kernel/linux.git/include/linux/mmc/sdio.h, branch v6.19.11

mmc: core: Add support for SDIO wakeup interrupt

2022-07-26T14:58:31+00:00

If wakeup-source flag is set in host dts node, parse EAI information from SDIO CCCR interrupt externsion segment for in-band wakeup. If async interrupt is supported by SDIO card then enable it and set enable_async_irq flag in sdio_cccr structure to 1. The parse flow is implemented in sdio_read_cccr(). Reviewed-by: AngeloGioacchino Del Regno Signed-off-by: Axe Yang Link: https://lore.kernel.org/r/20220726062842.18846-3-axe.yang@mediatek.com Signed-off-by: Ulf Hansson

mmc: sdio: fix a typo in the comment of SDIO_SD_REV_3_00

2021-03-30T09:42:03+00:00

I believe "Spev" is typo, should be "Spec". Signed-off-by: Jisheng Zhang Link: https://lore.kernel.org/r/20210311174157.561dada9@xhacker.debian Signed-off-by: Ulf Hansson

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

2019-05-30T18:26:32+00:00

Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman

mmc: sdio: fix setting card data bus width as 4-bit

2012-06-06T13:22:53+00:00

SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width setting as below: 00b: 1-bit bus 01b: Reserved 10b: 4-bit bus 11b: 8-bit bus (only for embedded SDIO) And sdio_enable_wide is for setting data bus width as 4-bit. But currently, it first reads the register, second OR' 1b with SDIO_CCCR_IF[1], and then writes it back. As we can see, this is based on such assumption that the SDIO_CCCR_IF[0] is always 0. Apparently, this is not right. Signed-off-by: Yong Ding Acked-by: Philip Rakity Signed-off-by: Chris Ball

mmc: sdio: support SDIO UHS cards

2012-01-12T04:58:41+00:00

This patch adds support for sdio UHS cards per the version 3.0 spec. UHS mode is only enabled for version 3.0 cards when both the host and the controller support UHS modes. 1.8v signaling support is removed if both the card and the host do not support UHS. This is done to maintain compatibility and some system/card combinations break when 1.8v signaling is enabled when the host does not support UHS. Signed-off-by: Philip Rakity Signed-off-by: Aaron Lu Reviewed-by: Arindam Nath Tested-by: Bing Zhao Signed-off-by: Chris Ball

mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00

2011-10-26T20:32:31+00:00

Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified Specification Version 3.00, Feb. 25, 2011. This patch has been tested with Marvell WLAN device SD8797. Signed-off-by: Bing Zhao Signed-off-by: Chris Ball

mmc: Standardize header file inclusion checks.

2011-07-20T21:20:48+00:00

Standardize the checks for multiple MMC header file inclusion, including adding comments to terminating #endif's, and fixing one incorrect comment. Signed-off-by: Robert P. J. Day Signed-off-by: Chris Ball

mmc: avoid getting CID on SDIO-only cards

2010-09-10T01:57:22+00:00

The introduction of support for SD combo cards breaks the initialization of all CSR SDIO chips. The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR chips to be reset (this is non-standard behavior). When initializing an SDIO card check for a combo card by using the memory present bit in the R4 response to IO_SEND_OP_COND (CMD5). This avoids the call to mmc_sd_get_cid() on an SDIO-only card. Signed-off-by: David Vrabel Acked-by: Michal Mirolaw Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem

2010-04-15T20:21:34+00:00

Conflicts: Documentation/feature-removal-schedule.txt drivers/net/wireless/ath/ath5k/phy.c drivers/net/wireless/wl12xx/wl1271_main.c

libertas/sdio: 8686: set ECSI bit for 1-bit transfers

2010-04-06T20:52:06+00:00

When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line. However, the 8686 will only drive this line when the ECSI bit is set in the CCCR_IF register. Thanks to Alagu Sankar for pointing me in the right direction. Signed-off-by: Daniel Mack Cc: Alagu Sankar Cc: Volker Ernst Cc: Dan Williams Cc: John W. Linville Cc: Holger Schurig Cc: Bing Zhao Cc: libertas-dev@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: linux-mmc@vger.kernel.org Acked-by: Dan Williams Signed-off-by: John W. Linville