Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd

Pull MTD updates from David Woodhouse:
 - Various cleanups especially in NAND tests
 - Add support for NAND flash on BCMA bus
 - DT support for sh_flctl and denali NAND drivers
 - Kill obsolete/superceded drivers (fortunet, nomadik_nand)
 - Fix JFFS2 locking bug in ENOMEM failure path
 - New SPI flash chips, as usual
 - Support writing in 'reliable mode' for DiskOnChip G4
 - Debugfs support in nandsim

* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
  mtd: nand: typo in nand_id_has_period() comments
  mtd: nand/gpio: use io{read,write}*_rep accessors
  mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
  mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
  mtd: nand/docg4: fix and improve read of factory bbt
  mtd: nand/docg4: reserve bb marker area in ecclayout
  mtd: nand/docg4: add support for writing in reliable mode
  mtd: mxc_nand: reorder part_probes to let cmdline override other sources
  mtd: mxc_nand: fix unbalanced clk_disable() in error path
  mtd: nandsim: Introduce debugfs infrastructure
  mtd: physmap_of: error checking to prevent a NULL pointer dereference
  mtg: docg3: potential divide by zero in doc_write_oob()
  mtd: bcm47xxnflash: writing support
  mtd: tests/read: initialize buffer for whole next page
  mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
  mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
  mtd: nand: onfi need to be probed in 8 bits mode
  mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
  mtd: nand: print flash size during detection
  mted: nand_wait_ready timeout fix
  ...

1 files changed, 29 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt
new file mode 100644
index 000000000000..6d3d57609470
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/m25p80.txt
@@ -0,0 +1,29 @@
+* MTD SPI driver for ST M25Pxx (and similar) serial flash chips
+
+Required properties:
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- compatible : Should be the manufacturer and the name of the chip. Bear in mind
+               the DT binding is not Linux-only, but in case of Linux, see the
+               "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of
+               supported chips.
+- reg : Chip-Select number
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
+
+Optional properties:
+- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead
+                   of the usual "read" opcode. This opcode is not supported by
+                   all chips and support for it can not be detected at runtime.
+                   Refer to your chips' datasheet to check if this is supported
+                   by your chip.
+
+Example:
+
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,m25p80";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		m25p,fast-read;
+	};