kernel/linux.git/include/linux/usb, branch v3.12.62

USB: EHCI: declare hostpc register as zero-length array

2016-07-21T06:35:59+00:00

commit 7e8b3dfef16375dbfeb1f36a83eb9f27117c51fd upstream. The HOSTPC extension registers found in some EHCI implementations form a variable-length array, with one element for each port. Therefore the hostpc field in struct ehci_regs should be declared as a zero-length array, not a single-element array. This fixes a problem reported by UBSAN. Signed-off-by: Alan Stern Reported-by: Wilfried Klaebe Tested-by: Wilfried Klaebe Signed-off-by: Jiri Slaby

USB: add quirk for devices with broken LPM

2016-01-05T16:48:51+00:00

commit ad87e03213b552a5c33d5e1e7a19a73768397010 upstream. Some USB device / host controller combinations seem to have problems with Link Power Management. For example, Steinar found that his xHCI controller wouldn't handle bandwidth calculations correctly for two video cards simultaneously when LPM was enabled, even though the bus had plenty of bandwidth available. This patch introduces a new quirk flag for devices that should remain disabled for LPM, and creates quirk entries for Steinar's devices. Signed-off-by: Alan Stern Reported-by: Steinar H. Gunderson Signed-off-by: Jiri Slaby

Revert "USB: Add device quirk for ASUS T100 Base Station keyboard"

2015-10-28T15:38:37+00:00

This reverts commit e25ecd21ffdbf1f8287103ccf97205fc30088344 in 3.12, upstream commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 (USB: Add device quirk for ASUS T100 Base Station keyboard). It was applied twice to 3.12 and one backport is bogus. Cc: Lu Baolu Cc: Alan Stern Cc: Greg Kroah-Hartman Signed-off-by: Jiri Slaby

usb: core: implement AMD remote wakeup quirk

2015-10-28T15:38:35+00:00

commit 7868943db1668fba898cf71bed1506c19d6958aa upstream. The following patch is required to resolve remote wake issues with certain devices. Issue description: If the remote wake is issued from the device in a specific timing condition while the system is entering sleep state then it may cause system to auto wake on subsequent sleep cycle. Root cause: Host controller rebroadcasts the Resume signal > 100 µseconds after receiving the original resume event from the device. For proper function, some devices may require the rebroadcast of resume event within the USB spec of 100µS. Workaroud: 1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb devices are mouse or not. And get out the port id which attached a mouse with Pixart controller. 2. Then reset the port which attached issue device during system resume from S3. [Q] Why the special devices are only mice? Would high speed devices such as 3G modem or USB Bluetooth adapter trigger this issue? - Current this sensitivity is only confined to devices that use Pixart controllers. This controller is designed for use with LS mouse devices only. We have not observed any other devices failing. There may be a small risk for other devices also but this patch (reset device in resume phase) will cover the cases if required. [Q] Shouldn’t the resume signal be sent within 100 us for every device? - The Host controller may not send the resume signal within 100us, this our host controller specification change. This is why we require the patch to prevent side effects on certain known devices. [Q] Why would clicking mouse INTENSELY to wake the system up trigger this issue? - This behavior is specific to the devices that use Pixart controller. It is timing dependent on when the resume event is triggered during the sleep state. [Q] Is it a host controller issue or mouse? - It is the host controller behavior during resume that triggers the device incorrect behavior on the next resume. This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice when they attached to platforms with AMD Yangtze chipset. Signed-off-by: Huang Rui Suggested-by: Alan Stern Acked-by: Alan Stern Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jiri Slaby

usb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN

2015-03-01T22:34:20+00:00

commit 5efd2ea8c9f4f12916ffc8ba636792ce052f6911 upstream. the following error pops up during "testusb -a -t 10" | musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma) hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in hcd_buffer_alloc() returning memory which is 32 bytes aligned and it might by identified by buffer_offset() as another buffer. This means the buffer which is on a 32 byte boundary will not get freed, instead it tries to free another buffer with the error message. This patch fixes the issue by creating the smallest DMA buffer with the size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is smaller). This might be 32, 64 or even 128 bytes. The next three pools will have the size 128, 512 and 2048. In case the smallest pool is 128 bytes then we have only three pools instead of four (and zero the first entry in the array). The last pool size is always 2048 bytes which is the assumed PAGE_SIZE / 2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where we would end up with 8KiB buffer in case we have 16KiB pages. Instead I think it makes sense to have a common size(s) and extend them if there is need to. There is a BUILD_BUG_ON() now in case someone has a minalign of more than 128 bytes. Signed-off-by: Sebastian Andrzej Siewior Acked-by: Alan Stern Signed-off-by: Jiri Slaby

USB: core: add device-qualifier quirk

2014-11-13T18:02:50+00:00

commit 2a159389bf5d962359349a76827b2f683276a1c7 upstream. Add new quirk for devices that cannot handle requests for the device_qualifier descriptor. A USB-2.0 compliant device must respond to requests for the device_qualifier descriptor (even if it's with a request error), but at least one device is known to misbehave after such a request. Suggested-by: Bjørn Mork Signed-off-by: Johan Hovold Signed-off-by: Jiri Slaby

USB: Add device quirk for ASUS T100 Base Station keyboard

2014-10-30T20:31:33+00:00

commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 upstream. This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by: Lu Baolu Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jiri Slaby

USB: Add device quirk for ASUS T100 Base Station keyboard

2014-10-17T07:43:19+00:00

usb-core bInterval quirk

2014-09-02T09:37:54+00:00

commit cd83ce9e6195aa3ea15ab4db92892802c20df5d0 upstream. This patch adds a usb quirk to support devices with interupt endpoints and bInterval values expressed as microframes. The quirk causes the parse endpoint function to modify the reported bInterval to a standards conforming value. There is currently code in the endpoint parser that checks for bIntervals that are outside of the valid range (1-16 for USB 2+ high speed and super speed interupt endpoints). In this case, the code assumes the bInterval is being reported in 1ms frames. As well, the correction is only applied if the original bInterval value is out of the 1-16 range. With this quirk applied to the device, the bInterval will be accurately adjusted from microframes to an exponent. Signed-off-by: James P Michels III Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jiri Slaby

usbnet: include wait queue head in device structure

2014-04-18T09:07:13+00:00

[ Upstream commit 14a0d635d18d0fb552dcc979d6d25106e6541f2e ] This fixes a race which happens by freeing an object on the stack. Quoting Julius: > The issue is > that it calls usbnet_terminate_urbs() before that, which temporarily > installs a waitqueue in dev->wait in order to be able to wait on the > tasklet to run and finish up some queues. The waiting itself looks > okay, but the access to 'dev->wait' is totally unprotected and can > race arbitrarily. I think in this case usbnet_bh() managed to succeed > it's dev->wait check just before usbnet_terminate_urbs() sets it back > to NULL. The latter then finishes and the waitqueue_t structure on its > stack gets overwritten by other functions halfway through the > wake_up() call in usbnet_bh(). The fix is to just not allocate the data structure on the stack. As dev->wait is abused as a flag it also takes a runtime PM change to fix this bug. Signed-off-by: Oliver Neukum Reported-by: Grant Grundler Tested-by: Grant Grundler Signed-off-by: David S. Miller Signed-off-by: Jiri Slaby