Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux

Pull devicetree changes from Grant Likely:
 "Here are the devicetree changes queued up for v4.1.  Nothing really
  exciting here.  Rob has another few commits for big-endian attached
  UARTs, but those will be sent in a separate merge request since they
  haven't been as thoroughly tested as this batch.

  Here are the highlights:

   - lots of unittest cleanup from Frank Rowand

   - bugfixes and updates to the of_graph code

   - tighten up of_get_mac_address() code

   - documentation updates"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
  of/unittest: Fix of_platform_depopulate test case
  of/unittest: early return from test skips tests
  of/unittest: breadcrumbs to reduce pain of future maintainers
  of/unittest: reduce checkpatch noise - line after declarations
  of/unittest: typo in error string
  of/unittest: add const where needed
  of_net: factor out repetitive code from of_get_mac_address()
  drivers/of: Add empty ranges quirk for PA-Semi
  of: Allow selection of OF_DYNAMIC and OF_OVERLAY if OF_UNITTEST
  of: Empty node & property flag accessors when !OF
  of: Explicitly include linux/types.h in of_graph.h
  dt-bindings: brcm: rationalize Broadcom documentation naming
  of/unittest: replace 'selftest' with 'unittest'
  Documentation: rename of_selftest.txt to of_unittest.txt
  Documentation: update the of_selftest.txt
  dt: OF_UNITTEST make dependency broken
  MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
  of: Add of_graph_get_port_by_id function
  of: Add for_each_endpoint_of_node helper macro
  of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint

1 files changed, 52 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
new file mode 100644
index 000000000000..4a63bc96b687
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
@@ -0,0 +1,52 @@
+Broadcom Kona Family GPIO
+=========================
+
+This GPIO driver is used in the following Broadcom SoCs:
+  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+The Broadcom GPIO Controller IP can be configured prior to synthesis to
+support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+GPIO controller only supports edge, not level, triggering of interrupts.
+
+Required properties
+-------------------
+
+- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt outputs from the controller. There is one GPIO
+  interrupt per GPIO bank. The number of interrupts listed depends on the
+  number of GPIO banks on the SoC. The interrupts must be ordered by bank,
+  starting with bank 0. There is always a 1:1 mapping between banks and
+  IRQs.
+- #gpio-cells: Should be <2>. The first cell is the pin number, the second
+  cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+  See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
+- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
+  second cell is used to specify flags. The following subset of flags is
+  supported:
+  - trigger type (bits[1:0]):
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      3 = low-to-high or high-to-low edge triggered
+      Valid values are 1, 2, 3
+  See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
+- gpio-controller: Marks the device node as a GPIO controller.
+- interrupt-controller: Marks the device node as an interrupt controller.
+
+Example:
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x800>;
+		interrupts =
+		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};