kernel/linux.git/drivers, branch v3.0.77

Revert :can: sja1000: fix handling on dt properties on little endian systems"

2013-05-08T02:57:28+00:00

This reverts commit 55fe10a686c3a8bce7bddc149e4ebb12f5a18c25 which is commit 0443de5fbf224abf41f688d8487b0c307dc5a4b4 upstream. This causes a build breakage on 3.0, so we shouldn't apply it to that tree. Reported-by: Jiri Slaby Cc: Christoph Fritz Cc: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

mfd: adp5520: Restore mode bits on resume

2013-05-08T02:57:28+00:00

commit c6cc25fda58da8685ecef3f179adc7b99c8253b2 upstream. The adp5520 unfortunately also clears the BL_EN bit when the nSTNDBY bit is cleared. So we need to make sure to restore it during resume if it was set before suspend. Signed-off-by: Lars-Peter Clausen Acked-by: Michael Hennerich Signed-off-by: Samuel Ortiz Signed-off-by: Greg Kroah-Hartman

mmc: core: Fix bit width test failing on old eMMC cards

2013-05-08T02:57:27+00:00

commit 836dc2fe89c968c10cada87e0dfae6626f8f9da3 upstream. PARTITION_SUPPORT needs to be set before doing the compare on version number so the bit width test does not get invalid data. Before this patch, a Sandisk iNAND eMMC card would detect 1-bit width although the hardware supports 4-bit. Only affects old emmc devices - pre 4.4 devices. Reported-by: Elad Yi Signed-off-by: Philip Rakity Signed-off-by: Chris Ball Signed-off-by: Greg Kroah-Hartman

drivers/rtc/rtc-cmos.c: don't disable hpet emulation on suspend

2013-05-08T02:57:26+00:00

commit e005715efaf674660ae59af83b13822567e3a758 upstream. There's a bug where rtc alarms are ignored after the rtc cmos suspends but before the system finishes suspend. Since hpet emulation is disabled and it still handles the interrupts, a wake event is never registered which is done from the rtc layer. This patch reverts commit d1b2efa83fbf ("rtc: disable hpet emulation on suspend") which disabled hpet emulation. To fix the problem mentioned in that commit, hpet_rtc_timer_init() is called directly on resume. Signed-off-by: Derek Basehore Cc: Maxim Levitsky Cc: "H. Peter Anvin" Cc: Thomas Gleixner Cc: Ingo Molnar Cc: "Rafael J. Wysocki" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

PCI / ACPI: Don't query OSC support with all possible controls

2013-05-08T02:57:24+00:00

commit 545d6e189a41c94c11f55045a771118eccc9d9eb upstream. Found problem on system that firmware that could handle pci aer. Firmware get error reporting after pci injecting error, before os boots. But after os boots, firmware can not get report anymore, even pci=noaer is passed. Root cause: BIOS _OSC has problem with query bit checking. It turns out that BIOS vendor is copying example code from ACPI Spec. In ACPI Spec 5.0, page 290: If (Not(And(CDW1,1))) // Query flag clear? { // Disable GPEs for features granted native control. If (And(CTRL,0x01)) // Hot plug control granted? { Store(0,HPCE) // clear the hot plug SCI enable bit Store(1,HPCS) // clear the hot plug SCI status bit } ... } When Query flag is set, And(CDW1,1) will be 1, Not(1) will return 0xfffffffe. So it will get into code path that should be for control set only. BIOS acpi code should be changed to "If (LEqual(And(CDW1,1), 0)))" Current kernel code is using _OSC query to notify firmware about support from OS and then use _OSC to set control bits. During query support, current code is using all possible controls. So will execute code that should be only for control set stage. That will have problem when pci=noaer or aer firmware_first is used. As firmware have that control set for os aer already in query support stage, but later will not os aer handling. We should avoid passing all possible controls, just use osc_control_set instead. That should workaround BIOS bugs with affected systems on the field as more bios vendors are copying sample code from ACPI spec. Signed-off-by: Yinghai Lu Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

i2c: xiic: must always write 16-bit words to TX_FIFO

2013-05-08T02:57:24+00:00

commit c39e8e4354ce4daf23336de5daa28a3b01f00aa6 upstream. The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be written, while the upper two bits are flags to indicate stop/start. The driver apparently attempted to optimize write access, by only writing a byte in those cases where the stop/start bits are zero. However, we have seen cases where the lower byte is duplicated onto the upper byte by the hardware, which causes inadvertent stop/starts. This patch changes the write access to the transmit FIFO to always be 16 bits wide. Signed off by: Steven A. Falco Signed-off-by: Wolfram Sang Signed-off-by: Greg Kroah-Hartman

