kernel/linux.git/include/net/seg6.h, branch v6.6.134

udp6: Use Segment Routing Header for dest address if present

2022-01-04T12:17:35+00:00

When finding the socket to report an error on, if the invoking packet is using Segment Routing, the IPv6 destination address is that of an intermediate router, not the end destination. Extract the ultimate destination address from the segment address. This change allows traceroute to function in the presence of Segment Routing. Signed-off-by: Andrew Lunn Reviewed-by: David Ahern Reviewed-by: Willem de Bruijn Signed-off-by: David S. Miller

icmp: ICMPV6: Examine invoking packet for Segment Route Headers.

2022-01-04T12:17:35+00:00

RFC8754 says: ICMP error packets generated within the SR domain are sent to source nodes within the SR domain. The invoking packet in the ICMP error message may contain an SRH. Since the destination address of a packet with an SRH changes as each segment is processed, it may not be the destination used by the socket or application that generated the invoking packet. For the source of an invoking packet to process the ICMP error message, the ultimate destination address of the IPv6 header may be required. The following logic is used to determine the destination address for use by protocol-error handlers. * Walk all extension headers of the invoking IPv6 packet to the routing extension header preceding the upper-layer header. - If routing header is type 4 Segment Routing Header (SRH) o The SID at Segment List[0] may be used as the destination address of the invoking packet. Mangle the skb so the network header points to the invoking packet inside the ICMP packet. The seg6 helpers can then be used on the skb to find any segment routing headers. If found, mark this fact in the IPv6 control block of the skb, and store the offset into the packet of the SRH. Then restore the skb back to its old state. Signed-off-by: Andrew Lunn Reviewed-by: David Ahern Reviewed-by: Willem de Bruijn Signed-off-by: David S. Miller

seg6: export get_srh() for ICMP handling

2022-01-04T12:17:35+00:00

An ICMP error message can contain in its message body part of an IPv6 packet which invoked the error. Such a packet might contain a segment router header. Export get_srh() so the ICMP code can make use of it. Since his changes the scope of the function from local to global, add the seg6_ prefix to keep the namespace clean. And move it into seg6.c so it is always available, not just when IPV6_SEG6_LWTUNNEL is enabled. Signed-off-by: Andrew Lunn Reviewed-by: David Ahern Reviewed-by: Willem de Bruijn Signed-off-by: David S. Miller

seg6: fix seg6_validate_srh() to avoid slab-out-of-bounds

2020-06-04T22:39:32+00:00

The seg6_validate_srh() is used to validate SRH for three cases: case1: SRH of data-plane SRv6 packets to be processed by the Linux kernel. Case2: SRH of the netlink message received from user-space (iproute2) Case3: SRH injected into packets through setsockopt In case1, the SRH can be encoded in the Reduced way (i.e., first SID is carried in DA only and not represented as SID in the SRH) and the seg6_validate_srh() now handles this case correctly. In case2 and case3, the SRH shouldn’t be encoded in the Reduced way otherwise we lose the first segment (i.e., the first hop). The current implementation of the seg6_validate_srh() allow SRH of case2 and case3 to be encoded in the Reduced way. This leads a slab-out-of-bounds problem. This patch verifies SRH of case1, case2 and case3. Allowing case1 to be reduced while preventing SRH of case2 and case3 from being reduced . Reported-by: syzbot+e8c028b62439eac42073@syzkaller.appspotmail.com Reported-by: YueHaibing Fixes: 0cb7498f234e ("seg6: fix SRH processing to comply with RFC8754") Signed-off-by: Ahmed Abdelsalam Signed-off-by: David S. Miller

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

2019-05-30T18:26:32+00:00

Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman

net: seg6.h: remove an unused #include

2018-12-21T00:56:04+00:00

A minor code cleanup. Signed-off-by: Peter Oskolkov Signed-off-by: David S. Miller

rhashtable: split rhashtable.h

2018-06-22T04:43:27+00:00

Due to the use of rhashtables in net namespaces, rhashtable.h is included in lots of the kernel, so a small changes can required a large recompilation. This makes development painful. This patch splits out rhashtable-types.h which just includes the major type declarations, and does not include (non-trivial) inline code. rhashtable.h is no longer included by anything in the include/ directory. Common include files only include rhashtable-types.h so a large recompilation is only triggered when that changes. Acked-by: Herbert Xu Signed-off-by: NeilBrown Signed-off-by: David S. Miller

ipv6: sr: export function lookup_nexthop

2018-05-24T09:57:35+00:00

The function lookup_nexthop is essential to implement most of the seg6local actions. As we want to provide a BPF helper allowing to apply some of these actions on the packet being processed, the helper should be able to call this function, hence the need to make it public. Moreover, if one argument is incorrect or if the next hop can not be found, an error should be returned by the BPF helper so the BPF program can adapt its processing of the packet (return an error, properly force the drop, ...). This patch hence makes this function return dst->error to indicate a possible error. Signed-off-by: Mathieu Xhonneux Acked-by: David Lebrun Signed-off-by: Daniel Borkmann

ipv6: sr: make seg6.h includable without IPv6

2018-05-24T09:57:35+00:00

include/net/seg6.h cannot be included in a source file if CONFIG_IPV6 is not enabled: include/net/seg6.h: In function 'seg6_pernet': >> include/net/seg6.h:52:14: error: 'struct net' has no member named 'ipv6'; did you mean 'ipv4'? return net->ipv6.seg6_data; ^~~~ ipv4 This commit makes seg6_pernet return NULL if IPv6 is not compiled, hence allowing seg6.h to be included regardless of the configuration. Signed-off-by: Mathieu Xhonneux Signed-off-by: Daniel Borkmann

ipv6: sr: add support for ip4ip6 encapsulation

2017-08-26T00:10:23+00:00

This patch enables the SRv6 encapsulation mode to carry an IPv4 payload. All the infrastructure was already present, I just had to add a parameter to seg6_do_srh_encap() to specify the inner packet protocol, and perform some additional checks. Usage example: ip route add 1.2.3.4 encap seg6 mode encap segs fc00::1,fc00::2 dev eth0 Signed-off-by: David Lebrun Signed-off-by: David S. Miller