kernel/linux.git/drivers, branch v6.4.15

pinctrl: amd: Don't show `Invalid config param` errors

2023-09-06T20:25:33+00:00

commit 87b549efcb0f7934b0916d2a00607a878b6f1e0f upstream. On some systems amd_pinconf_set() is called with parameters 0x8 (PIN_CONFIG_DRIVE_PUSH_PULL) or 0x14 (PIN_CONFIG_PERSIST_STATE) which are not supported by pinctrl-amd. Don't show an err message when called with an invalid parameter, downgrade this to debug instead. Cc: stable@vger.kernel.org # 6.1 Fixes: 635a750d958e1 ("pinctrl: amd: Use amd_pinconf_set() for all config options") Signed-off-by: Mario Limonciello Link: https://lore.kernel.org/r/20230717201652.17168-1-mario.limonciello@amd.com Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman

usb: typec: tcpci: clear the fault status bit

2023-09-06T20:25:33+00:00

commit 23e60c8daf5ec2ab1b731310761b668745fcf6ed upstream. According the "USB Type-C Port Controller Interface Specification v2.0" the TCPC sets the fault status register bit-7 (AllRegistersResetToDefault) once the registers have been reset to their default values. This triggers an alert(-irq) on PTN5110 devices albeit we do mask the fault-irq, which may cause a kernel hang. Fix this generically by writing a one to the corresponding bit-7. Cc: stable@vger.kernel.org Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)") Reported-by: "Angus Ainslie (Purism)" Closes: https://lore.kernel.org/all/20190508002749.14816-2-angus@akkea.ca/ Reported-by: Christian Bach Closes: https://lore.kernel.org/regressions/ZR0P278MB07737E5F1D48632897D51AC3EB329@ZR0P278MB0773.CHEP278.PROD.OUTLOOK.COM/t/ Signed-off-by: Marco Felsch Signed-off-by: Fabio Estevam Reviewed-by: Guenter Roeck Link: https://lore.kernel.org/r/20230816172502.1155079-1-festevam@gmail.com Signed-off-by: Greg Kroah-Hartman

tcpm: Avoid soft reset when partner does not support get_status

2023-09-06T20:25:32+00:00

commit 78e0ea4277546debf7e96797ac3b768539cc44f6 upstream. When partner does not support get_status message, tcpm right now responds with soft reset message. This causes PD renegotiation to happen and resets PPS link. Avoid soft resetting the link when partner does not support get_status message to mitigate PPS resets. [ 208.926752] Setting voltage/current limit 9500 mV 2450 mA [ 208.930407] set_auto_vbus_discharge_threshold mode:3 pps_active:y vbus:9500 ret:0 [ 208.930418] state change SNK_TRANSITION_SINK -> SNK_READY [rev3 POWER_NEGOTIATION] [ 208.930455] AMS POWER_NEGOTIATION finished // ALERT message from the Source [ 213.948442] PD RX, header: 0x19a6 [1] [ 213.948451] state change SNK_READY -> GET_STATUS_SEND [rev3 GETTING_SOURCE_SINK_STATUS] [ 213.948457] PD TX, header: 0x492 [ 213.950402] PD TX complete, status: 0 [ 213.950427] pending state change GET_STATUS_SEND -> GET_STATUS_SEND_TIMEOUT @ 60 ms [rev3 GETTING_SOURCE_SINK_STATUS] // NOT_SUPPORTED from the Source [ 213.959954] PD RX, header: 0xbb0 [1] // sink sends SOFT_RESET [ 213.959958] state change GET_STATUS_SEND -> SNK_SOFT_RESET [rev3 GETTING_SOURCE_SINK_STATUS] [ 213.959962] AMS GETTING_SOURCE_SINK_STATUS finished [ 213.959964] AMS SOFT_RESET_AMS start [ 213.959966] state change SNK_SOFT_RESET -> AMS_START [rev3 SOFT_RESET_AMS] [ 213.959969] state change AMS_START -> SOFT_RESET_SEND [rev3 SOFT_RESET_AMS] Cc: stable@vger.kernel.org Fixes: 8dea75e11380 ("usb: typec: tcpm: Protocol Error handling") Signed-off-by: Badhri Jagan Sridharan Acked-by: Heikki Krogerus Link: https://lore.kernel.org/r/20230820044449.1005889-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman

fsi: master-ast-cf: Add MODULE_FIRMWARE macro

2023-09-06T20:25:32+00:00

commit 3a1d7aff6e65ad6e285e28abe55abbfd484997ee upstream. The module loads firmware so add a MODULE_FIRMWARE macro to provide that information via modinfo. Fixes: 6a794a27daca ("fsi: master-ast-cf: Add new FSI master using Aspeed ColdFire") Cc: stable@vger.kernel.org # 4.19+ Signed-off-by: Juerg Haefliger Link: https://lore.kernel.org/r/20230628095039.26218-1-juerg.haefliger@canonical.com Signed-off-by: Joel Stanley Signed-off-by: Greg Kroah-Hartman

firmware: stratix10-svc: Fix an NULL vs IS_ERR() bug in probe

2023-09-06T20:25:32+00:00

commit dd218433f2b635d97e8fda3eed047151fd528ce4 upstream. The devm_memremap() function returns error pointers. It never returns NULL. Fix the check. Fixes: 7ca5ce896524 ("firmware: add Intel Stratix10 service layer driver") Cc: stable@vger.kernel.org Signed-off-by: Wang Ming Signed-off-by: Dinh Nguyen Link: https://lore.kernel.org/r/20230727193750.983795-1-dinguyen@kernel.org Signed-off-by: Greg Kroah-Hartman

