kernel/linux.git/drivers/usb/typec, branch v6.1.176

usb: typec: tcpm: reset internal port states on soft reset AMS

2026-06-19T11:37:31+00:00

commit 2909f0d4994fb4306bf116df5ccee797791fce2c upstream. Reset internal port states (such as vdm_sm_running and explicit_contract) on soft reset AMS as the port needs to negotiate a new contract. The consequence of leaving the states in as-is cond are as follows: * port is in SRC power role and an explicit contract is negotiated with the port partner (in sink role) * port partner sends a Soft Reset AMS while VDM State Machine is running * port accepts the Soft Reset request and the port advertises src caps * port partner sends a Request message but since the explicit_contract and vdm_sm_running are true from previous negotiation, the port ends up sending Soft Reset instead of Accept msg. Stub Log: [ 203.653942] AMS DISCOVER_IDENTITY start [ 203.653947] PD TX, header: 0x176f [ 203.655901] PD TX complete, status: 0 [ 203.657470] PD RX, header: 0x124f [1] [ 203.657477] Rx VDM cmd 0xff008081 type 2 cmd 1 len 1 [ 203.657482] AMS DISCOVER_IDENTITY finished [ 203.657484] cc:=4 [ 204.155698] PD RX, header: 0x144f [1] [ 204.155718] Rx VDM cmd 0xeeee8001 type 0 cmd 1 len 1 [ 204.155741] PD TX, header: 0x196f [ 204.157622] PD TX complete, status: 0 [ 204.160060] PD RX, header: 0x4d [1] [ 204.160066] state change SRC_READY -> SOFT_RESET [rev2 SOFT_RESET_AMS] [ 204.160076] PD TX, header: 0x163 [ 204.162486] PD TX complete, status: 0 [ 204.162832] AMS SOFT_RESET_AMS finished [ 204.162840] cc:=4 [ 204.162891] AMS POWER_NEGOTIATION start [ 204.162896] state change SOFT_RESET -> AMS_START [rev2 POWER_NEGOTIATION] [ 204.162908] state change AMS_START -> SRC_SEND_CAPABILITIES [rev2 POWER_NEGOTIATION] [ 204.162913] PD TX, header: 0x1361 [ 204.165529] PD TX complete, status: 0 [ 204.165571] pending state change SRC_SEND_CAPABILITIES -> SRC_SEND_CAPABILITIES_TIMEOUT @ 60 ms [rev2 POWER_NEGOTIATION] [ 204.166996] PD RX, header: 0x1242 [1] [ 204.167009] state change SRC_SEND_CAPABILITIES -> SRC_SOFT_RESET_WAIT_SNK_TX [rev2 POWER_NEGOTIATION] [ 204.167019] AMS POWER_NEGOTIATION finished [ 204.167020] cc:=4 [ 204.167083] AMS SOFT_RESET_AMS start [ 204.167086] state change SRC_SOFT_RESET_WAIT_SNK_TX -> SOFT_RESET_SEND [rev2 SOFT_RESET_AMS] [ 204.167092] PD TX, header: 0x16d [ 204.168824] PD TX complete, status: 0 [ 204.168854] pending state change SOFT_RESET_SEND -> HARD_RESET_SEND @ 60 ms [rev2 SOFT_RESET_AMS] [ 204.171876] PD RX, header: 0x43 [1] [ 204.171879] AMS SOFT_RESET_AMS finished This causes COMMON.PROC.PD.11.2 check failure for TEST.PD.VDM.SRC.2_Rev2Src test on the PD compliance tester. Signed-off-by: Amit Sunil Dhamne Fixes: 8d3a0578ad1a ("usb: typec: tcpm: Respond Wait if VDM state machine is running") Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: stable Reviewed-by: Badhri Jagan Sridharan Acked-by: Heikki Krogerus Link: https://patch.msgid.link/20260414-fix-soft-reset-v1-1-01d7cb9764e2@google.com Signed-off-by: Amit Sunil Dhamne Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: Don't update power_supply on power role change if not connected

2026-06-19T11:37:29+00:00

[ Upstream commit d98d413ca65d0790a8f3695d0a5845538958ab84 ] We only need to update the power_supply on power role change if the port is connected, because otherwise the online status should be the same for both cases. Cc: stable Fixes: 7616f006db07 ("usb: typec: ucsi: Update power_supply on power role change") Signed-off-by: Myrrh Periwinkle Reported-and-tested-by: Sergey Senozhatsky Link: https://patch.msgid.link/20260519-ucsi-fix-2-v1-2-6f1239535187@qtmlabs.xyz Signed-off-by: Greg Kroah-Hartman [ changed `UCSI_CONSTAT(con, CONNECTED)` accessor macro to `con->status.flags & UCSI_CONSTAT_CONNECTED` ] Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: Check if power role change actually happened before handling

