kernel/linux.git/drivers/usb/serial, branch v5.2.16

USB: serial: option: Add Motorola modem UARTs

2019-08-25T14:10:35+00:00

commit 6caf0be40a707689e8ff8824fdb96ef77685b1ba upstream. On Motorola Mapphone devices such as Droid 4 there are five USB ports that do not use the same layout as Gobi 1K/2K/etc devices listed in qcserial.c. So we should use qcaux.c or option.c as noted by Dan Williams . As the Motorola USB serial ports have an interrupt endpoint as shown with lsusb -v, we should use option.c instead of qcaux.c as pointed out by Johan Hovold . The ff/ff/ff interfaces seem to always be UARTs on Motorola devices. For the other interfaces, class 0x0a (CDC Data) should not in general be added as they are typically part of a multi-interface function as noted earlier by Bjørn Mork . However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a class is only used for flashing the modem firmware, and there are no other interfaces. So I've added that too with more details below as it works just fine. The ttyUSB ports on Droid 4 are: ttyUSB0 DIAG, CQDM-capable ttyUSB1 MUX or NMEA, no response ttyUSB2 MUX or NMEA, no response ttyUSB3 TCMD ttyUSB4 AT-capable The ttyUSB0 is detected as QCDM capable by ModemManager. I think it's only used for debugging with ModemManager --debug for sending custom AT commands though. ModemManager already can manage data connection using the USB QMI ports that are already handled by the qmi_wwan.c driver. To enable the MUX or NMEA ports, it seems that something needs to be done additionally to enable them, maybe via the DIAG or TCMD port. It might be just a NVRAM setting somewhere, but I have no idea what NVRAM settings may need changing for that. The TCMD port seems to be a Motorola custom protocol for testing the modem and to configure it's NVRAM and seems to work just fine based on a quick test with a minimal tcmdrw tool I wrote. The voice modem AT-capable port seems to provide only partial support, and no PM support compared to the TS 27.010 based UART wired directly to the modem. The UARTs added with this change are the same product IDs as the Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't have any mdm9600 based devices, so I have only tested these on mdm6600 based droid 4. Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android Linux kernel driver moto_flashqsc.c just seems to change the port->bulk_out_size to 8K from the default. And is only used for flashing the modem firmware it seems. I've verified that flashing the modem with signed firmware works just fine with the option driver after manually toggling the GPIO pins, so I've added droid 4 modem flashing mode to the option driver. I've not added the other devices listed in moto_flashqsc.c in case they really need different port->bulk_out_size. Those can be added as they get tested to work for flashing the modem. After this patch the output of /sys/kernel/debug/usb/devices has the following for normal 22b8:2a70 mode including the related qmi_wwan interfaces: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=2a70 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms In 22b8:900e "qc_dload" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=900e Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms And in 22b8:4281 "ram_downloader" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=4281 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Cc: Bjørn Mork Cc: Dan Williams Cc: Lars Melin Cc: Marcel Partap Cc: Merlijn Wajer Cc: Michael Scott Cc: NeKit Cc: Pavel Machek Cc: Sebastian Reichel Tested-by: Pavel Machek Signed-off-by: Tony Lindgren Cc: stable Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add the BroadMobi BM818 card

2019-08-25T14:10:35+00:00

commit e5d8badf37e6b547842f2fcde10361b29e08bd36 upstream. Add a VID:PID for the BroadMobi BM818 M.2 card T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2060 Rev=00.00 S: Manufacturer=Qualcomm, Incorporated S: Product=Qualcomm CDMA Technologies MSM C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none) I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) Signed-off-by: Bob Ham Signed-off-by: Angus Ainslie (Purism) Cc: stable [ johan: use USB_DEVICE_INTERFACE_CLASS() ] Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: serial: option: Add support for ZTE MF871A

2019-08-25T14:10:35+00:00

commit 7e7ae38bf928c5cfa6dd6e9a2cf8b42c84a27c92 upstream. This patch adds support for MF871A USB modem (aka Speed USB STICK U03) to option driver. This modem is manufactured by ZTE corporation, and sold by KDDI. Interface layout: 0: AT 1: MODEM usb-devices output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1481 Rev=52.87 S: Manufacturer=ZTE,Incorporated S: Product=ZTE Technologies MSM S: SerialNumber=1234567890ABCDEF C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Co-developed-by: Hiroyuki Yamamoto Signed-off-by: Hiroyuki Yamamoto Signed-off-by: Yoshiaki Okamoto Cc: stable Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add D-Link DWM-222 device ID

2019-08-25T14:10:35+00:00

commit 552573e42aab5f75aff9bab855a9677979d9a7d5 upstream. Add device id for D-Link DWM-222 A2. MI_00 D-Link HS-USB Diagnostics MI_01 D-Link HS-USB Modem MI_02 D-Link HS-USB AT Port MI_03 D-Link HS-USB NMEA MI_04 D-Link HS-USB WWAN Adapter (qmi_wwan) MI_05 USB Mass Storage Device Cc: stable@vger.kernel.org Signed-off-by: Rogan Dawes Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add support for GosunCn ME3630 RNDIS mode

2019-07-14T06:01:10+00:00

commit aed2a26283528fb69c38e414f649411aa48fb391 upstream. Added USB IDs for GosunCn ME3630 cellular module in RNDIS mode. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=03 Dev#= 18 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0601 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber=b950269c C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: serial: ftdi_sio: add ID for isodebug v1

2019-07-14T06:01:10+00:00

commit f8377eff548170e8ea8022c067a1fbdf9e1c46a8 upstream. This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the second channel is available for use as a serial port. Signed-off-by: Andreas Fritiofson Cc: stable Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Telit 0x1260 and 0x1261 compositions

2019-05-21T09:27:24+00:00

Added support for Telit LE910Cx 0x1260 and 0x1261 compositions. Signed-off-by: Daniele Palmas Cc: stable Signed-off-by: Johan Hovold

USB: serial: pl2303: add Allied Telesis VT-Kit3

2019-05-21T09:26:14+00:00

This is adds the vendor and device id for the AT-VT-Kit3 which is a pl2303-based device. Signed-off-by: Chris Packham Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode

2019-05-21T09:19:02+00:00

Added IDs for Simcom SIM7500/SIM7600 series cellular module in RNDIS mode. Reserved the interface for ADB. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9011 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: f81232: implement break control

2019-05-03T07:19:55+00:00

Implement Fintek F81232 break on/off with LCR register. It's the same with 16550A LCR register layout. Signed-off-by: Ji-Ze Hong (Peter Hong) [ johan: fix corrupt line settings on break due to missing shadow_lcr update in set_termios() ] Signed-off-by: Johan Hovold