V4L/DVB: em28xx: add Dikom DK300 hybrid USB tuner

Adds digital and analogue tv support for Dikom DK300 hybrid usb card.

Not working: remote controller

To be done: it seems that with the proposed patch the digital demodulator
remains activated if the tuner is switched from digital to analogue mode.

Workaround is to unplug and replug the device when switching from digital to
analogue. If someone can explain how to verify the gpio settings using the
usbsnoop, the above issue perhaps can be resolved.

Signed-off-by: Andrea Amorosi <Andrea.Amorosi76@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

3 files changed, 50 insertions, 0 deletions

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 62ca31d44b56..48d7f7e284ad 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -232,6 +232,12 @@ static struct em28xx_reg_seq vc211a_enable[] = {
 	{	-1,		-1,	-1,		-1},
 };
 
+static struct em28xx_reg_seq dikom_dk300_digital[] = {
+	{EM28XX_R08_GPIO,	0x6e,	~EM_GPIO_4,	10},
+	{EM2880_R04_GPO,	0x08,	0xff,		10},
+	{ -1,			-1,	-1,		-1},
+};
+
 
 /*
  *  Board definitions
@@ -1440,6 +1446,21 @@ struct em28xx_board em28xx_boards[] = {
 			.gpio     = hauppauge_wintv_hvr_900_analog,
 		} },
 	},
+	[EM2882_BOARD_DIKOM_DK300] = {
+		.name         = "Dikom DK300",
+		.tuner_type   = TUNER_XC2028,
+		.tuner_gpio   = default_tuner_gpio,
+		.decoder      = EM28XX_TVP5150,
+		.mts_firmware = 1,
+		.has_dvb      = 1,
+		.dvb_gpio     = dikom_dk300_digital,
+		.input        = { {
+			.type     = EM28XX_VMUX_TELEVISION,
+			.vmux     = TVP5150_COMPOSITE0,
+			.amux     = EM28XX_AMUX_VIDEO,
+			.gpio     = default_analog,
+		} },
+	},
 	[EM2883_BOARD_KWORLD_HYBRID_330U] = {
 		.name         = "Kworld PlusTV HD Hybrid 330",
 		.tuner_type   = TUNER_XC2028,
@@ -1760,6 +1781,7 @@ static struct em28xx_hash_table em28xx_eeprom_hash[] = {
 	{0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028},
 	{0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028},
 	{0x63f653bd, EM2870_BOARD_REDDO_DVB_C_USB_BOX, TUNER_ABSENT},
+	{0x4e913442, EM2882_BOARD_DIKOM_DK300, TUNER_XC2028},
 };
 
 /* I2C devicelist hash table for devices with generic USB IDs */
@@ -2112,6 +2134,7 @@ static void em28xx_setup_xc3028(struct em28xx *dev, struct xc2028_ctrl *ctl)
 		ctl->demod = XC3028_FE_DEFAULT;
 		break;
 	case EM2883_BOARD_KWORLD_HYBRID_330U:
+	case EM2882_BOARD_DIKOM_DK300:
 		ctl->demod = XC3028_FE_CHINA;
 		ctl->fname = XC2028_DEFAULT_FIRMWARE;
 		break;
@@ -2397,6 +2420,31 @@ void em28xx_card_setup(struct em28xx *dev)
 		em28xx_gpio_set(dev, dev->board.tuner_gpio);
 		em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
 		break;
+
+/*
+		 * The Dikom DK300 is detected as an Kworld VS-DVB-T 323UR.
+		 *
+		 * This occurs because they share identical USB vendor and
+		 * product IDs.
+		 *
+		 * What we do here is look up the EEPROM hash of the Dikom
+		 * and if it is found then we decide that we do not have
+		 * a Kworld and reset the device to the Dikom instead.
+		 *
+		 * This solution is only valid if they do not share eeprom
+		 * hash identities which has not been determined as yet.
+		 */
+	case EM2882_BOARD_KWORLD_VS_DVBT:
+		if (!em28xx_hint_board(dev))
+			em28xx_set_model(dev);
+
+		/* In cases where we had to use a board hint, the call to
+		   em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
+		   so make the call now so the analog GPIOs are set properly
+		   before probing the i2c bus. */
+		em28xx_gpio_set(dev, dev->board.tuner_gpio);
+		em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
+		break;
 	}
 
 #if defined(CONFIG_MODULES) && defined(MODULE)
diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c
index 6b0a4953ab0e..fcf8c10eac45 100644
--- a/drivers/media/video/em28xx/em28xx-dvb.c
+++ b/drivers/media/video/em28xx/em28xx-dvb.c
@@ -503,6 +503,7 @@ static int dvb_init(struct em28xx *dev)
 		break;
 	case EM2880_BOARD_TERRATEC_HYBRID_XS:
 	case EM2881_BOARD_PINNACLE_HYBRID_PRO:
+	case EM2882_BOARD_DIKOM_DK300:
 		dvb->frontend = dvb_attach(zl10353_attach,
 					   &em28xx_zl10353_xc3028_no_i2c_gate,
 					   &dev->i2c_adap);
diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h
index 0cb8d151cd0b..ba6fe5daff84 100644
--- a/drivers/media/video/em28xx/em28xx.h
+++ b/drivers/media/video/em28xx/em28xx.h
@@ -111,6 +111,7 @@
 #define EM2861_BOARD_GADMEI_UTV330PLUS           72
 #define EM2870_BOARD_REDDO_DVB_C_USB_BOX          73
 #define EM2800_BOARD_VC211A			  74
+#define EM2882_BOARD_DIKOM_DK300		  75
 
 /* Limits minimum and default number of buffers */
 #define EM28XX_MIN_BUF 4