2026-06-19T11:37:29+00:00

[ Upstream commit b80e7d34c7ea6a564525119d6138fbb577a23dba ] The CrOS EC may send a connector status change event with the power direction changed flag set even if the power direction hasn't actually changed after initiating a SET_PDR command internally [1]. In practice this happens on every system suspend due to other changes performed by the EC [2][3][4], causing suspend to fail. Fix this by checking if the power role change actually happened before handling it. [1]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=1689;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794 [2]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=3923;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794 [3]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=5094;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794 [4]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=2229;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794 Cc: stable Fixes: 7616f006db07 ("usb: typec: ucsi: Update power_supply on power role change") Signed-off-by: Myrrh Periwinkle Reported-and-tested-by: Sergey Senozhatsky Reviewed-by: Heikki Krogerus Link: https://patch.msgid.link/20260519-ucsi-fix-2-v1-1-6f1239535187@qtmlabs.xyz Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: validate connector number in ucsi_connector_change()

2026-06-19T11:36:59+00:00

commit 288a81a8507052bcfbf884d39a463c44c42c5fd9 upstream. The connector number in a UCSI CCI notification is a 7-bit field supplied by the PPM. ucsi_connector_change() uses it to index the ucsi->connector[] array without checking it against the number of connectors the PPM reported at init time, so a buggy or malicious PPM (EC firmware, or an I2C-attached UCSI controller on the ccg / stm32g0 / glink transports) can drive schedule_work() on memory past the end of the array. Reject connector numbers that are zero or exceed cap.num_connectors before dereferencing the array. Assisted-by: gkh_clanker_t1000 Cc: Heikki Krogerus Cc: Benson Leung Cc: Jameson Thies Cc: Nathan Rebello Cc: Johan Hovold Cc: Pooja Katiyar Cc: Hsin-Te Yuan Cc: Abel Vesa Cc: stable Reviewed-by: Abel Vesa Reviewed-by: Heikki Krogerus Reviewed-by: Benson Leung Link: https://patch.msgid.link/2026051351-truck-steadfast-df48@gregkh Signed-off-by: Greg Kroah-Hartman

usb: typec: wcove: don't write past struct pd_message in wcove_read_rx_buffer()

2026-06-19T11:36:59+00:00

commit 4af7ad0e6d7aa4403dbb1dac7b9659b0421efcaa upstream. wcove_read_rx_buffer() copies the PD RX FIFO into the caller's struct pd_message with for (i = 0; i < USBC_RXINFO_RXBYTES(info); i++) regmap_read(wcove->regmap, USBC_RX_DATA + i, msg + i); which has two problems: USBC_RXINFO_RXBYTES() is a 5-bit field (max 31) while struct pd_message is 30 bytes (__le16 header + __le32 payload[PD_MAX_PAYLOAD], packed). The byte count latched in RXINFO is the number of bytes the port partner put on the wire, so a malicious partner that transmits a 31-byte frame can drive the loop one byte past the destination if the WCOVE BMC receiver does not enforce the PD object-count limit in hardware. The existing FIXME flagged this as unverified. Independently, regmap_read() takes an unsigned int * and stores a full unsigned int at the destination. Passing the byte pointer msg + i means each iteration writes four bytes; the high three are zero (val_bits is 8) and are normally overwritten by the next iteration, but the final iteration's high bytes are not. With RXBYTES == 30 the i == 29 iteration already writes three zero bytes past msg, which sits on the IRQ thread's stack in wcove_typec_irq(). Clamp the loop to sizeof(struct pd_message) and read each register into a local before storing only its low byte, so the copy can never exceed the destination regardless of what RXINFO reports. Assisted-by: gkh_clanker_t1000 Cc: stable Reviewed-by: Heikki Krogerus Link: https://patch.msgid.link/2026051347-clustered-deflected-9543@gregkh Signed-off-by: Greg Kroah-Hartman

usb: typec: altmodes/displayport: validate count before reading Status Update VDO

2026-06-19T11:36:59+00:00

commit 8a18f896e667df491331371b55d4ad644dc51d60 upstream. A broken/malicious device can send the incorrect count for a status update VDO, which will cause the kernel to read uninitialized stack data and send it off elsewhere. Fix this up by correctly verifying the count for the update object. Assisted-by: gkh_clanker_t1000 Cc: stable Reviewed-by: Heikki Krogerus Link: https://patch.msgid.link/2026051350-reacquire-sculpture-4244@gregkh Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: displayport: NAK DP_CMD_CONFIGURE without a payload VDO

2026-06-19T11:36:59+00:00

commit 167dd8d12226587ee554f520aed0256b7769cd5d upstream. ucsi_displayport_vdm() handles a DP_CMD_CONFIGURE by copying the first payload VDO from data[], but unlike the equivalent handler in altmodes/displayport.c it does not check that count covers a VDO beyond the header. A header-only Configure VDM (count == 1) would read one u32 past the caller's array. In the normal UCSI path the caller controls count, so this is hardening for non-standard delivery paths. NAK and bail when no configuration VDO is present, matching the generic DP altmode driver's existing guard. Assisted-by: gkh_clanker_t1000 Cc: Pooja Katiyar Cc: Johan Hovold Cc: stable Reviewed-by: Heikki Krogerus Link: https://patch.msgid.link/2026051351-vividly-flattered-eb3d@gregkh Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: ccg: reject firmware images without a ':' record header