fbcon: when font is freed, clear also vc_font.data

2013-05-08T02:57:23+00:00

commit e6637d5427d2af9f3f33b95447bfc5347e5ccd85 upstream. commit ae1287865f5361fa138d4d3b1b6277908b54eac9 Author: Dave Airlie Date: Thu Jan 24 16:12:41 2013 +1000 fbcon: don't lose the console font across generic->chip driver switch uses a pointer in vc->vc_font.data to load font into the new driver. However if the font is actually freed, we need to clear the data so that we don't reload font from dangling pointer. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=892340 Signed-off-by: Mika Kuoppala Signed-off-by: Dave Airlie Signed-off-by: Greg Kroah-Hartman

tty: fix up atime/mtime mess, take three

2013-05-08T02:57:22+00:00

commit b0b885657b6c8ef63a46bc9299b2a7715d19acde upstream. We first tried to avoid updating atime/mtime entirely (commit b0de59b5733d: "TTY: do not update atime/mtime on read/write"), and then limited it to only update it occasionally (commit 37b7f3c76595: "TTY: fix atime/mtime regression"), but it turns out that this was both insufficient and overkill. It was insufficient because we let people attach to the shared ptmx node to see activity without even reading atime/mtime, and it was overkill because the "only once a minute" means that you can't really tell an idle person from an active one with 'w'. So this tries to fix the problem properly. It marks the shared ptmx node as un-notifiable, and it lowers the "only once a minute" to a few seconds instead - still long enough that you can't time individual keystrokes, but short enough that you can tell whether somebody is active or not. Reported-by: Simon Kirby Acked-by: Jiri Slaby Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

serial_core.c: add put_device() after device_find_child()

2013-05-08T02:57:22+00:00

commit 5a65dcc04cda41f4122aacc37a5a348454645399 upstream. The serial core uses device_find_child() but does not drop the reference to the retrieved child after using it. This patch add the missing put_device(). What I have done to test this issue. I used a machine with an AMBA PL011 serial driver. I tested the patch on next-20120408 because the last branch [next-20120415] does not boot on this board. For test purpose, I added some pr_info() messages to print the refcount after device_find_child() (lines: 1937,2009), and after put_device() (lines: 1947, 2021). Boot the machine *without* put_device(). Then: echo reboot > /sys/power/disk echo disk > /sys/power/state [ 87.058575] uart_suspend_port:1937 refcount 4 [ 87.058582] uart_suspend_port:1947 refcount 4 [ 87.098083] uart_resume_port:2009refcount 5 [ 87.098088] uart_resume_port:2021 refcount 5 echo disk > /sys/power/state [ 103.055574] uart_suspend_port:1937 refcount 6 [ 103.055580] uart_suspend_port:1947 refcount 6 [ 103.095322] uart_resume_port:2009 refcount 7 [ 103.095327] uart_resume_port:2021 refcount 7 echo disk > /sys/power/state [ 252.459580] uart_suspend_port:1937 refcount 8 [ 252.459586] uart_suspend_port:1947 refcount 8 [ 252.499611] uart_resume_port:2009 refcount 9 [ 252.499616] uart_resume_port:2021 refcount 9 The refcount continuously increased. Boot the machine *with* this patch. Then: echo reboot > /sys/power/disk echo disk > /sys/power/state [ 159.333559] uart_suspend_port:1937 refcount 4 [ 159.333566] uart_suspend_port:1947 refcount 3 [ 159.372751] uart_resume_port:2009 refcount 4 [ 159.372755] uart_resume_port:2021 refcount 3 echo disk > /sys/power/state [ 185.713614] uart_suspend_port:1937 refcount 4 [ 185.713621] uart_suspend_port:1947 refcount 3 [ 185.752935] uart_resume_port:2009 refcount 4 [ 185.752940] uart_resume_port:2021 refcount 3 echo disk > /sys/power/state [ 207.458584] uart_suspend_port:1937 refcount 4 [ 207.458591] uart_suspend_port:1947 refcount 3 [ 207.498598] uart_resume_port:2009 refcount 4 [ 207.498605] uart_resume_port:2021 refcount 3 The refcount correctly handled. Signed-off-by: Federico Vaga Signed-off-by: Greg Kroah-Hartman

s390/memory hotplug: prevent offline of active memory increments

2013-05-08T02:57:22+00:00

commit 94c163663fc1dcfc067a5fb3cc1446b9469975ce upstream. In case a machine supports memory hotplug all active memory increments present at IPL time have been initialized with a "usecount" of 1. This is wrong if the memory increment size is larger than the memory section size of the memory hotplug code. If that is the case the usecount must be initialized with the number of memory sections that fit into one memory increment. Otherwise it is possible to put a memory increment into standby state even if there are still active sections. Afterwards addressing exceptions might happen which cause the kernel to panic. However even worse, if a memory increment was put into standby state and afterwards into active state again, it's contents would have been zeroed, leading to memory corruption. This was only an issue for machines that support standby memory and have at least 256GB memory. This is broken since commit fdb1bb15 "[S390] sclp/memory hotplug: fix initial usecount of increments". Signed-off-by: Heiko Carstens Reviewed-by: Gerald Schaefer Signed-off-by: Martin Schwidefsky Signed-off-by: Greg Kroah-Hartman