kernel/linux.git/drivers/usb/serial, branch v2.6.28

USB: pl2303: add id for Hewlett-Packard LD220-HP POS pole display

2008-12-17T18:49:15+00:00

Add id for the Hewlett-Packard LD220-HP POS pole display. Bus 002 Device 002: ID 03f0:3524 Hewlett-Packard Signed-off-by: Mike Provencher Signed-off-by: Greg Kroah-Hartman

USB: set correct configuration in probe of ti_usb_3410_5052

2008-12-17T18:49:15+00:00

This driver transfers firmware. It may just as well set the correct configuration. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman

USB: add 5372:2303 to pl2303

2008-12-17T18:49:15+00:00

This patch adds the "Superial" USB-Serial converter to pl2303 so that it is detected, by the correct driver. Adds the relevant vendor:product (5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has been tested against 2.6.24-22-generic. Signed-off-by: Matthew D Arnold Signed-off-by: Greg Kroah-Hartman

USB: ftdi_sio: Adding Ewert Energy System's CANdapter PID

2008-12-17T18:49:11+00:00

The following patch adds in the USB PID for Ewert Energy System's CANdapter device (CANBUS to USB-Serial which uses the FTDI 245R chipset) to the ftdi_sio device driver. The patch was tested successfully on Linux kernel 2.6.27 under Ubuntu. Relevant output from /proc/bus/usb/devices (With patch installed): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0403 ProdID=9f80 Rev= 6.00 S: Manufacturer=Ewert Energy Systems S: Product=CANdapter S: SerialNumber=A6RGB3Z3 C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 90mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ftdi_sio E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Signed-off-by: Andrew Ewert Signed-off-by: Greg Kroah-Hartman

USB: tty: SprogII DCC controller identifiers

2008-12-17T18:49:11+00:00

Someone on rmweb reminded me this had been overlooked from ages ago.. Add the identifiers for the Sprog II USB. This is a DCC control interface using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been using it with insmod options for ages, this just puts it into the driver data. Signed-off-by: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman

Fix incorrect use of loose in tty/serial drivers

2008-12-05T21:40:52+00:00

[Folded together as one diff from 3] It should be 'lose', not 'loose'. Signed-off-by: Nick Andrew Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds

Add kref to fake tty used by USB console

2008-12-01T16:19:10+00:00

We alloc a fake tty in usb serial console setup function. we should init the tty's kref otherwise we will face WARN_ON after following invoke of tty_port_tty_set --> tty_kref_get. Signed-off-by: Kevin Hao Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds

USB: serial: add more Onda device ids to option driver

2008-12-01T06:24:03+00:00

Thanks to Domenico Riccio for pointing these out. Cc: Domenico Riccio Signed-off-by: Greg Kroah-Hartman

USB: ACE1001 patch for cp2101.c

2008-11-20T06:01:35+00:00

The patch which adds IDs for AKTAKOM USB->RS232 cable (http://www.aktakom.ru/product/kio/ace-1001.htm) is attached. From: M Kondrin Signed-off-by: Greg Kroah-Hartman

+ usb-serial-cp2101-add-enfora-gsm2228.patch added to -mm tree

2008-11-13T22:45:03+00:00

Enfora GSM2228 based on Cygnal Integrated Products chip uses the same cp2101 driver. Signed-off-by: Damir N Abdullin Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman