Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for Linux 4.1.  Most
  noteworthy:

   - Add more Octeon-optimized crypto functions
   - Octeon crypto preemption and locking fixes
   - Little endian support for Octeon
   - Use correct CSR to soft reset Octeons
   - Support LEDs on the Octeon-based DSR-1000N
   - Fix PCI interrupt mapping for the Octeon-based DSR-1000N
   - Mark prom_free_prom_memory() as __init for a number of systems
   - Support for Imagination's Pistachio SOC.  This includes arch and
     CLK bits.  I'd like to merge pinctrl bits later
   - Improve parallelism of csum_partial for certain pipelines
   - Organize DTB files in subdirs like other architectures
   - Implement read_sched_clock for all MIPS platforms other than
     Octeon
   - Massive series of 38 fixes and cleanups for the FPU emulator /
     kernel
   - Further FPU remulator work to support new features.  This sits on a
     separate branch which also has been pulled into the 4.1 KVM branch
   - Clean up and fixes for the SEAD3 eval board; remove unused file
   - Various updates for Netlogic platforms
   - A number of small updates for Loongson 3 platforms
   - Increase the memory limit for ATH79 platforms to 256MB
   - A fair number of fixes and updates for BCM47xx platforms
   - Finish the implementation of XPA support
   - MIPS FDC support.  No, not floppy controller but Fast Debug Channel :)
   - Detect the R16000 used in SGI legacy platforms
   - Fix Kconfig dependencies for the SSB bus support"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
  MIPS: Makefile: Fix MIPS ASE detection code
  MIPS: asm: elf: Set O32 default FPU flags
  MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
  MIPS: Kconfig: Disable SMP/CPS for 64-bit
  MIPS: Hibernate: flush TLB entries earlier
  MIPS: smp-cps: cpu_set FPU mask if FPU present
  MIPS: lose_fpu(): Disable FPU when MSA enabled
  MIPS: ralink: add missing symbol for RALINK_ILL_ACC
  MIPS: ralink: Fix bad config symbol in PCI makefile.
  SSB: fix Kconfig dependencies
  MIPS: Malta: Detect and fix bad memsize values
  Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
  MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
  MIPS: Fix cpu_has_mips_r2_exec_hazard.
  MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
  MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
  MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
  MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
  MIPS: unaligned: Fix regular load/store instruction emulation for EVA
  MIPS: unaligned: Surround load/store macros in do {} while statements
  ...

1 files changed, 3 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
index bae1f2187226..44a9bb15dd56 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
@@ -13,8 +13,7 @@ Such an interrupt controller has the following hardware design:
   or if they will output an interrupt signal at this 2nd level interrupt
   controller, in particular for UARTs
 
-- typically has one 32-bit enable word and one 32-bit status word, but on
-  some hardware may have more than one enable/status pair
+- has one 32-bit enable word and one 32-bit status word
 
 - no atomic set/clear operations
 
@@ -53,9 +52,7 @@ The typical hardware layout for this controller is represented below:
 Required properties:
 
 - compatible: should be "brcm,bcm7120-l2-intc"
-- reg: specifies the base physical address and size of the registers;
-  multiple pairs may be specified, with the first pair handling IRQ offsets
-  0..31 and the second pair handling 32..63
+- reg: specifies the base physical address and size of the registers
 - interrupt-controller: identifies the node as an interrupt controller
 - #interrupt-cells: specifies the number of cells needed to encode an interrupt
   source, should be 1.
@@ -66,10 +63,7 @@ Required properties:
 - brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts
   are wired to this 2nd level interrupt controller, and how they match their
   respective interrupt parents. Should match exactly the number of interrupts
-  specified in the 'interrupts' property, multiplied by the number of
-  enable/status register pairs implemented by this controller.  For
-  multiple parent IRQs with multiple enable/status words, this looks like:
-  <irq0_w0 irq0_w1 irq1_w0 irq1_w1 ...>
+  specified in the 'interrupts' property.
 
 Optional properties: