kernel/linux.git/include/linux/i2c, branch v2.6.30

i2c: xtensa s6000 i2c driver

2009-04-07T09:23:34+00:00

Support for the s6000 on-chip i2c controller. Signed-off-by: Oskar Schirmer Signed-off-by: Daniel Glöckner Signed-off-by: Ben Dooks

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6

2009-04-03T17:39:20+00:00

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (32 commits) regulator: twl4030 VAUX3 supports 3.0V regulator: Support disabling of unused regulators by machines regulator: Don't increment use_count for boot_on regulators twl4030-regulator: expose VPLL2 regulator: refcount fixes regulator: Don't warn if we failed to get a regulator regulator: Allow boot_on regulators to be disabled by clients regulator: Implement list_voltage for WM835x LDOs and DCDCs twl4030-regulator: list more VAUX4 voltages regulator: Don't warn on omitted voltage constraints regulator: Implement list_voltage() for WM8400 DCDCs and LDOs MMC: regulator utilities regulator: twl4030 voltage enumeration (v2) regulator: twl4030 regulators regulator: get_status() grows kerneldoc regulator: enumerate voltages (v2) regulator: Fix get_mode() for WM835x DCDCs regulator: Allow regulators to set the initial operating mode regulator: Suggest use of datasheet supply or pin names for consumers regulator: email - update email address and regulator webpage. ...

memory_accessor: implement the new memory_accessor interface for I2C EEPROM

2009-04-03T02:04:50+00:00

In the case of at24, the platform code registers a 'setup' callback with the at24_platform_data. When the at24 driver detects an EEPROM, it fills out the read and write functions of the memory_accessor and calls the setup callback passing the memory_accessor struct. The platform code can then use the read/write functions in the memory_accessor struct for reading and writing the EEPROM. Signed-off-by: Kevin Hilman Cc: David Brownell Cc: Jean Delvare Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

regulator: twl4030 regulators

2009-03-31T08:56:25+00:00

Support most of the LDO regulators in the twl4030 family chips. In the case of LDOs supporting MMC/SD, the voltage controls are used; but in most other cases, the regulator framework is only used to enable/disable a supplies, conserving power when a given voltage rail is not needed. The drivers/mfd/twl4030-core.c code already sets up the various regulators according to board-specific configuration, and knows that some chips don't provide the full set of voltage rails. The omitted regulators are intended to be under hardware control, such as during the hardware-mediated system powerup, powerdown, and suspend states. Unless/until software hooks are known to be safe, they won't be exported here. These regulators implement the new get_status() operation, but can't realistically implement get_mode(); the status output is effectively the result of a vote, with the relevant hardware inputs not exposed. Signed-off-by: David Brownell Acked-by: Mark Brown Signed-off-by: Liam Girdwood

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2009-01-07T01:14:01+00:00

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits) Input: i8042 - add Dell Vostro 1510 to nomux list Input: gtco - use USB endpoint API Input: add support for Maple controller as a joystick Input: atkbd - broaden the Dell DMI signatures Input: HIL drivers - add MODULE_ALIAS() Input: map_to_7segment.h - convert to __inline__ for userspace Input: add support for enhanced rotary controller on pxa930 and pxa935 Input: add support for trackball on pxa930 and pxa935 Input: add da9034 touchscreen support Input: ads7846 - strict_strtoul takes unsigned long Input: make some variables and functions static Input: add tsc2007 based touchscreen driver Input: psmouse - add module parameters to control OLPC touchpad delays Input: i8042 - add Gigabyte M912 netbook to noloop exception table Input: atkbd - Samsung NC10 key repeat fix Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop Input: libps2 - handle 0xfc responses from devices Input: add support for Wacom W8001 penabled serial touchscreen Input: synaptics - report multi-taps only if supported by the device Input: add joystick driver for Walkera WK-0701 RC transmitter ...

twl4030-gpio: cleanup debounce

2009-01-06T23:59:25+00:00

Provide a static debounce configuration mechanism for twl4030 GPIOs, replacing the previous dynamic one. The single user of that mechanism was for MMC card detect debouncing. Boards can provide a bitmask saying which GPIOs to debounce (30 msec). It's always enabled for pins with the MMC card-detect/VMMCx link active, so most boards won't need to set the debounce mask. This is a net code shrink, including runtime footprint. Signed-off-by: David Brownell Signed-off-by: Tony Lindgren Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

mfd: dm355evm msp430 driver

2009-01-04T11:17:43+00:00

Basic MFD framework for the MSP430 microcontroller firmware used on the dm355evm board: - Provides an interface for other drivers: register read/write utilities, and register declarations. - Directly exports: * Many signals through the GPIO framework + LEDs + SW6 through gpio sysfs + NTSC/nPAL jumper through gpio sysfs + ... more could be added later, e.g. MMC signals * Child devices: + LEDs, via leds-gpio child (and default triggers) + RTC, via rtc-dm355evm child device + Buttons and IR control, via dm355evm_keys - Supports power-off system call. Use the reset button to power the board back up; the power supply LED will be on, but the MSP430 waits to re-activate the regulators. - On probe() this: * Announces firmware revision * Turns off the banked LEDs * Exports the resources noted above * Hooks the power-off support * Muxes tvp5146 -or- imager for video input Unless the new tvp514x driver (tracked for mainline) is configured, this assumes that some custom imager driver handles video-in. This completely ignores the registers reporting the output voltages on the various power supplies. Someone could add a hwmon interface if that seems useful. Signed-off-by: David Brownell Signed-off-by: Samuel Ortiz

mfd: twl4030 regulator bug fixes

2009-01-04T11:17:40+00:00

This contains two bugfixes to the initial twl4030 regulator support patch related to USB: (a) always overwrite the old list of consumers ... else the regulator handles all use the same "usb1v5" name; (b) don't set up the "usbcp" regulator, which turns out to be managed through separate controls, usually ULPI directly from the OTG controller. Signed-off-by: David Brownell Signed-off-by: Samuel Ortiz

mfd: twl4030: create some regulator devices

2009-01-04T11:17:39+00:00

Initial code to create twl4030 voltage regulator devices, using the new regulator framework. Note that this now starts to care what name is used to declare the TWL chip: - TWL4030 is the "old" chip; newer ones have a bigger variety of VAUX2 voltages. - TWL5030 is the core "new" chip; TPS65950 is its catalog version. - The TPS65930 and TPS65920 are cost-reduced catalog versions of TWL5030 parts ... fewer regulators, no battery charger, etc. Board-specific regulator configuration should be provided, listing which regulators are used and their constraints (e.g. 1.8V only). Code that could ("should"?) leverage the regulator stuff includes TWL4030 USB transceiver support and MMC glue, LCD support for the 3430SDP and Labrador boards, and S-Video output. Signed-off-by: David Brownell Signed-off-by: Tony Lindgren Signed-off-by: Samuel Ortiz

mfd: twl4030: cleanup symbols and OMAP dependency

2009-01-04T11:17:39+00:00

Finish removing dependency of TWL driver stack on platform-specific IRQ definitions ... and remove the build dependency on OMAP. This lets the TWL4030 code be included in test builds for most platforms, and will make it easier for non-OMAP folk to update most of this code for new APIs etc. Signed-off-by: David Brownell Signed-off-by: Tony Lindgren Signed-off-by: Samuel Ortiz