Merge branch 'master' into for-next

2 files changed, 106 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt
new file mode 100644
index 000000000000..2fa4fcd38fd6
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt
@@ -0,0 +1,53 @@
+CAN Device Tree Bindings
+------------------------
+
+(c) 2006-2009 Secret Lab Technologies Ltd
+Grant Likely <grant.likely@secretlab.ca>
+
+fsl,mpc5200-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source shall be used for the controller:
+
+- fsl,mscan-clock-source : a string describing the clock source. Valid values
+			   are:	"ip" for ip bus clock
+				 "ref" for reference clock (XTAL)
+			   "ref" is default in case this property is not
+			   present.
+
+fsl,mpc5121-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source and divider shall be used for the controller:
+
+- fsl,mscan-clock-source : a string describing the clock source. Valid values
+			   are:	"ip" for ip bus clock
+				"ref" for reference clock
+				"sys" for system clock
+			   If this property is not present, an optimal CAN
+			   clock source and frequency based on the system
+			   clock will be selected. If this is not possible,
+			   the reference clock will be used.
+
+- fsl,mscan-clock-divider: for the reference and system clock, an additional
+			   clock divider can be specified. By default, a
+			   value of 1 is used.
+
+Note that the MPC5121 Rev. 1 processor is not supported.
+
+Examples:
+	can@1300 {
+		compatible = "fsl,mpc5121-mscan";
+		interrupts = <12 0x8>;
+		interrupt-parent = <&ipic>;
+		reg = <0x1300 0x80>;
+	};
+
+	can@1380 {
+		compatible = "fsl,mpc5121-mscan";
+		interrupts = <13 0x8>;
+		interrupt-parent = <&ipic>;
+		reg = <0x1380 0x80>;
+		fsl,mscan-clock-source = "ref";
+		fsl,mscan-clock-divider = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt
new file mode 100644
index 000000000000..d6d209ded937
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/sja1000.txt
@@ -0,0 +1,53 @@
+Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
+
+Required properties:
+
+- compatible : should be "nxp,sja1000".
+
+- reg : should specify the chip select, address offset and size required
+	to map the registers of the SJA1000. The size is usually 0x80.
+
+- interrupts: property with a value describing the interrupt source
+	(number and sensitivity) required for the SJA1000.
+
+Optional properties:
+
+- nxp,external-clock-frequency : Frequency of the external oscillator
+	clock in Hz. Note that the internal clock frequency used by the
+	SJA1000 is half of that value. If not specified, a default value
+	of 16000000 (16 MHz) is used.
+
+- nxp,tx-output-mode : operation mode of the TX output control logic:
+	<0x0> : bi-phase output mode
+	<0x1> : normal output mode (default)
+	<0x2> : test output mode
+	<0x3> : clock output mode
+
+- nxp,tx-output-config : TX output pin configuration:
+	<0x01> : TX0 invert
+	<0x02> : TX0 pull-down (default)
+	<0x04> : TX0 pull-up
+	<0x06> : TX0 push-pull
+	<0x08> : TX1 invert
+	<0x10> : TX1 pull-down
+	<0x20> : TX1 pull-up
+	<0x30> : TX1 push-pull
+
+- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
+	If not specified or if the specified value is 0, the CLKOUT pin
+	will be disabled.
+
+- nxp,no-comparator-bypass : Allows to disable the CAN input comperator.
+
+For futher information, please have a look to the SJA1000 data sheet.
+
+Examples:
+
+can@3,100 {
+	compatible = "nxp,sja1000";
+	reg = <3 0x100 0x80>;
+	interrupts = <2 0>;
+	interrupt-parent = <&mpic>;
+	nxp,external-clock-frequency = <16000000>;
+};
+