names = "usb_general", "usb";
+	phy-supply = <&usb_vbus>;
+};