2026-06-19T11:36:58+00:00

commit d7486952bf74e546ee3748fb14b2d07881fa6273 upstream. do_flash() locates the first .cyacd record with p = strnchr(fw->data, fw->size, ':'); while (p < eof) { s = strnchr(p + 1, eof - p - 1, ':'); ... } If the firmware image contains no ':' byte, strnchr() returns NULL. NULL compares less than the valid kernel pointer eof, so the loop body runs and strnchr() is called with p + 1 == (void *)1 and a length of roughly (unsigned long)eof, causing a wonderful crash. The not_signed_fw fallthrough earlier in do_flash() and the chip-state branches in ccg_fw_update_needed() allow an unsigned blob to reach this loop, so a root user who can place a crafted file under /lib/firmware and write the do_flash sysfs attribute can trigger the oops. Bail out with -EINVAL when the initial strnchr() returns NULL. Assisted-by: gkh_clanker_t1000 Cc: stable Cc: Heikki Krogerus Reviewed-by: Heikki Krogerus Signed-off-by: Greg Kroah-Hartman Link: https://patch.msgid.link/2026051405-posture-shrill-7884@gregkh Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: psy: Fix voltage and current max for non-Fixed PDOs

2026-03-04T12:20:33+00:00

[ Upstream commit 6811e0a08bdce6b2767414caf17fda24c2e4e032 ] ucsi_psy_get_voltage_max and ucsi_psy_get_current_max are calculated using whichever pdo is in the last position of the src_pdos array, presuming it to be a fixed pdo, so the pdo_fixed_voltage or pdo_max_current helpers are used on that last pdo. However, non-Fixed PDOs such as Battery PDOs, Augmented PDOs (used for AVS and for PPS) may exist, and are always at the end of the array if they do. In the event one of these more advanced chargers are attached the helpers for fixed return mangled values. Here's an example case of a Google Pixel Flex Dual Port 67W USB-C Fast Charger with PPS support: POWER_SUPPLY_NAME=ucsi-source-psy-cros_ec_ucsi.4.auto2 POWER_SUPPLY_TYPE=USB POWER_SUPPLY_CHARGE_TYPE=Standard POWER_SUPPLY_USB_TYPE=C [PD] PD_PPS PD_DRP POWER_SUPPLY_ONLINE=1 POWER_SUPPLY_VOLTAGE_MIN=5000000 POWER_SUPPLY_VOLTAGE_MAX=13400000 POWER_SUPPLY_VOLTAGE_NOW=20000000 POWER_SUPPLY_CURRENT_MAX=5790000 POWER_SUPPLY_CURRENT_NOW=3250000 Voltage Max is reading as 13.4V, but that's an incorrect decode of the PPS APDO in the last position. Same goes for CURRENT_MAX. 5.79A is incorrect. Instead, enumerate through the src_pdos and filter just for Fixed PDOs for now, and find the one with the highest voltage and current respectively. After, from the same charger: POWER_SUPPLY_NAME=ucsi-source-psy-cros_ec_ucsi.4.auto2 POWER_SUPPLY_TYPE=USB POWER_SUPPLY_CHARGE_TYPE=Standard POWER_SUPPLY_USB_TYPE=C [PD] PD_PPS PD_DRP POWER_SUPPLY_ONLINE=1 POWER_SUPPLY_VOLTAGE_MIN=5000000 POWER_SUPPLY_VOLTAGE_MAX=20000000 POWER_SUPPLY_VOLTAGE_NOW=20000000 POWER_SUPPLY_CURRENT_MAX=4000000 POWER_SUPPLY_CURRENT_NOW=3250000 Signed-off-by: Benson Leung Reviewed-by: Heikki Krogerus Link: https://patch.msgid.link/20251208174918.289394-3-bleung@chromium.org Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: typec: ucsi: Handle incorrect num_connectors capability

2026-01-11T14:18:49+00:00

[ Upstream commit 30cd2cb1abf4c4acdb1ddb468c946f68939819fb ] The UCSI spec states that the num_connectors field is 7 bits, and the 8th bit is reserved and should be set to zero. Some buggy FW has been known to set this bit, and it can lead to a system not booting. Flag that the FW is not behaving correctly, and auto-fix the value so that the system boots correctly. Found on Lenovo P1 G8 during Linux enablement program. The FW will be fixed, but seemed worth addressing in case it hit platforms that aren't officially Linux supported. Signed-off-by: Mark Pearson Reviewed-by: Heikki Krogerus Link: https://lore.kernel.org/r/20250821185319.2585023-1-mpearson-lenovo@squebb.ca Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin