kernel/linux.git/include/linux/mmc/core.h, branch v3.1.4

mmc: core: add non-blocking mmc request function

2011-07-20T21:21:10+00:00

Previously there has only been one function mmc_wait_for_req() to start and wait for a request. This patch adds: * mmc_start_req() - starts a request wihtout waiting If there is on ongoing request wait for completion of that request and start the new one and return. Does not wait for the new command to complete. This patch also adds new function members in struct mmc_host_ops only called from core.c: * pre_req - asks the host driver to prepare for the next job * post_req - asks the host driver to clean up after a completed job The intention is to use pre_req() and post_req() to do cache maintenance while a request is active. pre_req() can be called while a request is active to minimize latency to start next job. post_req() can be used after the next job is started to clean up the request. This will minimize the host driver request end latency. post_req() is typically used before ending the block request and handing over the buffer to the block layer. Add a host-private member in mmc_data to be used by pre_req to mark the data. The host driver will then check this mark to see if the data is prepared or not. Signed-off-by: Per Forlin Acked-by: Kyungmin Park Acked-by: Arnd Bergmann Reviewed-by: Venkatraman S Tested-by: Sourav Poddar Tested-by: Linus Walleij Signed-off-by: Chris Ball

mmc: queue: let host controllers specify maximum discard timeout

2011-07-20T21:21:03+00:00

Some host controllers will not operate without a hardware timeout that is limited in value. However large discards require large timeouts, so there needs to be a way to specify the maximum discard size. A host controller driver may now specify the maximum discard timeout possible so that max_discard_sectors can be calculated. However, for eMMC when the High Capacity Erase Group Size is not in use, the timeout calculation depends on clock rate which may change. For that case Preferred Erase Size is used instead. Signed-off-by: Adrian Hunter Signed-off-by: Chris Ball

mmc: Standardize header file inclusion checks.

2011-07-20T21:20:48+00:00

Standardize the checks for multiple MMC header file inclusion, including adding comments to terminating #endif's, and fixing one incorrect comment. Signed-off-by: Robert P. J. Day Signed-off-by: Chris Ball

mmc: core: Use CMD23 for multiblock transfers when we can.

2011-05-25T20:48:46+00:00

CMD23-prefixed instead of open-ended multiblock transfers have a performance advantage on some MMC cards. Signed-off-by: Andrei Warkentin Signed-off-by: Chris Ball

mmc: core: Add mmc CMD+ACMD passthrough ioctl

2011-05-25T01:02:54+00:00

Allows appropriately-privileged applications to send CMD (normal) and ACMD (application-specific; preceded with CMD55) commands to cards/devices on the mmc bus. This is primarily useful for enabling the security functionality built in to every SD card. It can also be used as a generic passthrough (e.g. to enable virtual machines to control mmc bus devices directly). However, this use case has not been tested rigorously. Generic passthrough testing was only conducted for a few non-security opcodes to prove the feasibility of the passthrough. Since any opcode can be sent using this passthrough, it is very possible to render the card/device unusable. Applications that use this ioctl must have CAP_SYS_RAWIO. Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC, TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC. Signed-off-by: John Calixto Reviewed-by: Andrei Warkentin Reviewed-by: Arnd Bergmann Signed-off-by: Chris Ball

mmc: core: Allow setting CMD timeout for CMD6 (SWITCH).

2011-05-25T01:01:13+00:00

CMD6 is an R1B-type command, where DAT is used as busy. Depending on register written using CMD6, timeout value can be different as per spec. Signed-off-by: Andrei Warkentin Signed-off-by: Chris Ball

mmc: core: Rename erase_timeout to cmd_timeout_ms.

2011-05-25T01:01:05+00:00

Renames erase_timeout to cmd_timeout_ms inside struct mmc_command. First step to making host honor timeouts for non-data-transfer commands. Cleans up erase timeout code. Signed-off-by: Andrei Warkentin Signed-off-by: Chris Ball

mmc: core: export function mmc_do_release_host()

2011-03-17T19:35:11+00:00

When using mmc_try_claim_host the corresponding release function is mmc_do_release_host, which then also must be exported. Reviewed-by: Jonas Aberg Reviewed-by: Sebastian Rasmussen Signed-off-by: Ulf Hansson Signed-off-by: Linus Walleij Signed-off-by: Chris Ball

mmc: Fixes for Dual Data Rate (DDR) support

2010-10-23T13:11:16+00:00

The DDR support patch needs the following fixes: - The block driver does not need to know about DDR, any more than it needs to know about bus width. - Not only the card must be switched to DDR mode. The host controller must also be configured, which is done through the 'set_ios()' function. - Do not set the DDR mode state until after the switch command is successful. - Setting block length is not supported in DDR mode. Make that a core function and change the other place it is used (mmc_test) also. Signed-off-by: Adrian Hunter Signed-off-by: Chris Ball

mmc: MMC 4.4 DDR support

2010-10-23T13:11:16+00:00

Add support for Dual Data Rate MMC cards as defined in the 4.4 specification. Signed-off-by: Hanumath Prasad Cc: linux-mmc@vger.kernel.org Acked-by: Linus Walleij Tested-by Zhangfei Gao Signed-off-by: Chris Ball