serial: sc16is7xx: fix bug when first setting GPIO direction

2023-09-06T20:25:32+00:00

commit 9baeea723c0fb9c3ba9a336369f758ed9bc6831d upstream. When configuring a pin as an output pin with a value of logic 0, we end up as having a value of logic 1 on the output pin. Setting a logic 0 a second time (or more) after that will correctly output a logic 0 on the output pin. By default, all GPIO pins are configured as inputs. When we enter sc16is7xx_gpio_direction_output() for the first time, we first set the desired value in IOSTATE, and then we configure the pin as an output. The datasheet states that writing to IOSTATE register will trigger a transfer of the value to the I/O pin configured as output, so if the pin is configured as an input, nothing will be transferred. Therefore, set the direction first in IODIR, and then set the desired value in IOSTATE. This is what is done in NXP application note AN10587. Fixes: dfeae619d781 ("serial: sc16is7xx") Cc: stable@vger.kernel.org Signed-off-by: Hugo Villeneuve Reviewed-by: Lech Perczak Tested-by: Lech Perczak Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com Signed-off-by: Greg Kroah-Hartman

serial: sc16is7xx: fix broken port 0 uart init

2023-09-06T20:25:32+00:00

commit 2861ed4d6e6d1a2c9de9bf5b0abd996c2dc673d0 upstream. The sc16is7xx_config_rs485() function is called only for the second port (index 1, channel B), causing initialization problems for the first port. For the sc16is7xx driver, port->membase and port->mapbase are not set, and their default values are 0. And we set port->iobase to the device index. This means that when the first device is registered using the uart_add_one_port() function, the following values will be in the port structure: port->membase = 0 port->mapbase = 0 port->iobase = 0 Therefore, the function uart_configure_port() in serial_core.c will exit early because of the following check: /* * If there isn't a port here, don't do anything further. */ if (!port->iobase && !port->mapbase && !port->membase) return; Typically, I2C and SPI drivers do not set port->membase and port->mapbase. The max310x driver sets port->membase to ~0 (all ones). By implementing the same change in this driver, uart_configure_port() is now correctly executed for all ports. Fixes: dfeae619d781 ("serial: sc16is7xx") Cc: stable@vger.kernel.org Signed-off-by: Hugo Villeneuve Reviewed-by: Ilpo Järvinen Reviewed-by: Lech Perczak Tested-by: Lech Perczak Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com Signed-off-by: Greg Kroah-Hartman

serial: qcom-geni: fix opp vote on shutdown

2023-09-06T20:25:31+00:00

commit 8ece7b754bc34ffd7fcc8269ccb9128e72ca76d8 upstream. The operating-performance-point vote needs to be dropped when shutting down the port to avoid wasting power by keeping resources like power domains in an unnecessarily high performance state (e.g. when a UART connected Bluetooth controller is not in use). Fixes: a5819b548af0 ("tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state") Cc: stable@vger.kernel.org # 5.9 Cc: Rajendra Nayak Cc: Matthias Kaehlcke Signed-off-by: Johan Hovold Acked-by: Konrad Dybcio Link: https://lore.kernel.org/r/20230714130214.14552-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman

wifi: ath11k: Cleanup mac80211 references on failure during tx_complete

2023-09-06T20:25:31+00:00

commit 29d15589f084d71a4ea8c544039c5839db0236e2 upstream. When a function is using functions from mac80211 to free an skb then it should do it consistently and not switch to the generic dev_kfree_skb_any (or similar functions). Otherwise (like in the error handlers), mac80211 will will not be aware of the freed skb and thus not clean up related information in its internal data structures. Not doing so lead in the past to filled up structure which then prevented new clients to connect. Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Fixes: 6257c702264c ("wifi: ath11k: fix tx status reporting in encap offload mode") Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20230802-ath11k-ack_status_leak-v2-2-c0af729d6229@narfation.org Signed-off-by: Greg Kroah-Hartman

wifi: ath11k: Don't drop tx_status when peer cannot be found

2023-09-06T20:25:31+00:00

commit 400ece6c7f346b0a30867bd00b03b5b2563d4357 upstream. When a station idles for a long time, hostapd will try to send a QoS Null frame to the station as "poll". NL80211_CMD_PROBE_CLIENT is used for this purpose. And the skb will be added to ack_status_frame - waiting for a completion via ieee80211_report_ack_skb(). But when the peer was already removed before the tx_complete arrives, the peer will be missing. And when using dev_kfree_skb_any (instead of going through mac80211), the entry will stay inside ack_status_frames. This IDR will therefore run full after 8K request were generated for such clients. At this point, the access point will then just stall and not allow any new clients because idr_alloc() for ack_status_frame will fail. ieee80211_free_txskb() on the other hand will (when required) call ieee80211_report_ack_skb() and make sure that (when required) remove the entry from the ack_status_frame. Tested-on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Fixes: 6257c702264c ("wifi: ath11k: fix tx status reporting in encap offload mode") Fixes: 94739d45c388 ("ath11k: switch to using ieee80211_tx_status_ext()") Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20230802-ath11k-ack_status_leak-v2-1-c0af729d6229@narfation.org Signed-off-by: Greg Kroah-Hartman