kernel/linux.git/include/linux/mmc/host.h, branch v4.0.7

mmc: core: Initial support for MMC power sequences

2015-01-28T11:31:12+00:00

System on chip designs may specify a specific MMC power sequence. To successfully detect an (e)MMC/SD/SDIO card, that power sequence must be followed while initializing the card. To be able to handle these SOC specific power sequences, let's add a MMC power sequence interface. It provides the following functions to help the mmc core to deal with these power sequences. mmc_pwrseq_alloc() - Invoked from mmc_of_parse(), to initialize data. mmc_pwrseq_pre_power_on()- Invoked in the beginning of mmc_power_up(). mmc_pwrseq_post_power_on()- Invoked at the end in mmc_power_up(). mmc_pwrseq_power_off()- Invoked from mmc_power_off(). mmc_pwrseq_free() - Invoked from mmc_free_host(), to free data. Each MMC power sequence provider will be responsible to implement a set of callbacks. These callbacks mirrors the functions above. This patch adds the skeleton, following patches will extend the core of the MMC power sequence and add support for a specific simple MMC power sequence. Do note, since the mmc_pwrseq_alloc() is invoked from mmc_of_parse(), host drivers needs to make use of this API to enable the support for MMC power sequences. Moreover the MMC power sequence support depends on CONFIG_OF. Signed-off-by: Ulf Hansson Tested-by: Javier Martinez Canillas Reviewed-by: Javier Martinez Canillas

mmc: slot-gpio: Rework how to handle allocation of slot-gpio data

2015-01-19T08:56:18+00:00

By moving the allocation of the slot-gpio data into mmc_alloc_host(), we can remove the slot-gpio internal calls to mmc_gpio_alloc(). This means mmc_gpio_alloc() has now only one caller left, which consequence allow us to simplify and remove some of the slot-gpio code. Additionally, this makes the slot-gpio mutex redundant, so let's remove it. Signed-off-by: Ulf Hansson

mmc: sdhci: Clear also HS400 1.2V capability if 1.2V is not supported

2014-11-26T13:30:51+00:00

1.2V HS200 mode capability is cleared if there is not a voltage regulator that supports 1.2V. Do the same for 1.2V HS400 mode. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: core: Add new power_mode MMC_POWER_UNDEFINED

2014-09-24T09:20:04+00:00

Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as the initial value of host->ios.power_mode. For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later mmc_power_off() do real power-off things instead of NOP, and further prevents state messed up in cards that was already initialized (eg. by BIOS of UEFI driver). Signed-off-by: Roger Tseng Signed-off-by: Ulf Hansson

mmc: remove MMC_CAP2_NO_MULTI_READ flags

2014-09-09T12:15:43+00:00

Now, mmc framework uses multi_io_quirk for I/O HW bug workaround. MMC_CAP2_NO_MULTI_READ flag is no longer needed Signed-off-by: Kuninori Morimoto Signed-off-by: Ulf Hansson

mmc: Add .multi_io_quirk callback for multi I/O HW bug

2014-09-09T11:59:25+00:00

Historically, we have been using MMC_CAP* to handle host HW issues and currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi I/O HW bug workaround. There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all situations. Therefore let's add an optional host ops callback to enable host drivers to return the number of blocks it allows per request. In a future patch and when host drivers have converted to the new callback, MMC_CAP2_NO_MULTI_READ shall be removed. Signed-off-by: Kuninori Morimoto Signed-off-by: Ulf Hansson

mmc: implement Driver Stage Register handling

2014-09-09T11:59:07+00:00

Some eMMC and SD cards implement a DSR register that allows to tune raise/fall times and drive strength of the CMD and DATA outputs. The values to use depend on the card in use and the host. It might be needed to reduce the drive strength to prevent voltage peaks above the host's specification. Implement a 'dsr' devicetree property that allows to specify the value to set the DSR to. For non-dt setups the new members of mmc_host can be set by board code. This patch was initially authored by Sascha Hauer. It contains improvements authored by Markus Niebel and Uwe Kleine-König. Signed-off-by: Sascha Hauer Signed-off-by: Markus Niebel Signed-off-by: Uwe Kleine-König Signed-off-by: Ulf Hansson

mmc: sdio_irq: rework sdio irq handling

2014-05-22T11:26:03+00:00

Rather than the SDIO support spawning it's own thread for handling card interrupts, use the generic IRQ infrastructure for this, triggering it from the host interface's interrupt handling directly. This avoids a race between the parent thread waiting to receive an interrupt response from the card, and the slow startup from the sdio irq thread, which can occur as a result of high system load (eg, while udev is running.) Signed-off-by: Russell King Tested-by: Markus Pargmann Tested-by: Stephen Warren [Ulf Hansson] Resolved conflict Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: core: Improve support for deferred regulators

2014-05-12T22:08:24+00:00

Callers of mmc_regulator_get_supply could benefit from knowing if either of the regulators are present but not yet available. Since callers do not currently examine the return value, modify this function to return zero or -EPROBE_DEFER if either regulator get returns the same. Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal with absent regulators, switch to devm_regulator_get_optional. This has the added benefit of allowing this function to behave correctly even in the !CONFIG_REGULATOR case such that the stub can be removed. Signed-off-by: Tim Kryger Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: add support for HS400 mode of eMMC5.0

2014-05-12T22:06:06+00:00

This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon Reviewed-by: Jackey Shen Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball