kernel/linux.git/drivers, branch v5.15.72

drm/i915/gem: Really move i915_gem_context.link under ref protection

2022-10-05T08:39:44+00:00

commit d119888b09bd567e07c6b93a07f175df88857e02 upstream. i915_perf assumes that it can use the i915_gem_context reference to protect its i915->gem.contexts.list iteration. However, this requires that we do not remove the context from the list until after we drop the final reference and release the struct. If, as currently, we remove the context from the list during context_close(), the link.next pointer may be poisoned while we are holding the context reference and cause a GPF: [ 4070.573157] i915 0000:00:02.0: [drm:i915_perf_open_ioctl [i915]] filtering on ctx_id=0x1fffff ctx_id_mask=0x1fffff [ 4070.574881] general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] PREEMPT SMP [ 4070.574897] CPU: 1 PID: 284392 Comm: amd_performance Tainted: G E 5.17.9 #180 [ 4070.574903] Hardware name: Intel Corporation NUC7i5BNK/NUC7i5BNB, BIOS BNKBL357.86A.0052.2017.0918.1346 09/18/2017 [ 4070.574907] RIP: 0010:oa_configure_all_contexts.isra.0+0x222/0x350 [i915] [ 4070.574982] Code: 08 e8 32 6e 10 e1 4d 8b 6d 50 b8 ff ff ff ff 49 83 ed 50 f0 41 0f c1 04 24 83 f8 01 0f 84 e3 00 00 00 85 c0 0f 8e fa 00 00 00 <49> 8b 45 50 48 8d 70 b0 49 8d 45 50 48 39 44 24 10 0f 85 34 fe ff [ 4070.574990] RSP: 0018:ffffc90002077b78 EFLAGS: 00010202 [ 4070.574995] RAX: 0000000000000002 RBX: 0000000000000002 RCX: 0000000000000000 [ 4070.575000] RDX: 0000000000000001 RSI: ffffc90002077b20 RDI: ffff88810ddc7c68 [ 4070.575004] RBP: 0000000000000001 R08: ffff888103242648 R09: fffffffffffffffc [ 4070.575008] R10: ffffffff82c50bc0 R11: 0000000000025c80 R12: ffff888101bf1860 [ 4070.575012] R13: dead0000000000b0 R14: ffffc90002077c04 R15: ffff88810be5cabc [ 4070.575016] FS: 00007f1ed50c0780(0000) GS:ffff88885ec80000(0000) knlGS:0000000000000000 [ 4070.575021] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4070.575025] CR2: 00007f1ed5590280 CR3: 000000010ef6f005 CR4: 00000000003706e0 [ 4070.575029] Call Trace: [ 4070.575033] [ 4070.575037] lrc_configure_all_contexts+0x13e/0x150 [i915] [ 4070.575103] gen8_enable_metric_set+0x4d/0x90 [i915] [ 4070.575164] i915_perf_open_ioctl+0xbc0/0x1500 [i915] [ 4070.575224] ? asm_common_interrupt+0x1e/0x40 [ 4070.575232] ? i915_oa_init_reg_state+0x110/0x110 [i915] [ 4070.575290] drm_ioctl_kernel+0x85/0x110 [ 4070.575296] ? update_load_avg+0x5f/0x5e0 [ 4070.575302] drm_ioctl+0x1d3/0x370 [ 4070.575307] ? i915_oa_init_reg_state+0x110/0x110 [i915] [ 4070.575382] ? gen8_gt_irq_handler+0x46/0x130 [i915] [ 4070.575445] __x64_sys_ioctl+0x3c4/0x8d0 [ 4070.575451] ? __do_softirq+0xaa/0x1d2 [ 4070.575456] do_syscall_64+0x35/0x80 [ 4070.575461] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 4070.575467] RIP: 0033:0x7f1ed5c10397 [ 4070.575471] Code: 3c 1c e8 1c ff ff ff 85 c0 79 87 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a9 da 0d 00 f7 d8 64 89 01 48 [ 4070.575478] RSP: 002b:00007ffd65c8d7a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 4070.575484] RAX: ffffffffffffffda RBX: 0000000000000006 RCX: 00007f1ed5c10397 [ 4070.575488] RDX: 00007ffd65c8d7c0 RSI: 0000000040106476 RDI: 0000000000000006 [ 4070.575492] RBP: 00005620972f9c60 R08: 000000000000000a R09: 0000000000000005 [ 4070.575496] R10: 000000000000000d R11: 0000000000000246 R12: 000000000000000a [ 4070.575500] R13: 000000000000000d R14: 0000000000000000 R15: 00007ffd65c8d7c0 [ 4070.575505] [ 4070.575507] Modules linked in: nls_ascii(E) nls_cp437(E) vfat(E) fat(E) i915(E) x86_pkg_temp_thermal(E) intel_powerclamp(E) crct10dif_pclmul(E) crc32_pclmul(E) crc32c_intel(E) aesni_intel(E) crypto_simd(E) intel_gtt(E) cryptd(E) ttm(E) rapl(E) intel_cstate(E) drm_kms_helper(E) cfbfillrect(E) syscopyarea(E) cfbimgblt(E) intel_uncore(E) sysfillrect(E) mei_me(E) sysimgblt(E) i2c_i801(E) fb_sys_fops(E) mei(E) intel_pch_thermal(E) i2c_smbus(E) cfbcopyarea(E) video(E) button(E) efivarfs(E) autofs4(E) [ 4070.575549] ---[ end trace 0000000000000000 ]--- v3: fix incorrect syntax of spin_lock() replacing spin_lock_irqsave() v2: irqsave not required in a worker, neither conversion to irq safe elsewhere (Tvrtko), - perf: it's safe to call gen8_configure_context() even if context has been closed, no need to check, - drop unrelated cleanup (Andi, Tvrtko) Reported-by: Mark Janes Closes: https://gitlab.freedesktop.org/drm/intel/issues/6222 References: a4e7ccdac38e ("drm/i915: Move context management under GEM") Fixes: f8246cf4d9a9 ("drm/i915/gem: Drop free_work for GEM contexts") Signed-off-by: Chris Wilson Reviewed-by: Andi Shyti Signed-off-by: Janusz Krzysztofik Cc: Tvrtko Ursulin Cc: # v5.12+ Signed-off-by: Andi Shyti Link: https://patchwork.freedesktop.org/patch/msgid/20220916092403.201355-3-janusz.krzysztofik@linux.intel.com (cherry picked from commit ad3aa7c31efa5a09b0dba42e66cfdf77e0db7dc2) Signed-off-by: Rodrigo Vivi [janusz: backport] Signed-off-by: Janusz Krzysztofik Signed-off-by: Greg Kroah-Hartman

clk: iproc: Do not rely on node name for correct PLL setup

2022-10-05T08:39:44+00:00

[ Upstream commit 1b24a132eba7a1c19475ba2510ec1c00af3ff914 ] After commit 31fd9b79dc58 ("ARM: dts: BCM5301X: update CRU block description") a warning from clk-iproc-pll.c was generated due to a duplicate PLL name as well as the console stopped working. Upon closer inspection it became clear that iproc_pll_clk_setup() used the Device Tree node unit name as an unique identifier as well as a parent name to parent all clocks under the PLL. BCM5301X was the first platform on which that got noticed because of the DT node unit name renaming but the same assumptions hold true for any user of the iproc_pll_clk_setup() function. The first 'clock-output-names' property is always guaranteed to be unique as well as providing the actual desired PLL clock name, so we utilize that to register the PLL and as a parent name of all children clock. Fixes: 5fe225c105fd ("clk: iproc: add initial common clock support") Signed-off-by: Florian Fainelli Acked-by: Rafał Miłecki Link: https://lore.kernel.org/r/20220905161504.1526-1-f.fainelli@gmail.com Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks

2022-10-05T08:39:44+00:00

[ Upstream commit b1ff1bfe81e763420afd5f3f25f0b3cbfd97055c ] There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag should not be used. For instance, the default parent clock for QSPI is pll2_bus, which is also the parent clock for quite a few modules, such as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system hang due to pll2_bus rate changed. Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API") Signed-off-by: Han Xu Link: https://lore.kernel.org/r/20220915150959.3646702-1-han.xu@nxp.com Tested-by: Fabio Estevam Reviewed-by: Abel Vesa Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

vdpa/ifcvf: fix the calculation of queuepair

2022-10-05T08:39:43+00:00

[ Upstream commit db5db1a00d0816207be3a0166fcb4f523eaf3b52 ] The q_pair_id to address a queue pair in the lm bar should be calculated by queue_id / 2 rather than queue_id / nr_vring. Fixes: 2ddae773c93b ("vDPA/ifcvf: detect and use the onboard number of queues directly") Signed-off-by: Angus Chen Reviewed-by: Jason Wang Reviewed-by: Michael S. Tsirkin Acked-by: Zhu Lingshan Message-Id: <20220923091013.191-1-angus.chen@jaguarmicro.com> Signed-off-by: Michael S. Tsirkin Signed-off-by: Sasha Levin

net: phy: Don't WARN for PHY_UP state in mdio_bus_phy_resume()

2022-10-05T08:39:43+00:00

[ Upstream commit ea64cdfad124922c931633e39287c5a31a9b14a1 ] Commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state") introduced a WARN() on resume from system sleep if a PHY is not in PHY_HALTED state. Commit 6dbe852c379f ("net: phy: Don't WARN for PHY_READY state in mdio_bus_phy_resume()") added an exemption for PHY_READY state from the WARN(). It turns out PHY_UP state needs to be exempted as well because the following may happen on suspend: mdio_bus_phy_suspend() phy_stop_machine() phydev->state = PHY_UP # if (phydev->state >= PHY_UP) Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state") Reported-by: Marek Szyprowski Tested-by: Marek Szyprowski Link: https://lore.kernel.org/netdev/2b1a1588-505e-dff3-301d-bfc1fb14d685@samsung.com/ Signed-off-by: Lukas Wunner Acked-by: Florian Fainelli Cc: Xiaolei Wang Link: https://lore.kernel.org/r/8128fdb51eeebc9efbf3776a4097363a1317aaf1.1663905575.git.lukas@wunner.de Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: stmmac: power up/down serdes in stmmac_open/release

2022-10-05T08:39:43+00:00

[ Upstream commit 49725ffc15fc4e9fae68c55b691fd25168cbe5c1 ] This commit fixes DMA engine reset timeout issue in suspend/resume with ADLink I-Pi SMARC Plus board which dmesg shows: ... [ 54.678271] PM: suspend exit [ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL) [ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0 ... [ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7 [ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma [ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed [ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed ... The issue is related with serdes which impacts clock. There is serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to commit b9663b7ca6ff78 ("net: stmmac: Enable SERDES power up/down sequence") for detial. When issue is reproduced, DMA engine clock is not ready because serdes is not powered up. To reproduce DMA engine reset timeout issue with hardware which has serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click "Power Off/Log Out" -> "Suspend" menu, it disables network interface, then goes to sleep mode. When it wakes up, it enables network interface again. Stmmac driver is called in this way: 1. stmmac_release: Stop network interface. In this function, it disables DMA engine and network interface; 2. stmmac_suspend: It is called in kernel suspend flow. But because network interface has been disabled(netif_running(ndev) is false), it does nothing and returns directly; 3. System goes into S3 or S0ix state. Some time later, system is waken up by keyboard or mouse; 4. stmmac_resume: It does nothing because network interface has been disabled; 5. stmmac_open: It is called to enable network interace again. DMA engine is initialized in this API, but serdes is not power on so there will be DMA engine reset timeout issue. Similarly, serdes powerdown should be added in stmmac_release. Network interface might be disabled by cmd "ifconfig eth0 down", DMA engine, phy and mac have been disabled in ndo_stop callback, serdes should be powered down as well. It doesn't make sense that serdes is on while other components have been turned off. If ethernet interface is in enabled state(netif_running(ndev) is true) before suspend/resume, the issue couldn't be reproduced because serdes could be powered up in stmmac_resume. Because serdes_powerup is added in stmmac_open, it doesn't need to be called in probe function. Fixes: b9663b7ca6ff78 ("net: stmmac: Enable SERDES power up/down sequence") Signed-off-by: Junxiao Chang Reviewed-by: Voon Weifeng Tested-by: Jimmy JS Chen Tested-by: Looi, Hong Aun Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

nvme: Fix IOC_PR_CLEAR and IOC_PR_RELEASE ioctls for nvme devices

2022-10-05T08:39:43+00:00

[ Upstream commit c292a337d0e45a292c301e3cd51c35aa0ae91e95 ] The IOC_PR_CLEAR and IOC_PR_RELEASE ioctls are non-functional on NVMe devices because the nvme_pr_clear() and nvme_pr_release() functions set the IEKEY field incorrectly. The IEKEY field should be set only when the key is zero (i.e, not specified). The current code does it backwards. Furthermore, the NVMe spec describes the persistent reservation "clear" function as an option on the reservation release command. The current implementation of nvme_pr_clear() erroneously uses the reservation register command. Fix these errors. Note that NVMe version 1.3 and later specify that setting the IEKEY field will return an error of Invalid Field in Command. The fix will set IEKEY when the key is zero, which is appropriate as these ioctls consider a zero key to be "unspecified", and the intention of the spec change is to require a valid key. Tested on a version 1.4 PCI NVMe device in an Azure VM. Fixes: 1673f1f08c88 ("nvme: move block_device_operations and ns/ctrl freeing to common code") Fixes: 1d277a637a71 ("NVMe: Add persistent reservation ops") Signed-off-by: Michael Kelley Signed-off-by: Christoph Hellwig Signed-off-by: Sasha Levin

net/mlxbf_gige: Fix an IS_ERR() vs NULL bug in mlxbf_gige_mdio_probe

2022-10-05T08:39:43+00:00

[ Upstream commit 4774db8dfc6a2e6649920ebb2fc8e2f062c2080d ] The devm_ioremap() function returns NULL on error, it doesn't return error pointers. Fixes: 3a1a274e933f ("mlxbf_gige: compute MDIO period based on i1clk") Signed-off-by: Peng Wu Link: https://lore.kernel.org/r/20220923023640.116057-1-wupeng58@huawei.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

cxgb4: fix missing unlock on ETHOFLD desc collect fail path

2022-10-05T08:39:43+00:00

[ Upstream commit c635ebe8d911a93bd849a9419b01a58783de76f1 ] The label passed to the QDESC_GET for the ETHOFLD TXQ, RXQ, and FLQ, is the 'out' one, which skips the 'out_unlock' label, and thus doesn't unlock the 'uld_mutex' before returning. Additionally, since commit 5148e5950c67 ("cxgb4: add EOTID tracking and software context dump"), the access to these ETHOFLD hardware queues should be protected by the 'mqprio_mutex' instead. Fixes: 2d0cb84dd973 ("cxgb4: add ETHOFLD hardware queue support") Fixes: 5148e5950c67 ("cxgb4: add EOTID tracking and software context dump") Signed-off-by: Rafael Mendonca Reviewed-by: Rahul Lakkireddy Link: https://lore.kernel.org/r/20220922175109.764898-1-rafaelmendsr@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

usbnet: Fix memory leak in usbnet_disconnect()

2022-10-05T08:39:42+00:00

[ Upstream commit a43206156263fbaf1f2b7f96257441f331e91bb7 ] Currently usbnet_disconnect() unanchors and frees all deferred URBs using usb_scuttle_anchored_urbs(), which does not free urb->context, causing a memory leak as reported by syzbot. Use a usb_get_from_anchor() while loop instead, similar to what we did in commit 19cfe912c37b ("Bluetooth: btusb: Fix memory leak in play_deferred"). Also free urb->sg. Reported-and-tested-by: syzbot+dcd3e13cf4472f2e0ba1@syzkaller.appspotmail.com Fixes: 69ee472f2706 ("usbnet & cdc-ether: Autosuspend for online devices") Fixes: 638c5115a794 ("USBNET: support DMA SG") Signed-off-by: Peilin Ye Link: https://lore.kernel.org/r/20220923042551.2745-1-yepeilin.cs@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin