Merge branch 'pci/host-designware' into next

* pci/host-designware:
  ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
  MAINTAINERS: Add PCI Endpoint maintainer
  Documentation: PCI: Add userguide for PCI endpoint test function
  tools: PCI: Add sample test script to invoke pcitest
  tools: PCI: Add a userspace tool to test PCI endpoint
  Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
  misc: Add host side PCI driver for PCI test function device
  PCI: Add device IDs for DRA74x and DRA72x
  dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
  PCI: dwc: dra7xx: Workaround for errata id i870
  dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
  PCI: dwc: dra7xx: Add EP mode support
  PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
  dt-bindings: PCI: Add DT bindings for PCI designware EP mode
  PCI: dwc: designware: Add EP mode support
  Documentation: PCI: Add binding documentation for pci-test endpoint function
  PCI: endpoint: functions: Add an EP function to test PCI
  Documentation: PCI: Add specification for the *PCI test* function device
  PCI: endpoint: Create configfs entry for EPC device and EPF driver
  Documentation: PCI: Guide to use PCI endpoint configfs
  PCI: endpoint: Introduce configfs entry for configuring EP functions
  Documentation: PCI: Guide to use PCI Endpoint Core Layer
  PCI: endpoint: Add EP core layer to enable EP controller and EP functions
  PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe
  PCI: dwc: designware: Move _unroll configurations to a separate function
  PCI: dwc: all: Modify dbi accessors to access data of 4/2/1 bytes
  PCI: dwc: all: Modify dbi accessors to take dbi_base as argument
  PCI: dwc: artpec6: Populate cpu_addr_fixup ops
  PCI: dwc: dra7xx: Populate cpu_addr_fixup ops
  PCI: dwc: designware: Add new *ops* for CPU addr fixup
  PCI: dwc: Fix uninitialized variable in dw_handle_msi_irq()
  PCI: dwc: Unindent dw_handle_msi_irq() loop
  PCI: dwc: Fix dw_pcie_ops NULL pointer dereference
  PCI: dwc: Select PCI_HOST_COMMON for hisi
  PCI: thunder-pem: Fix legacy firmware PEM-specific resources
  PCI: thunder-pem: Add legacy firmware support for Cavium ThunderX host controller
  PCI: thunder-pem: Use Cavium assigned hardware ID for ThunderX host controller
  PCI: iproc: Save host bridge window resource in struct iproc_pcie
  PCI/ASPM: Always set link->downstream to avoid NULL dereference on remove
  PCI: Prevent VPD access for QLogic ISP2722
  PCI: exynos: Initialize elbi_base even when using PHY framework

2 files changed, 53 insertions, 15 deletions

diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
index 1392c705ceca..b2480dd38c11 100644
--- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
@@ -6,30 +6,40 @@ Required properties:
 - reg-names: Must be "config" for the PCIe configuration space.
     (The old way of getting the configuration address space from "ranges"
     is deprecated and should be avoided.)
+- num-lanes: number of lanes to use
+RC mode:
 - #address-cells: set to <3>
 - #size-cells: set to <2>
 - device_type: set to "pci"
 - ranges: ranges for the PCI memory and I/O regions
 - #interrupt-cells: set to <1>
-- interrupt-map-mask and interrupt-map: standard PCI properties
-	to define the mapping of the PCIe interface to interrupt
+- interrupt-map-mask and interrupt-map: standard PCI
+	properties to define the mapping of the PCIe interface to interrupt
 	numbers.
-- num-lanes: number of lanes to use
+EP mode:
+- num-ib-windows: number of inbound address translation
+        windows
+- num-ob-windows: number of outbound address translation
+        windows
 
 Optional properties:
-- num-viewport: number of view ports configured in hardware.  If a platform
-  does not specify it, the driver assumes 2.
 - num-lanes: number of lanes to use (this property should be specified unless
   the link is brought already up in BIOS)
 - reset-gpio: gpio pin number of power good signal
-- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
-  specify this property, to keep backwards compatibility a range of 0x00-0xff
-  is assumed if not present)
 - clocks: Must contain an entry for each entry in clock-names.
 	See ../clocks/clock-bindings.txt for details.
 - clock-names: Must include the following entries:
 	- "pcie"
 	- "pcie_bus"
+RC mode:
+- num-viewport: number of view ports configured in
+  hardware. If a platform does not specify it, the driver assumes 2.
+- bus-range: PCI bus numbers covered (it is recommended
+  for new devicetrees to specify this property, to keep backwards
+  compatibility a range of 0x00-0xff is assumed if not present)
+EP mode:
+- max-functions: maximum number of functions that can be
+  configured
 
 Example configuration:
 
diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
index 60e25161f351..6a07c96227e0 100644
--- a/Documentation/devicetree/bindings/pci/ti-pci.txt
+++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
@@ -1,17 +1,22 @@
 TI PCI Controllers
 
 PCIe Designware Controller
- - compatible: Should be "ti,dra7-pcie""
- - reg : Two register ranges as listed in the reg-names property
- - reg-names : The first entry must be "ti-conf" for the TI specific registers
-	       The second entry must be "rc-dbics" for the designware pcie
-	       registers
-	       The third entry must be "config" for the PCIe configuration space
+ - compatible: Should be "ti,dra7-pcie" for RC
+	       Should be "ti,dra7-pcie-ep" for EP
  - phys : list of PHY specifiers (used by generic PHY framework)
  - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
 	       number of PHYs as specified in *phys* property.
  - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
 	       where <X> is the instance number of the pcie from the HW spec.
+ - num-lanes as specified in ../designware-pcie.txt
+
+HOST MODE
+=========
+ - reg : Two register ranges as listed in the reg-names property
+ - reg-names : The first entry must be "ti-conf" for the TI specific registers
+	       The second entry must be "rc-dbics" for the DesignWare PCIe
+	       registers
+	       The third entry must be "config" for the PCIe configuration space
  - interrupts : Two interrupt entries must be specified. The first one is for
 		main interrupt line and the second for MSI interrupt line.
  - #address-cells,
@@ -19,13 +24,36 @@ PCIe Designware Controller
    #interrupt-cells,
    device_type,
    ranges,
-   num-lanes,
    interrupt-map-mask,
    interrupt-map : as specified in ../designware-pcie.txt
 
+DEVICE MODE
+===========
+ - reg : Four register ranges as listed in the reg-names property
+ - reg-names : "ti-conf" for the TI specific registers
+	       "ep_dbics" for the standard configuration registers as
+		they are locally accessed within the DIF CS space
+	       "ep_dbics2" for the standard configuration registers as
+		they are locally accessed within the DIF CS2 space
+	       "addr_space" used to map remote RC address space
+ - interrupts : one interrupt entries must be specified for main interrupt.
+ - num-ib-windows : number of inbound address translation windows
+ - num-ob-windows : number of outbound address translation windows
+ - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
+			       should contain the register offset within syscon
+			       and the 2nd argument should contain the bit field
+			       for setting the bit to enable unaligned
+			       access.
+
 Optional Property:
  - gpios : Should be added if a gpio line is required to drive PERST# line
 
+NOTE: Two DT nodes may be added for each PCI controller; one for host
+mode and another for device mode. So in order for PCI to
+work in host mode, EP mode DT node should be disabled and in order to PCI to
+work in EP mode, host mode DT node should be disabled. Host mode and EP
+mode are mutually exclusive.
+
 Example:
 axi {
 	compatible = "simple-bus";